Do you need to replace a trunk lock?
Do you need to replace a trunk lock?
You need not purchase an entire lock assembly; you only need a new cylinder that has been machined to match your master car key. A locksmith can read the reference numbers on your old cylinder and find a new one for this purpose. You can replace a trunk key lock in an afternoon if your locksmith has a replacement cylinder in stock.
How do you change the key on a car trunk?
Place the bit into the key slot of the lock and drill through the entire cylinder. Push up and own on the trunk lid until the lock releases and opens the trunk. Remove any interior body panels that prevent access to the trunk key lock. Use a flat-head screwdriver to pry out any clips or push snaps that hold the body panels in place.
How do you remove a trunk lock cylinder?
Tip: If you have the bolt-secured type of lock cylinder, you may need to use a socket wrench to loosen, and later tighten, this bolt. If you have the type of lock cylinder that is secured by a retaining clip, you will need to use gloves and needle nose pliers. Step 4: Remove the trunk lock cylinder.
Where is the pin on the trunk lock?
Pull the trunk lock out of the car when all the screws are removed. Release the cylinder pin. On the side of the key lock cylinder (the round tube in the center of your lock that the key turns to activate the lock) there will be a small circular pin that is flush to the surface of the cylinder body.
What’s the best way to replace a trunk lock?
If there is an electrical connector, squeeze the tab on its side and firmly pull straight away from the actuator to remove it. Tip: If you are unable to reach the cable with your fingers due to the design of your specific trunk lock actuator, use needlenose pliers or a flathead screwdriver to free the ball end of the cable from its seat.
How do you change the trunk lock actuator?
The steps below will outline how to change the trunk lock actuator on your vehicle in the event that it fails. Step 1: Access the trunk and locate the trunk lock actuator. Chances are if you need to replace this part, then one or more of the normal methods of popping the trunk are not functioning.
Where can I find the trunk lock cylinder?
Use the trunk release lever normally found on the floorboard of the driver’s side of the vehicle to pop open the trunk door. Using a trim removal tool, pop out each plastic retaining rivet to free the trunk liner. With the liner removed, you will have access to the back of the trunk door, and should be able to locate the trunk lock cylinder.
What should I do if my key does not open the trunk?
If the key and the manual release on the driver’s side floorboard both fail to open the trunk, and your vehicle was produced prior to 2002, you are going to have to use a flashlight and perform the next step from inside the trunk or cargo area. You will need to fold down the back seats and physically access the area.
Use the trunk release lever normally found on the floorboard of the driver’s side of the vehicle to pop open the trunk door. Using a trim removal tool, pop out each plastic retaining rivet to free the trunk liner. With the liner removed, you will have access to the back of the trunk door, and should be able to locate the trunk lock cylinder.
How do you remove a trunk key lock?
Remove any interior body panels that prevent access to the trunk key lock. Use a flat-head screwdriver to pry out any clips or push snaps that hold the body panels in place.
What happens when you replace a trunk lock cylinder?
Average rating from 130,525 customers who received a Trunk Lock Cylinder Replacement. The trunk lock cylinder on your vehicle is responsible for triggering the latch mechanism that opens the trunk when you turn the key. A faulty lock cylinder can be a security issue for you and your car.
How do you replace a retaining bolt on a trunk lock?
Replacing the retaining bolt is pretty straightforward; just hand tighten the bolt. If you have a retaining clip, you will likely need gloves and needle nose pliers to line it up and press it into position without cutting yourself or hurting a knuckle.
How do you remove a trunk liner from a car?
Step 1: Pop the trunk and remove the trunk liner. Use the trunk release lever normally found on the floorboard of the driver’s side of the vehicle to pop open the trunk door. Using a trim removal tool, pop out each plastic retaining rivet to free the trunk liner.
How do you remove a lock cylinder from a car?
The lock cylinder usually comes out by gently pushing it out from the inside. You may need to rotate the cylinder as you are removing it to clear the mounting hole. Step 1: Install the new lock cylinder. Feed the new lock cylinder into the hole in the trunk door, rotating as necessary to get it to seat properly.
How does a trunk lock work in a car?
Today’s trunk locking mechanisms are comprised of a keyed lock cylinder and a trunk lock actuator in cars that offer a power trunk release once activated. The trunk lock actuator then releases the trunk latch so the trunk can be opened.
