What to do with a GMC Blazer S10?

1. Disconnect the negative battery cable and properly relieve the fuel system pres- sure. 2. Drain the engine cooling system and the engine oil into separate drain pans. 3. Remove or disconnect the following: •Hood •Oxygen Sensor (O2S) electrical connection •Exhaust pipe from the manifold 26770_U07.qxd 8/30/05 3:01 PM Page 13

What kind of wiring does a Chevy Blazer have?

WIRING INFORMATION: 1989 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

Where is the hoist on a S10 engine?

Attach the engine hoist to the engine, using the chain and placing one bolt in the driver’s side front of the cylinder head just below the valve cover. Place the back bolt on the rear opposite side of the motor again just under the backside of the valve cover. Lift out the motor.

What causes a noise when you brake on a Chevy?

Brake Chatter: Warped or improperly finished rotors will cause this noise. Brakes that Grab: If there is oil, brake fluid or grease on the pads, they will slip and then grab hold. You may feel your Chevy jerk when you brake. Check your pads for any type of contamination.

Where can I get a S-10 manual brake swap kit?

KIT with: KIT with: KIT with: FREE SHIPPING TO THE LOWER 48 STATES. Matching Rubber Firewall Gasket – Keeps the cars interior sealed from the engine bay. Stainless Steel Mounting Hardware – NO rusty bolts or nuts Adjustable Push Rod Assembly – Engineered to work with and function in the 2nd Generation (1994-1997) S-10 Trucks and SUVs.

What kind of disc brakes can you use on a S-10?

For use with G-Body, S-10, and 3rd/4th Generation F-Body vehicles. Can be used with converted rear disc brakes depending on rear caliper piston size. These master cylinders are chosen to be used with the MANUALBRAKES.COM adapter plates and push rod assemblies. 24mm Bore Master Cylinder. Actual bore size is 24mm (0.945″)

What kind of rear caliper do I need for S-10?

*Any Rear Drum *Stock Size Rear Caliper *Metric Rear Caliper or LESS or MORE FREE SHIPPING TO THE LOWER 48 STATES. Matching Rubber Firewall Gasket – Keeps the cars interior sealed from the engine bay. Stainless Steel Mounting Hardware – NO rusty bolts or nuts

When did the Chevy Blazer come out in the US?

Every Manual available online – found by our community and shared for FREE. Enjoy! The Chevrolet Blazer was a mid size SUV from General Motors between 1983 and 20 0 5. It was based on Chevrolet S-10 and technically the twin of GMC Jimmy.

How big is a bolt on a Chevy Blazer?

Torque the left bolt to 22 ft. lbs. (30 Nm) and the right bolt to 32 ft. lbs. (43 Nm). •Wires. Torque the battery feed wire nut to 71 inch lbs. (8 Nm). •Alternator brace. Torque the nuts and bolts to 22 ft. lbs. (30 Nm). •Accessory belt •Negative battery cable 4.3L Engine Install or connect the following:

Is the S-10 Blazer powered by a V8?

The above V8 powered S-10 Blazer was real fast. The V8 conversion did not cause the accident, the driver did. Wrecking yards are full of examples of recklessly driven vehicles. Keep that in mind before you even think about showing off the performance of a V8 S-Truck.

Is there a Repair Manual for a Chevy Blazer?

You Fix Cars has auto service repair manuals for your Chevrolet Blazer – download your manual now! Chevrolet Blazer service repair manuals

What kind of gas mileage does a blazer get?

With 235/75-15 tires and 3.73 gears, this Blazer gets about 22 mpg on level freeway trips at 65 mph. Normal overall fuel mileage is about 15-19 mpg. 0-60 mph takes ten seconds at sea level. This truck now weighs about 3900 lbs and has every factory option.

Why are the Spider injectors leaking in the L35 engine?

The spider system uses a central pump with 6 tubes connected to it that lead to each of the 4.3L vortec cylinders. In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault.

What to do with a GMC Blazer S10?