How do you replace the universal joint on a Ford Ranger?

Pull the bearing caps out of the drive shaft, using locking pliers. Lift the universal joint out of the drive shaft. Place a new bearing cap onto the outside of the yoke. Place the universal joint into the center of the yoke. Press the bearing cap onto the universal joint, using the U-joint tool.

What’s the best way to replace a U-joint?

With the driveshaft out of the car or truck, the next step is to remove the joint and its bearings. You’ll need to mount the end in a vice, then tap the bearing through far enough to get the joint to drop out. In most cases, a spark plug socket is the perfect tapping tool.

Do you need to replace the universal joint in your car?

A clicking or clunking sound from under your car may indicate a worn universal joint at the drive shaft. Universal joint replacement may seem like a tall task, but it can be done by a novice mechanic with regular tools . The first step in replacing your u-joint is getting at it. To do this, you’ll need to remove the drive shaft.

How does the front axle work on a Ford Ranger?

The front axle uses a locking hub (1983-2000) to lock (connect) the front wheels to the axleshafts. If these hubs are not locked, the wheel will not receive power from the axle. Note: the 2001-2011 4WD Ford Ranger has a live front axle.

Do you need to replace the boot on a Ford Ranger?

Closer look inside says “REPLACE ME!” It’s worth it to do this now, cause its cheap. Apply anti-seize to the back of the spindle and the bore on the knuckle (AFTER you do the joints!). This will make the spindle come off easier later. This is the boot that needs to be released from the inner axle u-joint. Passenger Side (long) shaft.

Where can I get a Ford Ranger ball replacement?

Go to www.harborfreight.com and get one of these. You can also rent them at parts stores. Follow the directions, and its pretty easy. You start with the lower one. Set the receiver cup to let the press push the joint out. do the same with the upper, running the screw through the hole left by the lower one.

How do you replace the axle on a Ford Ranger?

Use a star pattern, and wedge a hard chisels in between for leverage once you get it moving. This is what all your hard work will get you! The spindle is now gone, and you can pull the axle shaft right out. On the passenger side, you need to remove the clamp on the axle boot.

How do you replace the front drive shaft on a Ford Ranger?

Unscrew the nuts, bolts and straps that connect the front drive shaft to the front axle yoke, using a wrench and socket. Slide the drive shaft underneath the front axle while pulling it towards the front of the vehicle. This will separate the splined shaft from the transfer case.

What happens when a universal joint breaks in a truck?

You’ve probably seen it before: a truck on the side of the road, with the drive shaft lying under the vehicle, no longer attached to the transmission or rear axle. This is the ultimate failure mode for a universal joint – literally breaking, and allowing the drive shaft to drop to the pavement, no longer transferring power.

What should I do if my universal joint is failing?

Replacement of the universal joint by a professional mechanic is certainly in order at this point to prevent further damage. Your mechanic should, when possible, select quality replacement u-joints with a grease fitting, allowing for long-term preventative maintenance, and enabling extended life of the u-joint bearings.

How do you install a canopy on a Ford Ranger?

1. Remove the four (4) bolts holding the sports bar feet to the tub as shown. Carefully remove the sports bar from the vehicle and return to the customer with all hardware components. (ref. diagram2). IMPORTANT: You will need to collect and remove the clamp blocks inside the tub at the end of this Step or after Step #35 (when bed liner is removed).

How do you replace the steering wheel on a Ford Ranger?

If your air bags have been used, you will have to install new ones. Turn the Ranger’s steering wheel to its neutral position. Turn the Ranger’s engine off. Open the hood and use a socket wrench to remove the negative battery cable. Allow five minutes to pass for the air bags to disengage. Remove the two screws on the cover of the steering wheel.

Do you need to remove cabin guard on Ford Ranger XL?

Cabin Guards MUST be removed and discarded. For XL vehicles fitted with an after-market Bed Liner that has been cut-out around the Cabin Guard, you will need to remove and discard the Bed Liner, or Fit a new Bed Liner to suit XLT (Non Cabin Guard variant), so the Canopy seals along the front of the tub and prevents any water entering the tub.

How do you replace the universal joint on a Ford Ranger?