Is there no power to my coil or to my fuel pump?

Still no power seems to go to either one of those plugs. on the bike. I do have the kill switch in the on posistion. and my bike is in neutral… The starter turns fine.. I havent dug deeper into the fuse block location yet,,, to see if I have a wire that is not where it should be…. or whatever my ole eyeballs can determine…

Where to check for no start fuel pump?

The first thing you want to do is check the fuse panel to see if the fuse is blown. If your car has two fuse panels than the one in the engine compartment; should be the correct one to check. The fuse panel or circuit box is usually located near the battery; and is a small black box with a removable lid.

Why does my fuel pump only run for a few seconds?

This sound is the electric fuel pump trying to prime the fuel system. It will only run for a few seconds and then shut off. If you are not sure you could hear it or if there is noise outside; you may have to try it several times. Turn the key on and wait then turn it off.

Why does fuel gauge read wrong after fuel pump replaced?

Fuel gauge reads wrong after fuel pump replaced – YouTube If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN. There is an option for a anti-slosh module that could cause you If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN.

Where does the coil go when you replace the distributor?

Lacey, when you say you replaced the distributor does that mean the entire assembly – drive shaft and all, or just the rotor or maybe just the distributor cap. If this is an H.E.I. system then the coil is most likely to be located on top of the distributor cap.

How does an electric fuel pump keep cool?

Electric fuel pumps run continuously with your engine, delivering high-pressure fuel to the fuel rail and injectors. Fuel pumps keep cool by staying submerged in fuel. If you make a habit of running your tank all the way to empty before filling up; your fuel pump will most likely die before its designed lifespan.

Why is the fuel pump and relay not working?

The ignition circuit, which includes the ignition switch, controls power to many components, including the fuel pump and relay. If there is an issue with the switch or the circuit, perhaps a wiring problem, then power to the fuel system may be cut off.

What should fuel pressure be when no Buzz?

Fuel pressure is typically in the 35 to 45 psi range. If your Anti-Theft light is flashing; the anti-theft system is disabling the fuel pump to prevent the engine from starting. Bad fuel pump (Pump should run for a few seconds when ignition key is turned to start, no buzz means no fuel delivery to the engine).

What to do if your fuel pump quits?

There is only a two second prime until the truck starts, then once oil pressure is up, the computer will send constant power to the fuel pump. Sometimes just unplugging, cleaning and re-connecting the connector will fix the problem. If you do have power, I would suspect the fuel pump quit.

Where is the fuse for the fuel injector located?

Blown injector circuit fuse Bad fuel injector power relay A fault in the wiring harness to the injectors So, the injector fuse and relay are usually located; in the relay box or power distribution center in the engine compartment. Fuses are used to protect various electrical circuits, while supplying power to components.

How does the fuel pump work in a car?

The ECM activates the fuel pump for several seconds after the ignition switch is turned on to improve engine startability. If the ECM receives a engine speed signal from the crankshaft position sensor (POS) and camshaft position sensor (PHASE), it knows that the engine is rotating, and causes the pump to operate.

What to do if no power at fuel pump?

Firstly, make yourself up a ‘jumper’ cable out of a short length of wire and two spade connectors and simply bridge the two pins on the relays circuit side (that’ll be the two bigger pins on the relay with thicker wire on the underside of the relay board if you’re not sure) and see if the car starts.

Which is the power switch for the fuel pump?

The first is for the low speed fan, the second is for the fuel pump operation and the third (which is out there on its own) is the main power switch for the various sensors required to run the engine and it is this relay that you should bridge first.

Why is my fuel pump going so slow?

Slow crank, battery and connecters good. It is unlikely that an oil leak would have any impact on the slow cranking you describe. Generally, slow cranking is related to a weak battery or charging system. It sounds like you may have a weak battery, a failing…

What to do if your fuel pump is not working?

Easy way to eliminate spark problem from fuel problem is to remove air filter and squirt some gas in intake while spinning starter. If it fires, you know it’s a fuel problem, not spark. “The last few days,, I have been trying to track down,, why I might not have power 12v. wise going to my two plugs.

What to do if there is no spark or fuel?

If there is no spark or fuel, then the first thing I would do is check the vehicle’s fuses and relays, particularly the EFI main and ignition relays. It may be possible that one of these components has failed and is cutting off power to the vehicle’s ignition and fuel systems.

Why does my car not start when I crank the engine?

It may be possible that one of these components has failed and is cutting off power to the vehicle’s ignition and fuel systems. If these check out, then it may be possible that the issue is wiring-related, in which case I would carefully examine the engine bay for any worn, frayed, or otherwise potentially faulty wiring.

Why does my car not start when I Turn on the ignition?

The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter). However, the source may also be a mechanical fault (for example, a leaking valve), or faulty components in other systems.

What to do if your fuel pump won’t start?

Use a circuit tester to check all the electrical connections to the fuel pump. Turn the key to ON. If you see a current, then it is not the pump. If there is no current, check the fuse.

What makes an internal combustion engine not start?

To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition). The lack of any of these three things will prevent your engine from starting.

Is there no power to my coil or to my fuel pump?