How do you replace the ignition switch on a Dodge Ram?

Use a T25 Torx screwdriver to remove one screw underneath the tilt lever mechanism. Then, use the T20 screwdriver to remove one screw underneath the ignition switch. Figure 6. Remove the tilt lever assembly screws. Pull back on the red tab of the rear ignition switch connector, and unplug it from the dash wire harness.

Why is the ignition switch on my Dodge Grand Caravan not working?

The Dodge Grand Caravan has also has a problem with the wafer material inside the ignition switch getting bent and causing the switch to be locked and unable to move. You can easily replace the switch to repair the problem and have your vehicle operating properly.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

How do you remove a battery from an ignition switch?

Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.

What kind of ignition switch does a Dodge Ram 1500 use?

Select your Year, Make, Model and Engine to find those that fit your vehicle. With adequate power and ability, your Dodge Ram 1500 is the pick-up truck that simply gets the job done. What doesn’t get the job done or even start your Ram 1500 is a worn-out ignition switch. Replace it with a new Dodge Ram 1500 ignition switch from AutoZone today.

How to replace ignition lock switch in Dodge Caravan?

This helpful video details the replacement of a faulty ignition lock switch in a Dodge Caravan. In step-by-step detail, the steering column and instrument panel covers are removed to access and remove the lock-switch. A rebuilt switch is then installed.

How do you replace an ignition switch on a car?

Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.

Can a bad ignition switch keep a ram from starting?

A bad ignition switch can cause your Ram not to start at all. And, it can keep your Ram from starting in a couple of different ways. The first is when the starter cranks, but the bad ignition switch doesn’t turn on the fuel pump or ignition. The engine will just turn over with no spark. The second way is when the starter doesn’t turn at all.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

Can a rusty ignition switch keep a Ram 1500 from starting?

The last thing you want is for your Ram 1500 to be stuck on a jobsite, unable to start. When your ignition switch becomes rusty or faulty, it no longer transmits a signal to turn your truck on. Instead of being stuck with this problem, consider a new ignition switch for Dodge Ram 1500, affordable and available at AutoZone.

What happens if you have a bad ignition switch?

The most noticeable symptom of a bad ignition switch is stalling. Your Ram stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back.

How do you remove a tilt lever ignition switch?

The ignition switch is held in place by two Torx screws and mounted behind the tilt lever mechanism. Use a T25 Torx screwdriver to remove one screw underneath the tilt lever mechanism. Then, use the T20 screwdriver to remove one screw underneath the ignition switch. Figure 6. Remove the tilt lever assembly screws.

What’s the name of the ignition lock cylinder?

The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road…

Can a faulty ignition lock cylinder cause problems?

When the ignition lock cylinder has issues it can cause problems with powering on and starting the vehicle. Usually a faulty ignition lock cylinder will produce a few symptoms that can alert the driver of a potential issue.

How do you replace spark plug on Dodge Ram?

Check that the new spark plug is gapped correctly at 0.040″. Apply a small amount of anti-seize onto the spark plugs threads. Start threading the spark plugs into the hole by hand with an extension and torque to 15 ft. lbs. Slide the coil packs spark plug boot wires onto the top of the spark plugs.

Where is the ignition sensor on a Dodge Ram?

This sensor is located on the backside of the resonator box near where the intake pipe mounts. Then, remove the two 10mm bolts at each side of the box. Pull up on the box to release it from the engine, but do not remove it from the engine bay. On the backside of the box is a crankcase vent hose that needs to be removed.

What should I do if my ignition switch is not working?

Keep pressing it in until you hear the click of the release pin setting into place inside the steering column. If you don’t hear a click from the release pin, the ignition switch isn’t properly seated yet. You may need to push in on the switch a little to make it click into place. Helpful? Reconnect the battery and test the new switch.

Can you replace the ignition switch on a Dodge Caravan?

You can easily replace the switch to repair the problem and have your vehicle operating properly. Detach the negative battery cable from the battery of your Dodge Grand Caravan with an open-end wrench and move the cable out of the way.

How to fix ignition problems by replacing the ignition switch?

How to fix ignition problems by replacing the ignition switch. Ignition switch location, inspection, removal and repair. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Screwdriver set: http://amzn.to/2j92UCG 2. Disposable Gloves: http://amzn.to/2zSRuxO 3. Common Sense 4. Full HD Camera: http://amzn.to/2AvoEk7 5.

What’s the Accessory position on an ignition switch?

Insert the key and turn it to the “accessory” position. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).

Luckily, replacing the ignition switch in your Dodge Ram is a relatively simple process….Dodge Ram 2002-2008: How to Replace Ignition Switch

Step 1 – Disconnect the battery.
Step 2 – Remove the steering column panels.
Step 3 – Remove the ignition switch.
Step 4 – Install the new ignition switch.

What happens when the ignition switch on a Dodge Ram goes bad?

Your Ram stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies If your Dodge Ram is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad.

How do you remove the rear ignition switch?

Remove the tilt lever assembly screws. Pull back on the red tab of the rear ignition switch connector, and unplug it from the dash wire harness. Then pull back on the tab of the front switch connector, and unplug it to release the ignition switch from the lock cylinder.

What are the symptoms of a bad ignition switch?

Your Dodge Ram ‘s ignition switch is one of the most vital items on the entire vehicle. If it fails, the entire vehicle won’t be able to run. We’ve compiled some of the most common symptoms of a bad ignition switch. These include stalling issues, not starting, and no power to the radio or accessories.

How to remove the ignition switch without a key?

How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.

What is the wiring diagram for a Dodge Ram?

Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2002-2003 Dodge Ram . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle.

Where is the disarm wire on a Dodge Ram?

NOTE #7; the DIESEL tach wire is a GRAY/BLACK in the BLACK plug at the PCM (Powertrain Control Module) NOTE #8: the DISARM wire requires a (-) Negative thru a 480 Ohm Resistor and an extra relay part #775, to connect, See DIAGRAM

How do you remove ignition switch from car?

Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

How do you replace the ignition switch on a Dodge Ram?