How do you change transmission fluid in a Ford?
How do you change transmission fluid in a Ford?
Place a drain pan beneath the drain hole, remove the plug and drain the fluid. Remove the cooler lines at the transmission and flush them with compressed, low pressure air. Be careful during this step; fluid may shoot from the other cooler line. Place a large drain pan beneath the transmission.
How do you change the transmission in a Ford Explorer?
Put a new gasket on the oil pan and reinstall it on the transmission. Tighten the retaining bolts to 79- to 119-inch pounds with a torque wrench. Replace the cooler lines on the transmission and the drain plug on the torque converter. Return the Explorer to level ground. Remove the dipstick from the filler tube and replace it with a funnel.
How to remove transmission fluid from transmission pan?
1 If the transmission pan has a drain plug, remove the plug to drain the fluid into a collection pan. Use a pan that can… 2 If you need to remove the entire transmission fluid pan, unscrew the two upper-most bolts halfway, then unscrew the… More …
Where is the transmission fluid located in a car?
For rear-wheeled vehicles, the transmission typically hangs under the center console area, facing front to rear. Examine the pan. In most vehicles, you’ll be able to drain the transmission fluid by removing a drain plug in the center of pan and letting the fluid drain out into a receptacle.
How do you change transmission fluid in explorer?
Hold the transmission pan in place, and install the pan mounting bolts hand-tight. Tighten the transmission-pan bolts gradually, following a crisscross pattern, using the ratchet, ratchet extension and socket. Torque the transmission-pan bolts to 71 to 119 inch-lbs. using a torque wrench.
How do you remove oil filter from Ford Explorer?
Lower the pan carefully over the drain pan and tilt the transmission pan to drain the rest of the oil. Then remove the transmission pan and gasket from the Ford Explorer. Unbolt and remove the filter from under the transmission using a ratchet, ratchet extension and socket. Also, remove the O-ring from the filter fitting if equipped with it.
How do you change oil in an explorer?
Support the oil pan in place by hand, using one or two shop towels to shield yourself from the hot surface, and finish removing the rear-pan bolts using the ratchet extension and socket. Lower the pan carefully over the drain pan and tilt the transmission pan to drain the rest of the oil.
What kind of fluid does Ford Explorer use?
Ford Mercon V is the fluid required for this transmission. In this video I show you how to fill and adjust the 5R55S after a repair that has required a fluid drain or loss. If you follow this procedure you will have no issues with the proper fill level of the 5R55S.
Is it OK to change transmission oil on an old car?
Mechanics say it is not recommended, unless it has been changed regularly before. The reason is that the new oil will loosen up old deposits that would then disrupt the function of the gears. So, think twice before changing the transmission oil on an older car. Thanks! I have a 1995 GMC Suburban and my transmission is slipping.
How do you remove oil pan from transmission?
Place a large drain pan beneath the transmission. Loosen the retaining bolts on the oil pan with a socket wrench until they are within a few turns of removal. If the seal doesn’t break on its own, gently tap it with a rubber hammer. Fluid will drain from the edges of the pan. Remove the pan retaining bolts when the fluid stops draining.
How much oil to put in transmission fluid?
Insert the dipstick fully again in its tube and pull it out. The oil level should be in the cross-hatched area of the dipstick. If you have to, add transmission oil in increments of a half-pint (0.24-liters) to avoid overfilling the transmission.
How do you change the transmission fluid in a Ford F-150?
Returning the pan to its original position. In order to perform this task, pop the hood and remove the transmission fluid dipstick. Next, use the funnel to distribute approximately 5 to 6 quarts of brand new transmission fluid.
How do you change the oil in a transmission?
Place a drain pan underneath the transmission oil pan. Using a ratchet, ratchet extension and socket of the appropriate size, begin to loosen and remove the side and front bolts from the oil pan. Be careful, as hot oil might begin to flow out of the pan as you finish removing the bolts.
How to change the oil in a Super Duty truck?
Park your Super Duty on flat, level ground. Start your vehicle and let the engine and transmission warm up, if you have not driven the truck just prior to the oil change. Then turn off the engine. Set the transmission to neutral (N), raise the front of the truck with a floor jack, and support it on jack stands.
How much new transmission fluid do you need?
Next, use the funnel to distribute approximately 5 to 6 quarts of brand new transmission fluid. In order to test the new fluid, you will need to heat your transmission back up to operating temperature (approximately 150°).
Can you change the filter on a Ford transmission?
Note that Ford does not recommend ever changing the filter. being clogged. Don’t buy a new pan gasket. The original is reusable. clamp, sized to fit over your cooler hose. There have been different size cooler lines over the years, so check before buying! those, too. your pan has a drain plug. If you are not changing the filter, jump to step 4.
How to change automatic transmission fluid in Ford Ranger?
Discard the old pan gasket. 6. If necessary, remove the Automatic Transmission Fluid (ATF) filter mounting bolts, then remove the filter by pulling it down and off of the valve body. Make sure any gaskets or seals are removed with the old filter. The transmission usually has one round seal and a rectangular gasket.
How often do you change automatic transmission fluid?
Automatic transmission fluid is used for many purposes inside your transmission, such as cleaning, shifting, and cooling. It’s very important the fluid remains clean, or wear can quickly occur. Check your fluid level and condition every 30,000 miles.
How do you change oil in a Ford Ranger?
Take the bolts out of the bottom of the transmission pan but leave two bolts in the front engine side partway in to keep the pan from falling. Remove the last two bolts while holding the pan and tip it slowly in the rear to pour out the oil. Once the oil is out, clean the pan and the magnet inside the pan with carburetor cleaner and a soft rag.
