What does p0058 mean on a Dodge Charger?

P0058 DODGE Meaning Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

What does a P0158 code on a sensor mean?

A P0158 code means that the voltage was higher than normal on the signal circuit. NOTE: A post-catalyst o2 sensor will normally switch slower and fewer times than front (pre-cat) o2 sensors.

What causes a p0058 heater control circuit high?

Potential causes of a P0058 code include: Open in the heater control circuit (12 volt PCM controlled systems) Short to B+ (battery voltage) in the heater control circuit (12 volt PCM controlled systems) Open ground circuit (12 volt PCM controlled systems) Short to ground on heater control circuit (On PCM ground controlled systems)

Is there a p0134 code on my O2 sensor?

3 replacements of O2 sensor and still have P0134 code. Now told it is the PCM – Maintenance/Repairs – Car Talk Community 3 replacements of O2 sensor and still have P0134 code. Now told it is the PCM I have a 2002 Chrysler T&C limited.

What does the p0734 code in the Check Engine light mean?

A P0734 trouble code indicates that an abnormality has been detected in the gear ration of one of the automatic transmissions gears, causing the storage of a code in the Powertrain Control Module (PCM) and illumination of the Check Engine Light. Related codes include P0729, P0730, P0731, P0732, P0733, P0735, and P0736. What the P0734 code means

What is the trouble code for cylinder 3?

All our repairs are backed by our 12-month / 12,000-mile warranty. P0303 is a generic diagnostic trouble code (DTC) indicating an issue with the firing of cylinder 3. This code may be seen with other misfire codes as well as lean / rich condition codes. The P0303 DTC is set when the ECU detects multiple misfires from cylinder 3.

What causes fuel pressure sensor to set code p0088?

Defective fuel pressure sensor (Note that while a defective sensor could possibly set code P0088) it is more likely to deactivate the pump than to cause a high fuel pressure condition. In practice, it is more common for defective fuel pressure sensors to set low fuel pressure related codes.) What are the symptoms of code P0088?

What to look for in a Ford p0069 code?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P0069 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does sine code p0088 stand for?

Sine code P0088 indicates an excessive fuel pressure the problem is unlikely to be caused by wiring issues, unless the fuel pressure regulator is electrically operated. In some applications the pressure regulator is located on the fuel rail and operated by a spring with vacuum assistance obtained from the inlet manifold.

What causes an engine to have a P0158 code?

Potential causes of an P0158 code include: Bad o2 sensor (Bank 2 Sensor 2) Wiring in contact with exhaust components. Engine running rich (If other codes are present) Holes in exhaust causing PCM to over-rich engine resulting in an abnormally high Bank 2, sensor 2 reading.

What is the OBD code for a Dodge Ram 1500?

I bought a 2006 dodge ram 1500 with the 5.9 l hemi. I replaced one of the catalytic converters due to it being hollow and after I started the truck and the codes p0038 and p0058 and it stutters when racing up the engine…. I am getting the OBD codes p0032, p0038, p0052, and p0058.

What are the symptoms of a P0158 DTC?

Symptoms of a P0158 DTC may include: MIL (Malfunction Indicator Lamp) on Engine loses power and misses intermittently May exhibit loss of fuel efficiency Potential causes of an P0158 code include: Wiring in contact with exhaust components Engine running rich (If other codes are present)

How much does it cost to repair a p0058 Dodge?

The cost to diagnose the P0058 DODGE code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does a p0750 mean for a Dodge Ram?

The TCS does this to protect the transmission from further damage. P0750 is an electrical fault and does not mean the transmission has mechanical damage. The transmission solenoid/TRS assembly, called a “solenoid pack” must be replaced as a single component.

What does trouble code mean on Dodge Ram?

One of the most common problems with the Dodge Ram is when it throws the P0700 trouble code. A trouble code is a code thrown out by an automatic transmission whenever it detects in the Ram that there is an issue that needs your attention. In the case of the P0700, it is a general code.

What does the p0058 code on the oxygen sensor mean?

What the P0058 code means. When this code is stored in the powertrain control module it means that the heater control circuit in the oxygen sensor after the catalytic converter on the cylinder bank not containing cylinder one has higher voltage than expected.

What is the p0032 code on a Jeep Wrangler?

I have an ’06 Jeep Wrangler w/4.0l, and at random intervals it throws the following 4 codes: P0032, P0038, P0052, and P0058. They’re “heater control circuit high” for all 4 O2 sensors.

What do you need to know about Dodge code p0058?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P0058 DODGE code is 1.0 hour of labor.

What are the trouble codes on a Dodge?

1 Dodge Codes 2 Trouble Code 3 P0171 4 P0300 5 P0301 6 P0340 7 P0420 8 P1000 – P1099 (Fuel and air metering and auxiliary emission control) 9 P1200 – P1299 (Fuel and air metering – injector circuit) 10 P1300 – P1399 (Ignition system or misfire)

I have an ’06 Jeep Wrangler w/4.0l, and at random intervals it throws the following 4 codes: P0032, P0038, P0052, and P0058. They’re “heater control circuit high” for all 4 O2 sensors.

What are the symptoms of a p0038 DTC?

If the PCM detects an abnormally high voltage condition on the heater circuit, P0038 may set. This code is only referring to the heating circuitry half of the Oxygen sensor. Symptoms of a P0038 DTC may include: MIL (Malfunction indicator lamp) illumination There would likely be no other symptoms.

How does the ECM work on a Dodge?

The ECM controls the heater element circuit by allowing current flow to ground. The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications. Need more information on how to fix the P0058 DODGE code?

Why is the p0058 code stored in the Powertrain Control Module?

When this code is stored in the powertrain control module it means that the heater control circuit in the oxygen sensor after the catalytic converter on the cylinder bank not containing cylinder one has higher voltage than expected. What causes the P0058 code?

What does p0058 mean on a ho2s heater?

P0058 is a diagnostic trouble code (DTC) for “HO2S Heater Control Circuit High (Bank 2 Sensor 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.

When is the p0038 Dodge code detected?

When is the P0038 DODGE code detected? Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

What does p0058 mean on a Dodge Charger?