How do you remove a nut from a CV axle?
How do you remove a nut from a CV axle?
Remove the cotter pin from the axle nut. If your vehicle has a cotter pin securing the axle nut, you will need to remove it. The pin will resemble a bobby pin with the ends folded back to hold it in place. You will need to use pliers to straighten the two bent ends of the cotter pin before you can remove it.
How big of socket do I need for CV axle?
Unfortunately, axle nuts do not have a standard size, and the socket size required will be different for different vehicles. The parts department at a certified dealership for your vehicle make should be able to tell you the exact size if you want to check before starting the project. Jack up the appropriate side of the car.
What kind of socket do I need for a VW axle nut?
Will work on any 30mm 12 point nut. VW axle nut socket. Whenever your axles need to be removed for front end work, like wheel bearings, nuts or CV boots, you will need a socket. It is a 1/2″ drive, 30mm, 12 point socket.
When to replace the seal on a CV axle?
Now would be a good time to replace the seal if its shot. I didn’t (stealership is 1hr away) but it didn’t leak afterwards, just be sure not to jack it up with the end of the cv axle. One side of the axle, the seal is huge. like i had to use 3″pvc pipe+coupling huge. the other side i used some sockets i had at work.
What do I need to replace front CV axles?
In this repair we use new axle or axles from 1AAuto.com, jack and jack stands, 15 to 22mm sockets with a ratchet extension. You’ll need a breaker bar and a pipe for some extra leverage, a 36mm socket, and I separate that one out because it’s not one that’s usually in your regular socket set.
What should I use to remove axle nut?
Wasn’t a problem getting the axle nut off with a 18″ breaker bar, but the bearing had practically welded itself on there.
What do you need to replace front axle bearing?
You will need the proper size socket to remove the axle nut and a torque wrench of proper capacity to tighten it. What were the symptoms that made you think the bearing was bad?
What to do if your CX axle shaft is stuck?
CX AXLE SHAFT STUCK – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
What’s the best way to change an axle?
By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.
How do you remove a front wheel drive transmission?
Pound the lower ball joints out of the lower control arm with the hammer. Keep the nut on the very end of the threads to protect the threads from damage by the hammer. Remove the outer tie rod end from the steering knuckle by removing the cotter pin, loosening the nut and pounding the tie rod end out.
What to do if your CV axle is not catching?
Jack up your vehicle and put on the parking brake. Rotate your front tires forwards or backwards and if you hearing grinding and/or clicking, and the CV joint is not catching, most likely the one that needs replacement will be there.
Remove the cotter pin from the axle nut. If your vehicle has a cotter pin securing the axle nut, you will need to remove it. The pin will resemble a bobby pin with the ends folded back to hold it in place. You will need to use pliers to straighten the two bent ends of the cotter pin before you can remove it.
By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.
Pound the lower ball joints out of the lower control arm with the hammer. Keep the nut on the very end of the threads to protect the threads from damage by the hammer. Remove the outer tie rod end from the steering knuckle by removing the cotter pin, loosening the nut and pounding the tie rod end out.
Jack up your vehicle and put on the parking brake. Rotate your front tires forwards or backwards and if you hearing grinding and/or clicking, and the CV joint is not catching, most likely the one that needs replacement will be there.
Can you remove axle nut before jacking up car?
Remove the axle nut. Once the cotter pin is out, you can remove the axle nut. The nut will take significant torque to remove, which is why it is much safer to remove the nut before jacking up the vehicle. Unfortunately, axle nuts do not have a standard size, and the socket size required will be different for different vehicles.
Remove the axle nut. Once the cotter pin is out, you can remove the axle nut. The nut will take significant torque to remove, which is why it is much safer to remove the nut before jacking up the vehicle. Unfortunately, axle nuts do not have a standard size, and the socket size required will be different for different vehicles.
How are the wheels connected to the transaxle?
Your CV joint has failed. The wheels of your front-drive vehicle are connected to the transaxle via axles that have constant-velocity-type universal joints at each end. There is an inner and outer joint on the left and right axles.
What can I use to replace front drive axle?
A large crescent wrench or pipe wrench is not an acceptable substitute. Borrow, rent or buy the right socket and a flex handle with at least an 18-in. handle, because that nut may be torqued to as much as 300 lb.-ft. You can use an air wrench to loosen it if you have compressed air available.
