How often do you change the oil in a 2002 Ford Ranger?

The 2002 Ford Ranger requires a transmission fluid change every two years or 30,000 miles. Changing the oil involves emptying the old fluid, changing the filter and putting in new fluid.

How many liters does a Ford Ranger have?

Ford Ranger engine oil capacity Engine Capacity/Filter capacity litres (liters) Oil Change Intervals Ranger 2.3 (1993 – 1997) 4.7 8 000 km/ 6 months Ranger 2.3 16V (2001 – 2011) 3.8 6 months/ 5 000 miles Ranger 3.0 V6 (1993 – 1997) 4.25 8 000 km/ 6 months

What kind of oil does a Ranger take?

Changing the oil involves emptying the old fluid, changing the filter and putting in new fluid. The Ranger takes type H transmission fluid; you can substitute Mercon or Mercon V. Completing regular maintenance keeps the engine lubricated and running smoothly. Neglecting this job can result in costly damage.

When did the Ford Ranger get a Vulcan engine?

In 1991 it became available in the Ford Ranger where it replaced the Cologne 2.9 engine (which it is not related to) as the base V6 in the Ranger The Vulcan was a clean-sheet design using the metric system.

What kind of oil does a Ford Ranger use?

The engine oil is what lubricates the engine components to ensure successful operation, so performing a regular engine oil flush for Ford Ranger is critical to keep your truck at the top of its game.

What kind of engine does a Ford Ranger have?

Ford Ranger 3.0L V-6 Engine Displacement (Cubic Inches) 183 CID Block Cast Iron 60º V-6 Type Over-head Valve Engine Bore x Stroke 3.50 x 3.14

What are the dimensions of a 2002 Ford Ranger?

Independent unequal length control arms, coil springs, shock absorbers and stabilizer bar Independent unequal length control arms, torsion bars, shock absorbers and stabilizer bar Total Swept Area (sq. in). Total Swept Area (sq. in). 4×2 Regular Cab With Payload Pkg.#2 Dimensions and Capacities (1) Fuel Capacity (gal.)

What kind of valve does a Ford Ranger have?

The E6AE-AC/HC and F6DE-GA were built with 8.0mm valves through 7/26/99. These castings both had a 49cc, oval chamber. The F6DE-GC casting came with 7.0mm valves, conical springs and smaller retainers beginning in 7/27/99 and it has continued in that configuration up through ’03.

How do you reset the oil light on a Ford Ranger?

Ford Ranger Oil Light Reset without Driver Information Button. Make sure the Engine and Ignition is OFF. Press Both The Brake And Accelerator Pedals At The Same Time Turn the IGNITION ON. Continue Press the Brake and Accelerator Pedal for 20 Seconds until the OIL LIGHT Flashing and the Oil Lamp Will Illuminate.

How much fluid does a Ford Ranger need?

Need to know what type of fluid your Ford Ranger needs? 3.0 quarts (drain and refill) / 6.0 quarts with torque converter drain. Add more fluid as needed, 1/2 pint at a time. 3.0 quarts (drain and refill) / 6.0 quarts with torque converterdrain. Add more fluid as needed, 1/2 pint at a time.

How do you change the oil in a Ford Ranger?

For most Fords, you can wrap an old belt around the oil filter and unscrew it by hand. If you can’t do this, see our parts page to find a Ford Ranger oil filter wrench. If your Ranger is too low to the ground to access your drain plug and oil filter, be sure to use jack stands and safe jacking procedures before getting under your Ranger.

How to change the oil in a Dodge Ram?

Replace Cap – Put the oil fill cap back on the engine 11. Leak Inspection – Start vehicle and visually inspect for leaks 12. Remove Dipstick – Locate, remove and wipe oil dipstick 13. Read Oil Level – Reinsert dipstick, remove and then read oil level 14.

When did the Ford Ranger get its name?

Ford Ranger is a nameplate that has been used on three distinct model lines of vehicles sold by Ford. The name originated in 1958 when the Edsel Ranger was introduced as the base trim level of the Edsel model range. From 1965 to 1981, Ranger denoted various trim packages of the Ford F-Series (and Ford Bronco), serving as a mid- to top-level trim.

What kind of oil do you put in a Ford Ranger?

Pour the oil into the fill hole on top of the engine. Screw the cap back on. Idle the engine until the oil-temperature gauge begins registering. Check any leaks around the drain bolt or the filter. Ford recommends SAE 5W-20 for its 2.3-liter and 3.0-liter Ranger engines. For the 4.0-liter engine, use SAE 5W-30.

Where is the oil pump on a Ford Ranger?

Place an oil catchment bucket below the engine. After 24 hours connect a portable compressor to the breather pipe situated on top of the engine. Seal the air hose to the breather pipe securely. You can seal the oil dipstick if you wish, but not 100% necessary.

Is there a recall on Ford Ranger 3.2?

Ford ranger 3.2 oil pump recall If your Ford or Mazda 3.2 diesel engine oil and filter are changed in service and the oil is left to drain for longer than 10 minutes, the oil pump may fail to prime and leave the engine in a critical no lubrication situation.

The 2002 Ford Ranger requires a transmission fluid change every two years or 30,000 miles. Changing the oil involves emptying the old fluid, changing the filter and putting in new fluid.

Where is the oil cooler on a Ford Ranger?

The Ranger’s larger oil cooler means that there isn’t enough room for the oil filter to live down by the oil pan (which would be really convenient), and instead, it has been relocated to the side of the engine block, protruding at a right angle. This makes for a bit of patience and dexterity when it comes to routine maintenance.

The 2.3-liter EcoBoost engine found in the Ranger is slightly different from the one found in other FoMoCo applications, like the Ecoboost Mustang and Focus RS.

How many reviews does a 2002 Ford Ranger have?

Showing 3 of 1,372 reviews. Regular cab allows for no behind the seat storage. Although its a shadow of all the big trucks on the road, the Ranger is the little engine that could.

When did the Ford Ranger get a V6?

The Ford Vulcan V6 is a 3.0L, 60° V6 engine, first introduced for the 1986 model year and originally designed to be the optional engine in the Ford Taurus and Mercury Sable. In 1991 it became available in the Ford Ranger where it replaced the Cologne 2.9 engine (which it is not related to) as the base V6 in the Ranger

When was the A4LD replaced in a Ford Ranger?

It was replaced by the 4R44E and 4R55E in 1995. The A4LD is a weak transmission, and is known to fail in offroading (4×4) applications.

How much does a 2002 Ford Ranger XLT cost?

The price-leading base edition is the XL Regular Cab Styleside ($12,270) with the 2.3-liter engine, manual transmission, and two-wheel-drive. Add an extended SuperCab, four-wheel drive, and a 4.0-liter V6, and the price climbs to $21,250.

When did Ford Ranger get a new engine?

In 1998 further improvements were made, with a new intake manifold, changes in engine management and cam timing; output was further increased to 155 hp (115 kW) and 185 ft·lbs. A plastic upper intake was added in 2001.

It was replaced by the 4R44E and 4R55E in 1995. The A4LD is a weak transmission, and is known to fail in offroading (4×4) applications.

What kind of automatic transmission does a Ford Ranger have?

A4LD – The C3 was modified into the A4LD 4-speed automatic by adding an overdrive gear, which the C3 lacked. This was the first Ford automatic to use an EEC-controlled torque converter lock-up clutch. Electronic shift control for the 3–4 shift was later added, another first, though other gears remained hydraulic.

How do you change the transmission fluid in a car?

Pop the hood by pulling the engine release lever underneath the steering column. Locate the yellow dipstick that rests above the drain pan. Pull out the dipstick and place a funnel in the tube. Pour in 3 qts. of type H transmission fluid. Replace the dipstick and close the hood. Run the car for 5 to 10 minutes and open the hood again.

What kind of fluid does a Ranger take?

The Ranger takes type H transmission fluid; you can substitute Mercon or Mercon V. Completing regular maintenance keeps the engine lubricated and running smoothly. Neglecting this job can result in costly damage. The maintenance requires only a few tools and about an hour.

What kind of fluid do you use for manual transmission?

• Recommended for all vehicles manufactured by General Motors & Ford (except those with CVTs, or those calling for Type F ATF) including Mercon LV • Recommended for many imports, including Toyota, Lexus, Honda, Acura, Nissan, Mazda, Mitsubishi, Hyundai, BMW, Volkswagen and Audi • Outperforms conventional Transmission fluids Part# VV324

How often do you change the oil in a 2002 Ford Ranger?