How do you replace an intermediate steering shaft?

Replace the upper intermediate shaft. Install the upper intermediate steering shaft through the dash boot seal and slide the lower end into the steering gear coupling shaft. Raise the upper end of the intermediate steering shaft and install into the steering column shaft.

How to fix a steering shaft on a GM car?

Install the upper intermediate steering shaft through the dash boot seal and slide the lower end into the steering gear coupling shaft. Raise the upper end of the intermediate steering shaft and install into the steering column shaft. Install the upper bolt and nut.

Is the I-shaft p / n 19155614 a dampened shaft?

• I-shaft P/N 19155614 has been designed to replace previous designed dampened and non-dampened I-shafts. The physical difference in the yoke size will accommodate all vehicles listed in this bulletin. ”

How to fix steering shaft on General Motors?

How does an intermediate shaft help your vehicle?

What is an Intermediate Shaft and How Does It Help Your Vehicle. The intermediate steering shaft, is what helps to connect the steering wheel with the steering gearbox or rack and pinion in many lightweight cars. The motor intermediate shaft is the torque steer replacement.

When did the Dorman steering shaft come out?

If you’re buying this, you’re probably replacing the originally made in 2000-20006 steering shaft that has proven to cause clunking after awhile, which means that shaft was installed by the factory. The other thing of note, is that this one was visibly thicker at the attachment point than the original, which explains why it didn’t fit.

Turn the steering wheel to expose the bolt on the upper part of the shaft under the dash and use the seatbelt to hold the wheel in position 5. Loosen the upper bolt and re3move it and the nut to free the upper shaft 6. Remove the three 10mm nuts holding the rubber shaft housing that’s mounted on the firewall 7.

How does the steering shaft connect to the gear box?

One of those parts is the intermediate steering shaft. It connects the steering wheel with your steering gear box or the rack and pinion in your vehicle. The intermediate steering shaft has what’s called a universal joint on one end which is what allows the shaft to connect to the gear box.

When to replace the lower steering column bearing?

PSA: If you’re replacing the intermediate steering shaft on your GM product….. Not open for further replies. Don’t be an idiot like me and neglect to replace the lower steering column bearing that’s sitting right there.

Why does my steering shaft have a problem?

The shaft problem is because the shaft is a two-piece design, which has an inner shaft and outer shaft. Over time, the inner part of the steering shaft, which slides on a plastic piece inside the outer sleeve of the steering shaft, begins to develop a bit of slop from wear, at least that’s the supposition being made.

Where is the J 42640 in the steering column?

Set the steering wheel in the LOCK position on 2001 and prior model year vehicles. For 2002 and later vehicles, install the J 42640 in the steering column lower access hole. From under the hood, remove the lower bolt that connects the upper intermediate shaft to the steering gear coupling shaft.

How do you fix a steering column shaft?

Raise the upper end of the intermediate steering shaft and install into the steering column shaft. Install the upper bolt and nut. Tighten the bolt to 47 N·m (35 lb ft). Install the lower bolt and nut. Tighten the bolt to 50 N·m (37 lb ft). For vehicles equipped with adjustable foot pedals, perform the following steps: 14.1.

When do you remove the steering column lock?

Notice: On the 2002 and later model year vehicles, the steering column LOCK was removed from the steering column. It is critical that the J 42640 – Steering column Anti-Rotation Pin is used when servicing steering columns on 2002 and later model year vehicles.

How do you install a steering column nut?

What happens when the seal on an intermediate steering shaft breaks?

A broken seal is often the culprit when it comes to a problem with your intermediate steering shaft. This seal is what holds the needle bearings that we mentioned earlier. Where the seal breaks, the needle bearings become exposed and they can lose their lubrication.

What happens if you have a bad steering shaft?

However, if there is a bad intermediate steering shaft or column, then you won’t be able to lock the steering wheel at the angle you’ve chosen. When you turn the steering wheel in a vehicle with power steering, the wheel will usually go back to the center afterward. This is considered to be a safety feature in every power steering system.

How much does it cost to replace a power steering shaft?

This is considered to be a safety feature in every power steering system. However, if the wheel fails to return to the center after you take your hands off it, then there could be a problem with the intermediate steering shaft or the steering column. The cost to replace a bad intermediate steering shaft is would be anywhere between $200 and $350.

How do you replace an intermediate steering shaft?