Where to replace serpentine belt on Mercury Sable?
Where to replace serpentine belt on Mercury Sable?
To maintain engine performance, replace the serpentine belt in your 2002 Mercury Sable owners when it wears down. Attach a 15 mm wrench to the bolt in the center of the tensioner pulley. The tensioner pulley is located in the middle of the crankshaft and water pump pulleys.
How do you remove a serpentine belt from a Chevy Silverado?
In order to remove the belt from the pulleys, you will need to release this tension, which will slacken the belt and allow you to remove it from the rest of the pulleys. There should be a 3/8-inch drive square hole in the middle of the tensioner.
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
Where do I find the serpentine belt on my car?
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
In order to remove the belt from the pulleys, you will need to release this tension, which will slacken the belt and allow you to remove it from the rest of the pulleys. There should be a 3/8-inch drive square hole in the middle of the tensioner.
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
How often should a serpentine belt be replaced?
Without this belt, the engine cannot function correctly. It is recommended that the belt be checked every 6,000 miles or six months, and replaced when necessary. Figure 1. Shredded serpentine belt.
Do you need a serpentine belt on a Chevy Silverado?
This article applies to the Chevrolet Silverado GMT800 (1996-2006). If you didn’t already know, the serpentine belt or drivebelt on your truck’s engine is very important in the proper operation of the engine.
How to replace serpentine belt 02-09 Chevy Trailblazer?
(Playback ID: QQhz5bxZ9sEf6333) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later.
Without this belt, the engine cannot function correctly. It is recommended that the belt be checked every 6,000 miles or six months, and replaced when necessary. Figure 1. Shredded serpentine belt.
This article applies to the Chevrolet Silverado GMT800 (1996-2006). If you didn’t already know, the serpentine belt or drivebelt on your truck’s engine is very important in the proper operation of the engine.
(Playback ID: QQhz5bxZ9sEf6333) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later.
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
How do you tighten a serpentine belt on a car?
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
How many pulleys does a Mercury Sable have?
Return the tensioner pulley to its original position and remove the belt from the remaining pulleys. The 2002 Mercury Sable has seven pulleys in the serpentine belt system. Wrap the replacement belt around the all of the pulleys except the tensioner pulley.
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
What happens if a serpentine belt goes bad?
The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function.
To maintain engine performance, replace the serpentine belt in your 2002 Mercury Sable owners when it wears down. Attach a 15 mm wrench to the bolt in the center of the tensioner pulley. The tensioner pulley is located in the middle of the crankshaft and water pump pulleys.
Return the tensioner pulley to its original position and remove the belt from the remaining pulleys. The 2002 Mercury Sable has seven pulleys in the serpentine belt system. Wrap the replacement belt around the all of the pulleys except the tensioner pulley.
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
