How much horsepower does a 3800 Series 2 have?

How much horsepower does a 3800 Series 2 have?

Power is up to 240 hp (180 kW) and 280 lb·ft (380 N·m) of torque. Final drive ratios are reduced in most applications, for better fuel economy and more use of the engine’s torque in the low range. The engine was built in Flint, Michigan.

Are all 3800 Series 2 engines the same?

1 Answer. They are both series II’s, the engines are the same. GM updated the EFI on most vehicles between ’99-’00.

What is a 3800 Series 3 engine?

The 3800 Series III engine, found in the Grand Prix, offered 200 horsepower for the sporty sedan base model. The supercharged 3800 Series III, found in the Grand Prix GT or GTP (depending on model year), unleashed 260 horsepower.

What engine replaced the 3800?

That adds up to a lot of cars. But it pales in comparison to the number of vehicles that automakers sell in the U.S., an average of more than 15 million a year since 2000, according to Edmunds data. GM built and installed more than 25 million of the 3800 model V6 engines in its vehicles between 1975 and 2008.

What year did the 3.8 Series 3 come out?

Introduced in 2004, the Series III Supercharged engine has 20 more hp than the previous generation 3800, which is due to the improved Gen V Eaton M90 Supercharger compared to the series II’s Gen III Supercharger.

What’s the difference between a 3800 Series 2 and Series 3?

The biggest difference between the motors is the Series III has stronger connecting rods, an aluminum upper plenum, which eliminated the leak point of the Series II, and it had a return-less fuel system setup.

Is the GM 3.8 a good engine?

The 3.8 is a great engine but it is not quite smooth enough for where Buick is going as the leader in NVH. The HFV6 is also a great engine.

What is the difference between the 3800 Series 2 and 3?

How much HP does a 3.8 v6 have?

An Awakening… In box stock form, the 3.8L Essex V-6 produces 145-150 hp at the crankshaft. According to Super Six Motorsports, that’s 0.625 hp per cubic inch or 38.2 hp per liter.

What vehicles have a GM 3800 engine?

The GM 3800, 3.8-liter V-6 came in the Chevrolet Monte Carlo, Malibu, El Camino, Impala, Monza, Caprice, Camaro and Lumina. Chevrolet replaced the Buick version with another 3.8-liter V-6 version, based on the Chevrolet 305 V-8, from 1980 to 1985. But the Buick V-6 returned to power post-1985 Chevys as the GM 3800.

What year did GM start using the 3800 Series II?

The GM 3800 Series II engine, introduced in 1995, is quite a different engine from its predecessor, the Series I engine. While the stroke for the 3.8L engine remained at 3.4″ (86 mm), and the bore remained at 3.8″ (97 mm), the engine architecture changed dramatically.

What is a 3800 motor?

The Buick V6, popularly referred to as the 3800, originally 198 cu in (3.2 L) and initially marketed as Fireball at its introduction in 1962, was a large V6 engine used by General Motors. The block is made of cast iron and all use two-valve-per-cylinder iron heads, actuated by pushrods.

What is 3800 V6?

Though the pre-3800 rear-wheel drive (RWD) V6 uses the Buick, Oldsmobile , Pontiac (BOP) bellhousing pattern, an oddity of both the front-wheel drive (FWD) and RWD 3800 V6 is that although it is a 90° V6, it uses the GM 60° V6 bell housing (Metric Pattern).