Can a dash pad be removed from a corvette?
Can a dash pad be removed from a corvette?
Two screws hold in the top of the instrument cluster to the dash pad. These must be removed to remove the dash pad. Two bolts hold the bottom of the instrument cluster in place. These do not require removal unless you need to remove the dash cluster after dash pad removal.
How do you remove the dash flasher on a corvette?
The four way flasher button pulls off with a couple of small screwdrivers prying it outward. The tool is in place from the underside of the dash ready for the screwdriver to push the tab from the bottom up. Once the flasher is out of the plastic housing it must be coerced over enough to remove the connector.
Where are the sensors on a Corvette dash?
There are two sensors, sun load and ambient light, one on each side. Remove the two 7mm screws at the top of the dash. Remove the7mm screw on the right side of the dash near the door jamb. Pop off these access covers inside the glove box with a flathead screwdriver to access the screws behind them.
How do you remove photo sensor from Corvette?
Remove the 7mm screw on the left side of the dash. Pop up the defroster vent with a flathead screwdriver to access the photo sensor. Gently twist the connector to remove it. There are two sensors, sun load and ambient light, one on each side. Remove the two 7mm screws at the top of the dash.
Two screws hold in the top of the instrument cluster to the dash pad. These must be removed to remove the dash pad. Two bolts hold the bottom of the instrument cluster in place. These do not require removal unless you need to remove the dash cluster after dash pad removal.
Where can I buy a new Corvette dashboard?
If you notice your stock dashboard has seen better days, browse the Top Flight Automotive online store for dash pads preferred by Corvette restoration specialists. The days of purchasing a used factory dashboard from a previous owner are over as Top Flight Automotive replacements fit the C1, C2, C3, C4 and C5 generations.
The four way flasher button pulls off with a couple of small screwdrivers prying it outward. The tool is in place from the underside of the dash ready for the screwdriver to push the tab from the bottom up. Once the flasher is out of the plastic housing it must be coerced over enough to remove the connector.
There are two sensors, sun load and ambient light, one on each side. Remove the two 7mm screws at the top of the dash. Remove the7mm screw on the right side of the dash near the door jamb. Pop off these access covers inside the glove box with a flathead screwdriver to access the screws behind them.
How big is the tab on a Corvette dash?
The leg that pushes down on the tab is ½ inch long, the space between the long portion of the tool and the tab that pushes down is 5/8 inch. The long leg is 5-1/2 inches long and the portion to pull downward on is 2-3/4″ long.
How do you remove the radio from the dash?
Push the radio forward; drop the end down, and rotate the radio assembly to remove it from under the dash. The heater control is held in place from the back side of the dash by two retainers, one on each side, as shown in photo #6.
How do you remove the dash trim cover?
Step 1: Remove the dash trim cover. The dash trim hides the mounting brackets for components such as the radio and the AC control module. This will need to be removed to gain access to the AC control module. On some vehicles this trim is able to be pried off gently with the plastic trim tools.
How do you remove the dash from a corvette?
Pull the panel up and towards the front of the car. Notice that there is a connector, two 10mm hex head bolts, and an auxiliary power port connector to remove from this area. Open the console door and locate the two plastic inserts covering the 10mm nuts. Pry them off with the plastic wedge. Remove the 10mm hex head nuts with a 10mm socket.
How do you remove a negative capacitor from a car?
Use a wrench to remove the negative cable, which is usually covered with a black cap and marked with a minus sign, from the terminal. Warning: Erasing codes by disconnecting your vehicle’s battery can also clear out the memory for your radio and other onboard components. Drain any remaining electricity from the capacitor.
Where is the turn signal on a corvette?
Push down on the blue plastic tab to remove the connector from the A/C control panel. Next, remove the two screws holding the factory stereo in place. Disconnect the two electrical connectors and the antenna to free the stereo. The turn signal / hazard switch is located at the top of the carrier.
How to remove the air cleaner from a corvette?
Remove the four metal screws attaching the (S) tube or metal duct from the radiator support. Remove screws that attach the air cleaner body to the inner fender well, these screws bolt through the fender well and are accessible in the left wheel well opening. Hood, Radiator and Shroud
Can you remove the dash pad from a corvette?
It can be done without removing the dash pad through the shift console plate, but it is much easier to access for removal and install through the passenger side dash entrance created. At this point the center dash bezel is ready to be removed. To remove this bezel you must be careful not to break the tiny corners where the bezel is thin.
Where do you remove the hood on a corvette?
Hood, Radiator and Shroud A. Hood – Removal of hood should be at hood latches located toward the front of the car. Remove bolts, which are located on the hood itself. After removal, complete latch assembly should still be attached to the inner fender wheel skirt.
What is part number on Corvette air conditioner?
The A/C accumulator acts as a filter; if the A/C system is opened, moisture can enter the system and cause havoc. To order a replacement, use part number 455034. This compressor has an obvious leak, but keep in mind that compressor troubles may not always be this straightforward.
