How do I program my rc122 spectrum remote?

How do I program my rc122 spectrum remote?

Programming Your Remote

1. Turn on the device, such as your TV, that you want the remote to operate.
2. On your remote, press the corresponding device button [such as TV, DVD, CBL] and the SELECT/OK buttons simultaneously until all the device buttons blink twice.
3. Point the remote at the device and press 9 9 1.

How do I program my Time Warner Cable remote?

Programming Your Remote

1. Turn on the TV you want to program.
2. Press and hold the Menu + OK buttons simultaneously until the Input button blinks twice.
3. Press TV Power. The Input button should light up solid.
4. Aim the remote at your TV and press and hold the UP arrow.
5. Once the device turns off, release the UP arrow.

What are the codes for spectrum remote?

Program Spectrum Remote — Universal CLIKR-5: UR5U-8780L / 8790L

How do I program my Time Warner remote to my DVD player?

How to Program a Time Warner Universal Remote to a DVD Player

1. Turn the DVD player on.
2. Press “DVD” on the remote.
3. Hold down the remote’s “Setup” button until the “DVD” button blinks twice.
4. Enter the code “9 9 1” using the number buttons on the Time Warner remote.
5. Aim the Time Warner remote at the DVD player.

How do I reset my Time Warner remote control?

Solution 5: Resetting Spectrum Remote to Factory Defaults

1. Press and hold the TV button.
2. While you are still holding it, press the OK button for 1 second and then release both buttons at the same time.
3. Now you have to press and hold the Delete button for 3 seconds.
4. Now your TV remote will be reset to factory settings.

How do I control my Soundbar with my cable remote?

Control Your Soundbar with a Remote: Universal Steps

1. Find the compatible connection for both devices. The connection ports are usually found at the back of your devices, or occasionally on the side.
2. Connect the corresponding cable to both devices.
3. Turn on Both Devices.
4. Adjust the Settings.

How do I get my SoundBar to turn on with my TV?

To make your Soundbar turn on with your TV when using an optical cable connection, follow these steps:

1. Plug in the optical cable.
2. Ensure that Auto Power Link is turned on.
3. Turn on the D.IN mode on your Soundbar.
4. Adjust the TV speaker settings.
5. Plug in the HDMI ARC connection.
6. Ensure that Anynet+ is turned on.

How do I get my spectrum remote to control volume?

Press the “CBL” button at the top right of your remote. At the same time, press and hold the “OK” or “SEL” button for a few seconds, then release both buttons at the same time. The “CBL” button will light up and stay illuminated. Press the “VOLUME DOWN” button once, and then press your TV button.

Where is the reset button on Spectrum box?

Locate the Reset button on the front or back of your cable box. Check along the front side of your cable box for a small circular button labeled Reset. If you don’t see the button on the front side of your cable box, then check on the back panel near the power cords.

How do you reprogram a spectrum remote control?

Note: To reprogram your remote for the Spectrum Receiver press and hold the CBL and OK/Select buttons simultaneously until all device buttons blink twice then enter the code that matches your Spectrum Receiver. Turn on your device.

How do I return my Remote to its original settings?

Follow these steps in order to return the remote back to its original settings: Press and hold “SELECT/OK” and “CBL” until all device keys blink twice. Enter 9 8 1. All device keys will blink 3 times. After few seconds the “CBL” key blinks twice.

What are the codes for Philips spectrum remote controls?

4 digit codes for Philips RC122 Spectrum remote controls. Spectrum codes: 3 digit 4 digit 5 digit. Most models RC122 AT8560 Cisco DTA. Four digit TV, Audio, DVD, VCR, DVR, HTiB and Cable Box codes for Philips RC122 Charter Spectrum (former Time Warner) universal remote controls.