What kind of bolts do you need to remove a driveshaft?

Remove Driveshaft Bolts Remove the shaft differential flange mounting bolts. These bolts will be very tight so use good quality tools to avoid stripping. Some bolts can head 12 point heads as in this example which used a 13mm 12 point socket to remove.

Can a 12 point head be removed from a driveshaft?

These bolts will be very tight so use good quality tools to avoid stripping. Some bolts can head 12 point heads as in this example which used a 13mm 12 point socket to remove. These bolts also use lock tight to avoid coming loose while in operation and can be reapplied when reinstalling. 3. Remove Driveshaft Flange

What happens when a driveshaft is removed from a car?

Something you should know that may not be thought of is when a driveshaft is removed the car will no longer be in park. The car will roll because the link between the drive wheels and transmission is removed. You will need to raise the car or truck up using a floor jack and jackstays. Wear protective eyewear and gloves before you begin. 1.

What should I look for when replacing a driveshaft?

At this point the U joint at either end of the shaft should be checked. Grasp the yoke and move it in all directions. It should be a smooth motion with no rough spots or play in any direction. If play or rough spots occur then the U joint needs to be replaced. 6. Reinstall Driveshaft

Are there any problems with an automotive driveshaft?

Driveshaft themselves have very little problems with the exception of becoming bent if they come in contact with an obstruction. On the other hand the U joints can cause problems which are a part of the driveshaft such as chirping and clucking when the car is moving or put into gear.

What’s the difference between front and rear driveshafts?

A front driveshaft yoke is used to connect to the transmission while a rear driveshaft flange is used to connect to the differential. On older models the rear U joint bolts directly to the differential without using a rear flange. On front wheel drive cars there are two drive shafts which are called CV axles. What Goes Wrong?

What should I do if my drive shaft is leaking?

Using both hands gently slide the driveshaft from the transmission or transfer case. A small amount of fluid might leak out so have a fluid catch basin ready. This would be a good time to replace leaking transmission tail housing seal, universal joints or if removing the transmission or differential repairs are needed. 5. Check U joints

When to remove the front drive shaft on a Chevy truck?

Removing the front drive shaft on your Chevy truck may be necessary if you need to repair the U-joints or if it is blocking access to another component that you may be working on. The drive shaft connects to the transfer case at one end and the front pinion yoke on the other.

What to do if your driveshaft is failing?

If you suspect your driveshaft is having an issue, have the vehicle inspected by a professional technician to determine whether the driveshaft should be replaced. The most popular service booked by readers of this article is Vehicle Drivetrain Inspection.

Why does my car roll when I remove the driveshaft?

The car will roll because the link between the drive wheels and transmission is removed. You will need to raise the car or truck up using a floor jack and jackstays. Wear protective eyewear and gloves before you begin. 1. Mark the Driveshaft Mark the driveshaft orientation before beginning.

How much does it cost to remove a driveshaft from a car?

The cost of removing a driveshaft is incorporated in the cost of the additional repair being performed. If you were to take you car into the have the driveshaft removed as a standalone labor repair it would cost between $55.00 and $75.00 (US).

What’s the best way to disassemble an axle?

Use the correct-size deep-well socket or a shallow socket with an extension to reach in and loosen the four lock nuts nuts (a deep-well socket avoids the socket falling off the extension and having to fish the socket out from behind the axle flange). Notice that the brake hardware is in place.

What happens when you remove the nuts from an axle?

The rectangular shaped steel plate under the nuts holds the axle shafts and bearings in the housing. Once the nuts have been removed, you can lightly pull the plate loose. It is still trapped on the axle shaft, but you need to make sure it is loose.

Do you remove brakes before removing axles?

Keep in mind that removing the brake hardware prior to the axle shafts makes the job a little easier. Your overall plan is also a factor. If you have fresh brakes and are going to retain the drum style, then it makes sense to leave the brakes attached to the backing plates.

Where is the access hole on a 9 inch axle?

The access hole is in the wheel-mounting flange portion of the axle shaft and between two of the lug studs. Here you can see one of the nuts that retains the axle shaft. Four of these fasteners need to be removed so the axle shaft can be removed. This Tech Tip is From the Full Book, FORD DIFFERENTIALS: HOW TO REBUILD THE 8.8 AND 9 INCH.

How can I replace the drive yoke on my Honda Accord?

Grasp the yoke and move it in all directions. It should be a smooth motion with no rough spots or play in any direction. If play or rough spots occur then the U joint needs to be replaced. 6. Reinstall Driveshaft Before re-installing the driveshaft apply a small amount of grease to the yoke.

What kind of bolts do you need to remove a driveshaft?