Why does my Chevy Truck start and idle?

Not sure why this test caused a better and longer gas flow than the above test of just putting the ignition in the ON position and seeing how much gas comes out of the line before the fuel filter. Last test says to start the vehicle and remove the relay.

How can I keep my car at idle?

Step 3 – Engine vacuum is a sealed system and must hold a specific amount to maintain proper idle conditions, inspect the engine vacuum hoses and intake gaskets. Step 4 – The air intake boot or tube is used to deliver air to the intake system of the engine.

How to troubleshoot an automotive engine high idle?

The troubleshooting procedure for high and low idle conditions are similar, which are included in the following: Step 1 – If the check engine or service engine light soon has illuminated retrieving the diagnostic trouble codes could lead you in the right direction of what the problem is, or is related too.

Why does my C / K 1500 stall at low idle?

This all started after spraying motor down after mudding instant idle issues wanted to stall and would at red lights and stops then it started surging redid the ignition timing fixed the surge now it’s just low idle with stutter and hard to start so really it could be a number of things …. if my ecm was bad wouldn’t the truck not run At all

Why does my car shut off when stepping on the gas pedal?

received a Car shuts off when stepping on gas pedal Inspection. Rough idling, frequent stalling, and inconsistent acceleration are all signs that something is amiss with your car. There are a number of systems that can cause this problem.

Can a faulty fuel pump cause a car to not start?

Faulty fuel pump: The fuel pump moves fuel from the gas tank to the engine. If the fuel pump is malfunctioning, the engine will be getting less fuel than necessary, which will lead to performance issues, and ultimately cause the vehicle not to start.

Why does my Dads 93 Chevy truck die?

My Dads 93 was doing what seems to be the same thing as yours. It ended up being the Fuel Pump Relay. If I press the gas pedal it dies. It’s been acting weird for a while now. For instance, when I take off from a dead stop at a light it sort of hesitates when I hit the gas.

Why does my Truck start when I press the gas pedal?

If it has gasoline in it, your regulator is bad. It’s about $50 for a new one at AutoZone. It’s a common problem on this engine. If this does turn out to be the problem, the reason it starts when you hold the key is because you are putting the ECM in “flood mode”.

What kind of car wont start unless you press the gas pedal?

I have a 2002 avalon XLS. In the morning the car cranks but wont start unless I press the gas pedal. After that everything was fine. But recently the problem is getting worse. The car became harder to start although it will start eventually. I have changed the Mass air flow sensor, but did not solve the problem. Any suggestion?

What’s the name of the truck that won’t start?

I recently bought a 2000 Silverado 1500 5.3 V8, Everything was fine up until the last couple of weeks. The truck wont start unless i press on the gas pedal as I turn the key, even then it still shuts off every once in a while while I’m idling whether at a stop light in drive, or in a parking lot in park.

What does it mean when your car won’t start unless you give it gas?

The Car Won’t Start Unless I Give it Gas: Diagnose the Issue! Nothing can be more annoying than a car not starting at the beginning of a day! However, if it does start on pumping the gas pedal, you may get a sigh of relief. But this doesn’t mean an end to the problem.

Why does my 1995 Chevy Silverado stall out?

Browse “SIMILAR TOPICS” At The Bottom Of This Page. On 95 chevy that’s still want stay crank and still stalls out. This is Amy from ms down south..just by chance have u check to see. About catalytic onverter could be stopped up, and/or donnut gaskets could have ur pips stopped up where u are getting little air out.

Is the Z71 k1500 a bad car?

Those are textbook symptoms of a bad one. My good friend has a ’98 3/4 ton with the 5.7 and his was doing the exact same thing, no check engine light, did a complete tune-up…all to no avail. He swapped the MAS with a friend of his who had a ’97 and it ran perfect.

What causes a Chevy Silverado to run rough?

If an oxygen sensor goes bad, it can make your Silverado run too lean (or rich). A super lean running engine will often idle rough. Fuel Injectors. The fuel injection systems job is to atomize the fuel into fine mist.

Why does my GMC Truck die at idle when warm?

So I wasn’t suspicious of fuel pressure, then later checked it and I have a steady 10psi from the moment I turn the key until a few seconds after it dies so the fuel pump is good. It runs strong and is fine until I idle. This happens only when the engine is warm and last time I checked it never went into closed loop.

Why is my Chevy Silverado running rough at idle?

Really, your Silverado will be running rougher at any RPM, but a misfire will be most pronounced at idle. Spark Plug Wires – While not every model and engine combination of vehicles today comes with spark plug wires (a lot are now coil on plug), if your Silverado happens to have them, they can go bad and cause a rough idle.

Why is my GMC Sierra 1500 stalling and dying?

There is no code given. Have changed the injectors, timing, fuel tank, fuel pump, fuel pump, map sensor, cooling temp sensor on front of block, rebuilt the tbi, air idea valve. None of this hasite helped. The truck starts and dies. Have to give a little gas to keep running. While driving have to 2 foot it so it won’t die.

What causes an Audi A4 to idle rough?

A super lean running engine will often idle rough. The fuel injection systems job is to atomize the fuel into fine mist. If a fuel injector has an issue with this process, it will either let too much or too little fuel into the combustion chamber relative to the amount of air.

Why are the spark plugs on my Chevy Silverado not working?

Spark Plugs – One of the absolute most common causes (if not the most common reason that your Silverado may be misfiring) is the spark plugs. Although most modern vehicles use iridium spark plugs, they still need to be changed at the manufacturers recommended interval.

What’s the idle RPM on my Chevy Suburban?

My 1997 Chevy Suburban (5.7) is acting up on me. When I start it up the RPM and idle seem fine. As I let it sit for a couple of seconds the RPM’s slowly begin to drop until they finally bottom out at about 1K. As soon as I put it into Reverse/Drive etc. the RPM’s drop below that mark and it struggles to stay running.

How does idle speed work on a GMC Truck?

Scan it for codes. The control module controls idle speed with an idle air control (IAC) valve. The desired RPM is based on sensor inputs and the actual engine RPM. Four circuits are used in order to control the IAC valve, allowing a precise amount of air into the intake manifold.

Can a Chevy Silverado 1500 start and run?

Although I tried to start it multiple times over a couple weeks I gave it one last try after I called the tow truck. It started right up and engine stayed running like it was supposed to. No more problems for almost a year until about a week ago. I did nothin to fix it a year ago.

Why does my Chevy truck sputter when I accelerate?

The engine starts and runs fine, when I leave for or from work. But when I accelerate out of the parking lot it hesitates and really sputters. If you try to accelerate more it backfires a few times and then takes off like there’s nothing wrong.

When do intake manifolds leak in a Chevy truck?

Last edited by EKinMN on Oct 20 2011, 11:39am, edited 1 time in total. Leaky intake manifolds aren’t uncommon with any make/model/year. It’s not a bad idea to double-check your previous work. Is it safe to assume that you cleared the codes after the repair?

Why does my Chevy truck backfire when I hit the gas?

Its sputtering, backfiring, misfiring, in the low RPM band (below 2k) hit the gas and it upshifts and clears up. I also noticed its idleing rough. So, leaky-cracked manifold?

What kind of gas does a 1997 Chevy truck use?

1997 chevy c1500 WT with 4.3 . getting harder to re crank.. Only driveable with both stop revving to keep it going. And that still doesnt work well. Work ive done. New cap and rotor. Cleaned…. Exh gas.

What kind of truck starts and then dies?

Forgot to mention this is a 1995 K1500 5.7 with TBI. When it first start if you give it some gas dose it stay runing?? My 2001 suburban did this it would start and die.

What kind of idle does a GMC Sierra have?

After the truck starts and is warm at a stable idle in park/neutral it’ll rev up fine. But the stable idle won’t last long, it’ll idle low and rough. Mpg has decreased drastically and give off a rich smell when running.

What kind of engine does a GMC pickup have?

This engine was designed as a direct replacement for 1987-1995 Chevy & GMC pickups, SUV’s, and van applications. These vehicles featured a 350 ci, 5.7 small block Chevy with TBI (throttle body injected) EFI system and swirl port heads.

How much horsepower does a 350 ci Chevy have?

These vehicles featured a 350 ci, 5.7 small block Chevy with TBI (throttle body injected) EFI system and swirl port heads. Producing up to 210 hp in factory spec, this engine can also be retrofitted into an older car with a performance carburetor to produce up to 250 hp.

Why does my GMC Sierra 1500 stall at high RPM?

At higher rpm seem almost like the exhaust is clogged but the cat has been bored, itll rev up but just wont really go. Today experienced a poping sound almost like a backfire from underneath. After the truck starts and is warm at a stable idle in park/neutral it’ll rev up fine.

Why does my 1993 Chevy TBI stall at idle?

Timing is steady and not jumping all over. It is a fuel issue. The only code that ever sets is a P044, lean exhaust, and the exhaust is really lean. We have swapped PCM/PROM with a same year Suburban, no change. Both vehicles run the same as this did using the other’s PCM.

What’s the idle time on a GMC TBI?

IAC 160 steps, throttle sensor . 43 volts, map sensor 2. 15 V, rpm 800,egr duty 0%, throttle angle 0%, injector pulse 4. 3ms, knock sensor 179, engine run time 2 seconds, Well it is not an exhaust restriction. I dropped the exhaust piple down and started her up. Still stalled out in about 2 seconds or less.

What’s the fuel Gage on a 1993 Chevy truck?

Fuel gage never wavered at 12-13 psi. MAP around 2.9v when PW 2.8MS when truck seemed to be falling a little flat under brake torque. This thing is really close to getting a carburetor on it.

Why does my Chevy truck stall at idle?

Filter is not that old, and if plugged or if pressure regulator is malfunctioning, why do I never see fuel pressure at throttle body so much as waver lower than 12psi? Also, many times the lean condition will start just off idle so bad so that truck wil fall flat on its face and stall.

Why does my Chevy truck shake at idle?

While the truck is idling with 02 lean, a quick shot of carb spray in the throttle body will cause the 02 to go rich. And when the truck sometimes starts shaking at idle it will smooth out with carb spray. I jst don’t understand why the computer is not trying to richen the mixture up based on the 02 saying lean.

What causes a GMC truck to turn over but not start?

If the engine starts up normally after doing that, it means that fuel pressure is bleeding off and the fuel pump needs to prime the lines before it can start. It can bleed off from one of two places. 1. Fuel pressure regulator has an internal leak, and fuel is bleeding off back to the tank though the return line. 2.

Fuel gage never wavered at 12-13 psi. MAP around 2.9v when PW 2.8MS when truck seemed to be falling a little flat under brake torque. This thing is really close to getting a carburetor on it.

Why is idle speed not coming back up?

If the ISC system is working correctly, the PCM should adjust idle speed to keep the engine from lugging down when the A/C compressor engages. If idle speed drops down and does not come back up, the ISC system is not responding the way it should.

What causes a car to run lean at idle?

If the root cause is an electrical problem within the idle air control valve itself, you will likely have to replace the IAC. A vacuum leak is a hole in a vehicle’s air intake system behind the mass air flow (MAF) sensor that allows unmetered air into the engine. This throws off the expected air fuel ratio and causes the vehicle to run lean.

What to do when engine stall Idle Stop?

Aim for the little air bypass holes in the throttle opening. Use the small plastic tube that attaches to the nozzle on the aerosol can to aim the cleaner directly into the bypass port (s). Let the cleaner soak for at least 10 minutes before giving it another blast of cleaner.

What should the fuel pressure be at idle?

Fuel pressure should be within specifications when the key is on, then drop 4 to 6 psi once the engine starts and is idling. Note: Some vehicle manufacturers list pressure specifications for both KOEO and idle, while others only list a fuel pressure specification for one or the other.

How does the idle speed of an engine work?

The engine’s idle speed is controlled by how much air is allowed to bypass the throttle via the idle bypass circuit in the throttle body. The PCM monitors idle speed and operates a solenoid or small electric motor to move a valve that regulates airflow through the air bypass circuit.

What causes engine to bog down when giving throttle?

Driving along at about 40-50mph and I go to accelerate and a get a shuttering/bogging down of the engine and have no real throttle. If I gently press down on the petal I can accelerate, but the moment I try and step on it I get the symptoms described above.

Can a bad throttle position sensor cause idle surging?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light

What causes idle surges on a car ECM?

Is the Chevy TBI 454 having Idle problems?

Recently rebuilt the 454 in my 1990 TBI Burb. I am having a terrible time with getting it to idle smooth. The engine has a little over 500 miles on it. I have spent countless hours going over the engine looking for vacuum leaks and believe every thing is OK on that front.

How to troubleshoot your TBI fuel injection system?

Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad. See

What is the TBI code on a 1990 Chevy truck?

Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.

Why is my GM Vortec engine bogging down?

If so look into a vacuume leak or possibly bad igntion components. If your not using delco plugs in this motor that can be a big contributor to your problem. GM vortec engines hate anything but vortec plugs and will do all kinds of weird things. And yes a clogged converter could cause this sort of thing to happen.

Why does my GMC Sierra 1500 stall while in gear?

Motor wants to stall while in gear (but doesn’t do it out of gear once over 1000 rpm it dosent) seem to stall and it is only from a dead stop. Fuel filter has been replaced and TBI was rebuilt last April but it sort of used to do something like this when it was like 40 degrees or below. Could be torque converter lockup solenoid in the trans.

What should I do if my Chevy truck dies?

Last test says to start the vehicle and remove the relay. The vehicle should continue to run (which it did not because it died in seconds). If the vehicle stalls check the fuel pump/oil pressure switch and its wiring. Book does not say where fuel pump/oil pressure switch is.

Why does my Chevy Silverado idle at 500 rpm?

Reasoning is emissions related and the truck will automatically run it (choak it) @ ~1K +/- cold until enough heat has been generated then drop it down. But as wisely suggested above, good fuel additives can be really helpful. I’ll add chevron’s techron to the list.

What causes large idle RPM drop from unloaded to in gear?

Idle drop would then be in the 100 RPM range with ‘in-gear’ idle setting coming out @600. A large drop from Unloaded to In-gear idle setting can otherwise usually be attributed to either a vacuum leak or a convertor that’s to ‘tight’ for the engine set-up

What’s the idle speed of a Chevy truck?

Thanks. Last edited by EKinMN on Nov 11 2011, 2:54am, edited 1 time in total. Most trucks start up at about 1000 RPM, and then drop down when it warms up. Although mine is a lot different than yours, I can tell you it will idle down to about 500 RPM when warm.

Why does my Chevy k1500 stall when gas is released?

I have been working on our 89 Chevy K1500 and am still having an idle issue. The truck idle drops and lopes and occasionally completely stalls. This usually happens when driving slow in town… backing out of parking space, letting off gas when coming to a stop sign or to park etc. It does fine to start and accelerate.

Why does my truck not start after sitting for a long time?

This can happen when the check valve in the fuel pump assembly leaks pressure back into the fuel tank. The longer the truck sits the harder it is to start. Try this, turn the key on for 2 seconds then off, do this two more times then try and start it.

Why does my Truck start cold in the winter?

IMO not glow plugs as it starts. It does sound like fuel gelling, summer fuel will gel at above freezing temps. One would have to find out what your fuel is rated for as it is blended throughout the winter months. Another possibility is the fuel filter, cold thick fuel may not pass as easily.

What to do if your truck won’t start?

To be able to get it to start the truck has to be primed with the key and then put the gas pedal to the floor while cranking. I have recently replaced the fuel filter, air filter, and fuel pressure regulator in attempt to fix this problem.

Why is my idle air control not working?

My Idle Air Control also responds accordingly by low counts when it runs good for 3 second and opens up when the engine is starting to stall and trying to keep it running . It dies anyway. I have new gasket on the base of the TBI assembly.

Why is my truck not running when I leave work?

Truck wouldn’t stay running when leaving work today. It starts then dies after a couple of seconds. Had it towed to a friends where we pulled out the Chilton book and began troubleshooting.

Why does my GMC TBI start cold running?

Haven’t pulled the plugs right after because of the difficulty to get to them. This is all cold running because it won’t run long enough to get the engine hot or in a closed loop. Some 4. 3 have a IAT and some not. This one doesn’t have a IAT.

When did the Chevrolet 305 V8 engine come out?

As America faced an energy crisis and the government began to regulate a car’s emissions, General Motors made adjustments to many of their small block, V8 engines. GM introduced the Chevrolet 305 engine in 1976 to provide a smooth driving performance while allowing for lower octane fuels and lower emissions.

What’s the idle RPM on a Silverado Silverado?

Re: high idle PLEASE HELP!!! When i pull the vac line from the booster the idle rpm stays at the 1200 I had been idling for 2 yrs. It only runs rougher but maintains 1200. When I pull the same line from the back side of the intake she revs really high. Enough to scare you so I plugged it back in really fast.

Is there an intake manifold leak at high idle?

You may have an intake manifold leak on the bottom side of the engine at the lifter galley (I base this assumption by the fact that when you spray eather into the valve cover it changes the engine speed.) Re: high idle PLEASE HELP!!! You probably have a leak like aste25 mentioned.

What causes a GMC Sierra 1500 to stall?

But the stable idle won’t last long, it’ll idle low and rough. Mpg has decreased drastically and give off a rich smell when running. 308 people found this helpful. Bad hesitation off of the start, pumping the gas pedal helps to get her going. Pushing the pedal hard well bog it out and almost stall. 290 people found this helpful.

How to time a Chevy 305 engine step by step?

How to Time a Chevy 305 Engine Step 1. Warm up then engine then turn it off. Step 2. Attach the timing light by clamping the spark plug lead over the number one spark plug wire. The number one wire… Step 3. Locate the timing mark plate on the timing cover. If it is hard to see the numbers,

What does the fuel smell like in a GMC Sierra 1500?

If so pull the air filter off and sniff the throttle body for a fuel smell. If the diaphragm has ruptured it will literally be like putting a hose with fuel into the intake and running it full.

What causes a truck to stall when gas is released?

The truck idle drops and lopes and occasionally completely stalls. This usually happens when driving slow in town… backing out of parking space, letting off gas when coming to a stop sign or to park etc. It does fine to start and accelerate. I have done a tune up including oil and filter, fuel filter, spark plugs, wires, cap and rotor.

What causes a car to stall while idling?

A common problem with air passages in the throttle, and the IAC valve itself, is carbon, dirt or fuel varnish buildup. If air can’t go through the air ports when needed, the engine may stall when you reach a stop or while the engine is idling. Locate the IAC around the throttle body. Unplug the IAC solenoid electrical connector.

What causes stalling on a 1990 Chevy k1500?

So far it has a new distributor (for an unrelated problem), idle valve, throttle position sensor, knock sensor, temperature sensor, fuel filter, plugs & wires. The idle valve and tpi both tested bad, and replacing them helped on general driveability but didn’t affect the stalling.

Forgot to mention this is a 1995 K1500 5.7 with TBI. When it first start if you give it some gas dose it stay runing?? My 2001 suburban did this it would start and die.

How old was my Chevy truck when it died?

Had it towed to a friends where we pulled out the Chilton book and began troubleshooting. First thing we replaced was the fuel filter. It was 9 years old and when we blew into it there was a lot of restriction. After that we ran through the tests under Fuel Pump.

What causes a Chevy 350 to backfire when idle?

If a main vacuum hose such as the power brake booster feed line has broken or failing off it will cause a lean backfire due to the additional air allowed into the engine intake manifold. This problem will be accompanied by high or low engine idle and a harder to push brake pedal than normal.

What was the problem with my 1995 Chevy Silverado?

My 1995 Chevrolet Silverado truck had a hesitation problem, which we were able to fix by replacing some parts. My Chevrolet truck would idle fine and passed the Emissions test, and there were no check engine lights, but there was hesitation when I stepped on the gas pedal. The engine would bog down or almost stalled out instead of going faster.

What kind of idle does a 1998 Chevy Blaz have?

Rough idle, surging, and hesitation – 1998 Chevrolet Blaz… Idles rough, worse under load and surges at times. Rpm varies at constant speeds (occasionally), hesitates when trying to pass a vehicle or speed up. doesn’t shift from 3rd gear to overdrive sometimes when hard accelerating, until I release the accelerator.

Why does my Chevy Blaz hesitate when going up a hill?

Rpm varies at constant speeds (occasionally), hesitates when trying to pass a vehicle or speed up. doesn’t shift from 3rd gear to overdrive sometimes when hard accelerating, until I release the accelerator. Cruise control works intermittently. Going up on an incline, losing lots of power. No DTC except for p0446 emissions circuit.

Can a truck go over 2, 000 rpm at idle?

The truck will not accelerate past 2,000 rpm, and will not go above 40mph. It runs fine at idle,but if you press down on Limited: accelerate..runs fine..neutral, it revs up to 3,000 rpm… The truck will not accelerate… The truck will not accelerate past 2,000 rpm, and will not go above 40mph.

What does it mean when your car dies at idle?

When a car dies at idle, it can be both frustrating and embarrassing for the driver. It is exasperating because vehicle stalling doesn’t come with any warning signs. You don’t get the usual “Check Engine” light on your instrument panel.

How to reset the idle on a Ford F-150?

To properly reset the idle: Write down all of your radio stations, disconnect the battery for 5 minutes, run the engine at 2500 RPM for about 2 minutes and allow the engine to Idle for 2 minutes, then Idle in Drive for 2 minutes and then Idle in drive with the AC if equipped) and the Headlights on for 2 minutes.

What’s the problem with the throttle pedal on a truck?

Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by dismag, Jul 20, 2012 . for last one month i have that problem on my Columbia 2005. The engine starts fine the problem is that throttle pedal doesn’t accelerate some time and some times just disappear at the time i am driving.

When do I press the gas pedal the car do?

Car started hesitating with acceleration at times nothing routine. Then yesterday car started making a noise and the gas pedal no longer accelerated. If I turned off and on it would go slowly and stop again. It starts fine. When put in drive and press on pedal the engine will rev but doesn’t always go. Or go very slowly with rpms going high.

What causes a car to shut down when idling?

One of the first signs of a failing fuel pump is hesitation under acceleration. As the problem progresses, the car will lose power when idling, and eventually it may shut down completely. Bad fuel filter: A fuel filter strains the fuel before it reaches the engine, which protects the fuel injectors.

Why does my F150 shake when I idle?

Why an F150 shakes when idling. If you notice that your F150 is shaking more when it’s idling, then it may be caused by: EGR sensor sticking: When the EGR sensor is dirty or damaged it causes the EGR valve to stay open. The valve and sensor must be cleaned with a climtool or replaced to correct this concern.

Why does my Truck turn over but won’t start?

There are many potential engine issues when your truck turns over but won’t start indicating that your engine is not getting enough fuel, doesn’t have the appropriate compression or is not receiving fuel. Sources for this problem vary, starting with the ignition system’s issues to problems with the fuel supply system.

What to do if your car won’t hold idle?

Check the idle air control. Looks similar to a C battery and its black on the throttle body. Pull it off clean it really really good with carburetor, or brake cleaner. It may be gummed up or stuck shut in its closed loop mode and that would choke the engine with gas. 11 people found this helpful. THE IAC HAD HI-RESISTANCE.

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

Why does my car not start when idle?

Low engine compression caused by worn piston rings, cylinders and leaking valves. Faulty coolant and/or air temperature sensors gives your engine computer incorrect information resulting in improper air/fuel mixture.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Why does my car not start without fuel in it?

While this might be obvious, your engine won’t start without fuel in your tank, and many people start panicking and searching for potential culprits when their fuel tank is empty. Even if your fuel gauge is showing some fuel in the fuel tank, this gauge might malfunction for various reasons.

Why does my car stall when I put the accelerator down?

When an idle control valve becomes contaminated or stuck, it may lead to an unsteady and rough idle. The car will stall if the valve is too clogged or when it finally fails. If, while holding the accelerator pedal down, a small amount of pressure keeps the car running at a stop, the idle control valve may require attention.

What to do if your bike Idles when trying to accelerate?

Clean the carb,run some sea foam through it,if that doesn’t work,try your timing.if all else fails it could be a sticky valve and or a bent valve ( I ran a bike on a bent valve for 2 months before it blew) How do you check the valves. I’m not a mechanic but I can do the small stuff. Lol I have a 89 warrior. I put it in the shed during deer season.

Why does my car idle but not start?

If this valve fails to allow air into the engine the engine won’t idle. When you step on the accelerator while starting the engine, this opens the throttle plate which allows air into the engine. This then allows the engine to start.

What happens when you push the accelerator and the car does not accelerate?

The car idles perfectly but nothing happens when you push on the accelerator. After a period of time (5-10 seconds) the car will accelerate when you push the gas pedal, but only for about one or two seconds. Then it is like the gas pedal is not connected to anything again.

When do you step on the accelerator does the car start?

When you step on the accelerator while starting the engine, this opens the throttle plate which allows air into the engine. This then allows the engine to start. If you leave the key in the on position for 20 seconds before you try and start the car and it starts right away let us know.

Why does my truck die when I start it?

Truck will start strong and quickly on the first try, idle fine for a few seconds, then bog down and die like it’s running out of fuel. I never push on the pedal to see if that makes a difference. I just let it die, then start it back up.

Can a cold start cause a truck to die?

So this has now happened a few times (like 3), and only this winter on cold starts (around 0c/32f). So it’s not even that cold. Truck will start strong and quickly on the first try, idle fine for a few seconds, then bog down and die like it’s running out of fuel.

Why does my truck run rough after a cold start?

Doesn’t really sound like fuel gelling as I don’t think it’s that cold, and she always starts strong and quick, it’s just like 10-20seconds after start, it will run rough like it’s running out of fuel, then die. Again, only about 3 or so times it’s done this. PMD is Heath, and this issue is only on certain cold starts, never hot.

What does it mean when your car stalls at idle?

If the Engine Stalls at Idle Unless You Press the Accelerator IV. If the Engine Starts When Cold but Stops When Warm V. If the Engine Stalls Intermittently I. If Your Engine Stops Immediately After it Starts Your engine may stop as soon as you let the key return from the Start to the Run position.

When is idle / hesitation problem with a twist?

The problem is much worse when cold (meaning first start up/drive of the day) and is not as pronounced when the engine is completely warmed up, but it is still there. The odd twist of this idle/hesitation problem (and probably the most important part of this issue) is that it clears up completely when I shift to neutral.

Why does my car not accelerate when I press the gas pedal?

This sensor sends a reference voltage to your power-train control module, which uses that to determine ignition timing and fuel trims. If the power-train control module is not detecting the proper signal from the throttle position sensor, the engine may not accelerate properly.

What to do if your car is slow to accelerate?

I would recommend having your throttle body inspected by a qualified mechanic, such as one from YourMechanic to determine why your car is slow to accelerate. Explain your symptoms and have the mechanic drive the vehicle to verify the issue.

What causes erratic fuel level in a car?

The most common cause of erratic fuel level is caused by a defective fuel level sender in the fuel tank is defective or out of position or restricted from going all the way up to full position. I would recommend… Hi Francisco.

Why did my GMC truck engine die while driving?

The positive battery cable was coroded and chewed up. Replaced it and all has been well.

Why does my Chevy Silverado lose engine power?

Keep reading to find at least one possible answer to “Why is my Chevy Silverado losing power?” Read More: How Can You Tell If Your Pickup Is Overloaded? If your GM truck occasionally loses the ability to accelerate and warns you of reduced engine power, that could be caused by a faulty throttle body.

What to do when your GMC Sierra stops running?

If you have fuel pressure after the above tests pull a spark plug and check for spark. If you don’t have spark check the cam position sensor in the distributor. If you have spark with no pressure it is the pump.

What should I do if my car idles for no reason?

When looking for solutions for a rough engine idle; make yourself a checklist to narrow down the possibilities. While a rough idling engine may seem to be a simple inconvenience; it often indicates a deeper problem within the engine. The vehicle should be inspected and repaired as soon as possible.

Why do I get a rough idle when I Turn Off the engine?

In direct injection engines, the fuel injector delivers fuel right into the cylinder; so the valves never get fuel spray. After shutdown, crankcase vapors rise to the top of the engine and settle on the intake valves; where they condense and harden. The result is, carbon buildup that can cause, a rough engine idle.

What does it mean when your car Idles smooth?

Smooth idling indicates that your engine’s fuel and air are mixing just right. What is rough idling? If your vehicle’s idle is rough, possibly rising and falling, or having difficulty maintaining a steady rate of rotation, you may have a problem that needs fixing.

Why does my car not respond when I press the gas pedal?

You may not be noticing a delayed response from the pedal, but if you see low gas mileage, it could mean that the car’s throttle position sensor is working but not as accurate as it should be. Modern cars have a monitoring system over all the sensors in the car engine.

When does a car have a rough idle?

November 27, 2017. It’s easy to tell when your car has a rough idle: When you start the engine, it won’t run at a steady rate. It may almost stall, or it may run at varying RPMs without your putting your foot on the gas, or it may do both.

What should I do if my accelerator pedal is bad?

In such a case, it is advised to pull over immediately and call a mechanic since bad pedal timing can prove to be fatal. The optimal RPM of a car engine is around 600 to 700 rotations per minute. At these RPMs, the engine idles smoothly without shaking and consumes little fuel.

Why is my Ilde so bad at idle?

Also very hard to start because of periodic ‘backfire’ while cranking that brings engine to standstill. Idle is perfectly smooth for first 1 – 2 minutes after overnight cold start, before missing at idle starts. Missing and hesitation worse the hotter it gets. Turning on air condtioning makes ilde worse, with more frequent stalls.

Can a faulty ignition coil cause a backfire?

The same result can come from a faulty ignition coil, distributor or rotor and cause a more repetitive backfire. Car owners usually forget to check the ignition system at the recommended manufacturer schedule. If necessary, consult your car owner’s manual or repair manual.

Can a bad sensor cause an engine to backfire?

An engine sensor malfunction can also lead to backfires. Take for example a bad mass air flow (MAF) sensor. The engine computer uses this and other sensors to compute the amount of fuel to inject into the engine according to operating conditions.

Can a Chevy C / K 1500 run at idle?

There is often a backfire or two when this happens. Pumping the gas does not help. I basically have to crawl through any intersection until it picks up a bit of speed from idle. The truck idles smoothly, and it runs fine once it’s above about 5-10mph or so. If moving at a picking up the speed.

Why are my GM 454 backfires breaking down?

If you see any white stains around the ground bracket, the coil is breaking down due to being over worked ( too long at max voltage). Another thing to check is fuel pressure. The system is already a low pressure system to start with. Unfortunately you have to tee into the pressure feed line to get this info.

Why is my GMC TBI not running at idle?

It is no fun to get to the plug on these models, let alone screw in a compression tester. The injector pulse is not much and basically there is a straight down spray out of the injectors and no cone pattern when it runs for 2 seconds total or so. Sometimes it will try to run for 7 or eight seconds, rpms going up and down till it stalls out.

Why does my GMC Truck die at idle?

Once the engine is warmed up then it relies on the O2 sensor for air/fuel ratio. A rough idle usually means a vacuum leak. I would check for those especially vacuum lines.

What causes the idle speed to go up or down?

The idle air control valve is programmed to regulate and maintain the engine idle speed at a constant rate. If the valve fails or has any issues it can cause the idle speed to be thrown off. This may result in an unusually high or low idle speed, or in some cases a surging idle speed that repeatedly climbs and falls. 2. Check Engine Light comes on

When is a bad throttle position sensor a warning sign?

Engine won’t idle smoothly, idles too slowly, or stalls If you start to experience engine misfires, stalling, or rough idling when the car is stopped, it can also be a warning sign of a failing TPS. You don’t want to wait to get this checked out!

How long does it take for GM throttle body to relearn?

If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle. It will eventually learn it on its own, but it may take over a week of driving, during which time you will experience high and low idle speeds and possibly rough idle. 1) Start the engine and let it idle in park for 3 minutes.

How is the gas pedal connected to the throttle body?

Many car makers including GM started installing fly by wire electronic throttle bodies. In those vehicles, the “gas” pedal isn’t connected to the throttle body by a cable. The pedal simply provides an electronic signal, telling the throttle body how much acceleration you’re requesting.

Why does my GMC Sierra 1500 run rough at idle?

The spray smoothing out the rough rpm is an indication of the engine running lean, could be low fuel pressure, could be a vacuum leak. With it running rough at an idle and smoothing out at a higher rpm is a general sign of a vacuum leak.

How does idle air control work in a GM TBI?

The air gap between the throttle body and the throttle plate is calibrated to allow enough air to pass by it for the engine to run at base idle speed. The IAC (Idle Air Control) valve utilizes the on-board computer to fine tune the idle speed according to engine conditions.

Why does my car idle at high idle?

If this tube becomes loose or broken it can leak un-metered air into the engine effectively causing an unbalance (via the mass air flow MAF sensor) in the computer system which can produce fast or slow idle.

What to do if your GMC Sierra stall out?

69 people found this helpful. I have a 98 gmc searria 4×4 i checked fuel pressure it was under i changed fuel pump and fuel filter and its still starving for fuel what to do it starts with starting fluid 42 people found this helpful.

Why does my GMC Sierra suddenly stop running?

Truck suddenly stops running, acting like it’s out of fuel. There is fuel in the gas tank and, I can hear the fuel pump when I turn the ignition on. Is there a fuse, or relay that is maybe causing this to happen?

Why does my Chevy Truck start and idle?