What vehicles have a 9 inch rear end?

Common applications

1957-1986 Ford F-100 & F-150.
1958-1960 Edsel (All series including Wagons)
1976-1980 Ford Granada.
1976-1979 Lincoln Versallies.
1957-1970 Ford Fairlane.
1957-1971 Ford Thunderbird.
1964 1/2-1973 Ford Mustang.
1966-1983 Ford Bronco.

What is a 9 inch rear?

The Ford 9-inch rear end, so named because of its 9-inch ring gear diameter, was manufactured from 1957 to 1987 by the Ford Motor Company and installed in some intermediate and most full-size Ford, Lincoln, and Mercury passenger cars, F-Series ½-ton trucks, and Econoline vans.

Why is Ford 9-inch rear end so popular?

The Ford 9-inch is desirable because it has a removable carrier, which allows quick rear end changes. Many racers carry an extra carrier assembly with a different rear end ratio so they can try different combinations on the same day while at the track.

What is special about a Ford 9 inch rear end?

The 9-inch Ford Rearend is the Strongest Rearend Out There—It’s All Due to “Hypoid Distance” 1] The 9-inch Ford has no differential case gear-ratio range restrictions; one differential accepts all gear ratios from the 2s through the 6s.

Are there axles in 8 ” and 9 ” rear ends?

Yes that is true the 28 spline axles are the same in a 8′” and a 9″! I used a 28 spline Mavrick 8″axles in my 78 cobra II when i switched to a 9″ housing. They should..I just had the axles out of my 68 mustang 8 inch and they appeared identical to the 69 cougar 9 inch axles that are standing in the corner of my garage… Yes it is true.

Can you remove an axle from a 9 inch Ford?

You cannot remove 1″, 2″, or 3″ from any stock Ford 8″ or 9″ axle. -Axles are always measured from the outside of the axle flange to the end of the splines. -Most small bearing 8″ and 9″ Fords have a 2 1/2″ brake offset. -Most big bearing 9″ Fords have a 2 3/8″ brake offset.

How to narrow a 9 inch Ford rear end housing?

ALWAYS measure a rear end from the outside of the axle flange to the outside of the axle flange. -28 spline 8″ and 9″ Ford axles are the same spline. -You have to cut at least 4″ out of 8″ or 9″ Ford OEM axles in order to shorten and re-spline them. Some of the older axles cannot be shortened at all.

What kind of axle shafts do you need for a Ford 9?

But frankly, if you’re going to drop the coin on this thing, you should also be upgrading to at least 31 spline axle shafts. The 28 and 31 spline lockers cost about the same and 31 spline shafts will give you a significant strength upgrade.

When did the Ford 9 inch rear axle come out?

The Ford 9 inch rear end. Ford’s 9 inch rear axle was produced from 1957 through 1986. At one time or another, it was installed in nearly every Ford passenger car and truck. In racing and hot rodding today, you’ll find these rear ends and their aftermarket descendants in just about everything—not just Fords.

Can a broken rear end be replaced with a better front axle?

Make sure the answer is yes by replacing your stock or broken rear end or front axle assembly with something better. We’ve got universal and direct-fit assemblies, including beefy Ford 9-inch, Dana 44 and 60, GM 8.875-inch, and many others.

What vehicles have a 9 inch rear end?