What does Ford axle code l9 mean?
What does Ford axle code l9 mean?
If Your 2014 Ford F-150 has a code l9 that means that Your rear axle’s gear ratio iS3. 55 and that it has an electronic locker. The use of a locker is better for off road and low traction situations.
What does axle code H9 mean?
The Ford F150 axle code H9 means that the vehicle has a 3.55 ratio and Limited slip differential.
How do I identify a Ford 9 rear end?
Many enthusiasts will tell you to look for the two dimples in the rear cover to determine if the unit is a 9-inch, but this is not always true. Ford also had an 8-inch third-member rear end that had a dimpled cover. The best test of a 9-inch carrier is to try removing the two lower carrier case bolts.
What Ford axle do I have?
There’s no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you’ll see a sticker like the one shown below: You’ll see that the area labeled (F) is for the Axle Code.
What is l9 gear ratio?
L9: 3.55 ratio, electronic locking differential. L6: 3.73 ratio, electronic locking differential.
What is a 3.55 axle ratio?
Automakers build trucks with a range of optional axle ratios. Technically, the number should be expressed as a ratio, such as 3.55:1, meaning the drive shaft turns 3.55 times for each turn of a wheel. But that gear ratio would most commonly be referred to as “3.55” or simply “three fifty-five.”
What is a 3.55 gear ratio?
Understanding Axle Ratios Technically, the number should be expressed as a ratio, such as 3.55:1, meaning the drive shaft turns 3.55 times for each turn of a wheel. But that gear ratio would most commonly be referred to as “3.55” or simply “three fifty-five.”
What is special about a Ford 9 inch rear end?
Ford 9-inch rearends have a third “extra” pinion support bearing located at the rear of the drive pinion. Other rearends have only the usual center two support bearings.
How do I know what axle I have?
Stamped Number on the Axle To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.
How do I identify a Ford 8.8 axle?
You can identify the Ford 8.8-inch rear by its rear cover. It has a thin metal or plastic 10-bolt cover, and the bolts are 7/16-inch thread. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The 8.8-inch pinion shaft is 15/8 inches and has 30 splines.
Where do you find the Axle code on a Ford truck?
Identify Your Ford Truck Axle From The Door Sticker. There’s no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you’ll see a sticker like the one shown below: You’ll see that the area labeled (F) is for the Axle Code.
What does the number 4l11 mean on a Ford axle?
The code, 4L11, tells us that it is a 4.11:1 ratio with a limited-slip or Traction-Lok differential. It also has a 9-inch ring gear. The axle tag typically has two lines of numbers and letters stamped on it.
What is the Axle code for a 2004 Ford Excursion?
2004 Ford Super Duty Axle Codes: 31 — 3.73 non-limited slip, F-250/Excursion 32 — 4.10 non-limited slip, F-250 41 — 3.73 non-limited slip, F-350
How to tell the axle ratio of a Ford truck?
Identify Your Ford Truck Axle From The Door Sticker Axle Code (Door Sticker) Axle Gear Ratio 01 Ford 9″ 2.75 02 Ford 9″ 3.00 04 Ford 9″ 3.25 07 Ford 9″ 2.47
