How do you remove an airbag module from a Ford Escape?
How do you remove an airbag module from a Ford Escape?
There are 2 ways to do that. You can do it without removing the center console and you can also do it by removing the center console. If you remove the center console you will have more room to reach and remove the airbag module ( air bag module). Even if the dealer tells you that a used Airbag Module will not work they are wrong.
Where is the restraints control box on a Ford Escape?
You find this box on the right side of the center console. Remove the Restraints Control Module fuse from the Smart Junction Box. For the exact location of the fuse, consult the owner’s manual or a Haynes Repair Manual for your particular model year. Place your key into the ignition and turn to the “On” position. Watch the air bag warning light.
Where is the fuse panel on a Ford Escape?
If a fuse blows again contact a qualified service center. The fuse panel is located on the left-hand side kick panel (2001-2004), or on the right-hand side of the center console, by the instrument panel (2005-2007). Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
What happens if you remove the air bag fuse?
If you removed the RCM fuse, the air bag light will remain lit. It will not flash. If it does flash or not stay constantly lit, then you need to replace the fuse you pulled and then pull the correct one. Repeat this process until the air bag light stays continously lit. Turn the electrical system off and remove the key from the ignition.
There are 2 ways to do that. You can do it without removing the center console and you can also do it by removing the center console. If you remove the center console you will have more room to reach and remove the airbag module ( air bag module). Even if the dealer tells you that a used Airbag Module will not work they are wrong.
Why does the airbag light stay on in a Ford Escape?
If you’ve been in an accident, the airbag light is going to stay on until the system has been restored. It will not work until repaired. Here are some common reasons that your Escape’s airbag light could come on. 1. Seat Belts Safety belts are still the most important safety feature in the event your Escape crashes.
Where are the fuses on a Ford Escape?
Fuse box diagram (fuse layout), location and assignment of fuses and relays Ford Escape (2001, 2002, 2003, 2004, 2005, 2006, 2007). Fuses and circuit breakers protect your vehicle’s electrical system from overloading.
What does the diagnostic warning light on the Ford Escape mean?
Every time you start your Ford Escape, the computer system runs a self diagnostic check on all major systems. If any of these checks fail, you will see a diagnostic warning light on the dash for the corresponding system. When the airbag system fails this check, you’ll see the airbag light.
Where are airbag codes stored in Ford SRS?
Below you will find common airbag codes that can be stored in your airbag control module after your vehicle was in an accident. The best part of having your Ford’s original SRS airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play.
Where is the airbag control module located in a vehicle?
Use our airbag control module locator, if you are not sure where the airbag control module is located in your vehicle . Start Your Airbag Module Reset Order Today!
How to remove the SRS airbag control module?
Steps to remove airbag control module 1 First, find the SRS computer module. In most cars, it is under the center console that is between the two front seats, or center of the dash on the floor. 2 Disconnect the positive battery cable and wait 3 min. 3 You are now safe to unplug the airbag control module harness wiring plugs.
How do you install an airbag control module?
All airbag srs components must be installed and connected properly before installing the airbag control module. This includes air bags, seat belts, clock spring and impact sensors. Disconnect the battery and bolt down the module and then connect the harness wiring plugs.
Where is the SRS airbag control module located?
In most GM cars it is under the driver or passenger seat. Disconnect the positive battery cable and wait 3 min. You are now safe to unplug the airbag control module harness wiring plugs. All airbag srs components must be installed and connected properly before installing the airbag control module.
Is it possible to reset an airbag module?
You are now able to re-use your existing airbag module with our reset service! Your module will be restored back to its factory condition and will not require any additional programming. Just Plug & Play! This service is 100% compatible with our seat belt repairs.
