What is the code for the airbag light?

Code 21 (double flash, pause, one flash) means the diagnostic monitor is not mounted properly.

What does the code 13 on an air bag mean?

Code 13 (single flash, pause, three flashes) means that the airbag circuit has shorted to ground and Code 14 (single flash, pause, four flashes) means that the primary crash sensor circuit has shorted to ground. These codes are signaled by two flashes, a two-second pause and the number of flashes that corresponds to the second digit.

Is the SRS warning light an air bag code?

These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light. This is a computer controlled system designed to deploy one or more driver, passenger, and side airbags. How to read air bag codes ?

What does Code 51 mean on Ford airbag?

Code 51 (five flashes, pause, one flash) means the airbag diagnostic monitor’s internal fuse is blown, Code 52 (five flashes, pause, two flashes) means the back-up power supply has had a voltage boost fault and Code 53 (five flashes, pause, three flashes) means the front crash sensor has high resistance or the diagnostic monitor has failed.

Where are airbag codes stored in a Chevy?

Below you will find common airbag codes that can be stored in your airbag control module after your vehicle was in an accident. The best part of having your Chevy’s original airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play.

What is the DTC code for a airbag module?

Third Row Left Roof Rail Deployment Loop Resistance Above Threshold Third Row Left Roof Rail Deployment Loop Resistance Below Threshold Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS) Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS)

Can a Chevy airbag be reset by myairbags?

The best part of having your Chevy’s original airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play. No additional programming of the VIN is required to fix your airbag codes.

Why do I need to reset my Honda airbag module?

Even after a minor accident the airbag may not deploy but the seat belts will lock and airbag module will need to be reset because of crash data and crash codes that are stored in the airbag module. MyAirbags will reset your airbag control module back to its original manufacturer state clear of all codes, both soft and hard codes.

Why does my airbag light flash on and off?

After continued use, the thin circuit bands that make up your airbag clock spring may become brittle or worn out. This leads to a sporadic connection of your driver’s airbag. If this is the case, the system will send a code to your computer and the airbag light will turn on or flash.

How do you know if your airbag is working?

Because airbag problems range from a lost battery feed to a shorted circuit, it is important to understand the codes so that the airbag can be properly repaired. These codes are started by a single flash of the indicator light, followed by a two-second pause.

What does code 13 mean on airbag light?

How do you find the airbag light code?

These codes are signaled by three flashes, a two-second pause and the number of flashes that corresponds to the second digit.

What does the code on the air bag indicator mean?

If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light.

How does the air bag indicator light work?

If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. These codes are started by a single flash of the indicator light, followed by a two-second pause.

Why is my air bag light flashing code 34?

Code 34 is for DRIVER SIDE AIR BAG CIRCUIT LOW RESISTANCE OR SHORTED. The most common problem we have seen is the clock spring that connects the drivers side steering wheel air bag to the harness in the steering column. Replace the clock spring and the code 34 will be cleared. Below is a picture of the clock spring. Sounds likely to me.

Code 21 (double flash, pause, one flash) means the diagnostic monitor is not mounted properly.

What does it mean when your airbag light is blinking?

There are several reasons. It could mean that your battery backup is drained, that you have a worn-out airbag clock spring, or that your SRS airbag control module is faulty. It can also mean that something is wrong with your seat belts or impact sensors.

If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. These codes are started by a single flash of the indicator light, followed by a two-second pause.

How does the airbag warning light work on a Ford?

by Alexander Poirier. When there is a problem with a Ford’s airbag, the airbag warning light will illuminate and flash a code that identifies the problem. Because airbag problems range from a lost battery feed to a shorted circuit, it is important to understand the codes so that the airbag can be properly repaired.

What does a flashing air bag light mean?

The flashing means that there is a fault with the system. You can read the number of flashes and it will give you a code (codes listed below for ford ranger and Mazda B3000). If your code is not listed, just google the year, make and model of your car along with “airbag light code” (ex. 2001 Mazda B3000 airbag light code).

What does code 22 mean on Ford airbag?

Code 22 (double flash, pause, two flashes) means the safing center output circuit has shorted to battery voltage, Code 23 (double flash, pause, three flashes) means the memory clear circuit is improperly grounded and Code 24 (double flash, pause, four flashes) means there is a system disarm failure or internal diagnostic monitor fault.

Where is the trouble code button on a car?

This button is usually on the dashboard on the passenger side, and you may see it if you open the passenger door or the glove box. Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting.

Do you clear trouble codes before resetting airbag light?

Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. You should never just reset the airbag light without repairing the problem.

What causes the airbag to deploy in the passenger seat?

The passenger seat has an occupancy sensor that, when malfunctioning, can lead to the rapid deployment of the airbag. Fixing the sensor will solve this problem. The other problem could be with the clocking system. The system controls the car horn and steering wheel deployment.

Do you need scanner to read airbag trouble codes?

Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting. Do never clear the trouble codes before you fix the problem caused by the airbag light.

What is the Flash code on a Ford air bag?

Lamp flash code: 13 1.3 DTC B1317: Battery voltage high. Lamp flash code: continuous 1.4 DTC B1318: Battery voltage low. Lamp flash code: continuous 1.5 DTC B1342: Air bag control module is defective. Lamp flash code: 12 1.6 DTC B1869: Air bag warning indicator open circuit or short to ground.

How to repair Ford Ranger airbag code 12?

#12 Airbag Code Repair order (“Recheck SRS at each replacement.”) Visually check the wiring harness connection. Replace the harness if it has visible damage. Replace side air bag module (LH). (Before disposal, it must be deployed.) Replace the diagnosis sensor unit. How to disable Ford Ranger airbag module ?

What’s the air bag code on a Ford Falcon?

Follow the diagnostic procedures to service the fault condition flashing on the air bag indicator prior to code clearing. Cycle the ignition switch to OFF and then to RUN. Observe air bag indicator prove-out (six ? two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.

Where is the trouble code on an air bag?

Observe air bag indicator prove-out (six ? two seconds) followed by diagnostic trouble code (52-85) flashing completely one time. Locate the Diagnostic “Trouble Code Clear” Connector (grey connector). located underneath the glove compartment, left side (06010) containing Circuits 631 (T/R) and 57 (BK).

How to short circuit Ford Explorer air bag code 34?

Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).

What is code 21 on Ford airbag controller?

Each code is two digits and is counted by quick flashes and pauses. So a flash, flash, pause, flash equates to a code 21 on the fault code chart. The system will clear itself once the fault is corrected. Ford vehicles made after 2005 require a scan tool to read the codes, configure the controller and/or clear the light.

How to read and clear Dodge airbag codes?

Dodge airbag codes can only be read and system cleared with an airbag specific scan tool such as Maxdiag, Autel, OTC. Chrysler vehicles with Occupant Classification System (OCS) codes require vehicle specific equipment and procedures to reset

What does the code 19 on the air bag mean?

Posts: 1. First, the code 19 provided by the Air Bag Dash light only provides a signal that the Air Bag system has a fault. Consider the signal 19 to . +be a “family” fault indicator.

Where can I find the fault code on my air bag?

First, the code 19 provided by the Air Bag Dash light only provides a signal that the Air Bag system has a fault. Consider the signal 19 to . +be a “family” fault indicator. To find the fault you must use a reader to see the codes for to control wiring.

What to do if your airbag light has gone away?

Reset the airbag light and make sure that it disappeared from the dashboard. If it is still there – reread the codes and check for any trouble codes. Restart your car & test-drive. If the airbag light seems to have gone away from your dashboard – restart your ignition and go for a test drive.

How do you read the airbag codes on a Ford?

Ford vehicles made after 2005 require a scan tool to read the codes, configure the controller and/or clear the light. Use a scan tool like Maxdiag, Autel, OTC, Launch Airbag codes can be read using a jumper wire. Count the flashes on the airbag dash light. Each code is two digits and is counted by quick flashes and pauses.

What does the code 32 on the airbag light mean?

Code 32 (triple flash, pause, two flashes) means the driver side airbag has a circuit open or with high resistance, Code 33 (triple flash, pause, two flashes) means the passenger side airbag has a circuit open or with high resistance, Code 34 (triple flash, pause, four flashes) means the driver side airbag has a shorted circuit or one with low

Why does my airbag warning light keep coming on?

There are many different reasons that can cause your airbag light to flash or stay on. Just like troubleshooting your check engine light (get more details on how to reset check engine light here ), fixing your airbag warning light can be challenging sometimes and should never be ignored.

Where is the button to turn off the airbag light?

This is the first thing you should check when you want to remove the airbag light. Maybe someone before you turned it to Off by mistake, which will make the airbag light stay on in most cars. This button is usually on the dashboard on the passenger side, and you may see it if you open the passenger door or the glove box.

How long does the airbag light stay on?

To start the process get your watch ready and turn the ignition switch from “Off” to “On.” Once the airbag light comes on it will stay on for a total of seven seconds. Once it turns off, you will have a second to turn the ignition back to “Off.” After you have the ignition off for three seconds, you will need to turn the key back “On.”

How do you turn off the airbag light?

The first step is to turn the ignition switch on, which will make the airbag light to come on. The light will flash for exactly seven seconds. Once it is off, you have to turn off the ignition within a second. Turn the ignition on again after three seconds.

What does it mean when airbag warning light is on?

If the airbag light is on, it means that the airbag will not be able to deploy in the event of an accident. This is a dangerous proposition, and it means that you should avoid driving if at all possible in that vehicle. Interested in Leasing?

What happens if you reset the airbag light?

You should never just reset the airbag light without repairing the problem. This can deploy the airbags or non-functioning if an accident occurs. Let a professional replace the airbag’s parts if you are not sure of how to do it. Remember always to remove the battery connection when working with airbags.

What does the side air bag off light mean?

Your car is equipped with a passenger side air bag to protect against possible injury during an accident. However, if you notice the Side Air Bag Off light on in the dash, it might mean there’s something wrong with the system.

When did the Mercury Sable go out of production?

Mercury Sable. Due to low sales, the Mercury Sable ended production during the 2009 model year, with the final vehicle produced on May 21, 2009. Although the Ford Taurus remains in production (as of the 2018 model year), the closure of the Mercury brand left the full-size Sable without a direct successor.

What is the code for the airbag light?