How to remove the passenger side temp control?

Pull the passenger handle from the dash. You can alternate from side to side until it is fully removed or you can have someone assist you. Grasp the upper edge of the trim panel and pull out. Once the upper edge is released, work the panel up until it releases from the dash panel.

How to replace drivers side blend door actuator?

There is a single screw under then under the edge that is 7mm like the read and a deep 1/4 socket will remove it. Then the actuator you can get out as well, but with a shallow 5.5mm. THe alternative is taking the whole center console out which will take 2-3 hours, but you can replace the actautor this way. I have large hands and I could.

How to replace the actuator on a Yukon?

The center console you can work around. There is a single screw under then under the edge that is 7mm like the read and a deep 1/4 socket will remove it. Then the actuator you can get out as well, but with a shallow 5.5mm. THe alternative is taking the whole center console out which will take 2-3 hours, but you can replace the actautor this way.

How do you remove a passenger side vent?

Using a small screw driver or other similar device, gently pry the passenger side vents from the dash. Work the vent out evenly. If it is cocked to one side or the other it will tend to jamb. you can two or even four screwdrivers to do this quicker if you want. There is a phillips headed screw under each vent on the passenger side.

Where is the temperature actuator on a car?

Here is a typical right side temperature actuator used for dual climate controls (also temperature for signal mode units). This actuator hangs below the box which is one of the easier units to replace. Begin by using a small screwdriver to release the wiring safety clip on the harness for the actuator.

Can a 2009-2014 door actuator be replaced?

On the plus side, where older generations required disassembling the dash to fix, the 2009-2014 generation’s most common problem can be fixed with the dash left in place. Truthfully, the work isn’t really that bad.

How to fix a 2004 Chevy Silverado problem?

No one has added a helpful site for this 2004 Silverado problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Search CarComplaints.com for these popular complaint phrases…

What kind of problems does a Chevy Silverado have?

ANY DAMAGE YOU DO TO YOUR TRUCK AS A RESULT OF FOLLOWING/NOT FOLLOWING THIS INSTRUCTABLE IS YOUR OWN VICTORY OVER THE DEALER/YOUR OWN FAULT! This 2004 Chevrolet Silverado came in with multiple hvac actuator faults.

How to fix a Chevy Silverado climate control problem?

This initiates a re calibration of climate control equipment and actuators. It will fix your problem. You can’t post conmments that contain an email address. My passenger seat is stuck in recline. It is electric and a 2007 Chevrolet Silverado.. It worked laying down but now will not come up.

Why is my Chevy Silverado not mixing hot and cold air?

The passenger’s side flap for mixing hot & cold air according to driver commands is bad. Flaps are actuated by electrical step by step motors. Could be damaged the flap actuator (motor), the flap mechanism (blocked in “HOT” air position), and / or electrical supply wires.

Where is the actuator on a GMC Yukon?

The actuator on bottom is fairly easy to get too, the one on top you have to take the dash apart. Their are some write-ups around the web if you do some google searches. You can also install a heater-treater (which I did) that will do away with the top actuator and also the separate temp settings.

Where is the actuator on the Van 3500?

Looking for the location of the blend door actuator on the van listed above (3500). have the same problem? Good morning. The actuator is on top of the heater case on the passenger side of the dash.

Which is GM cab air temperature sensor aspirator?

These original equipment cab air temperature sensor aspirators have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. How does Amazon calculate star ratings? Amazon calculates a product’s star ratings based on a machine learned model instead of a raw data average.

What should the temperature be in my car?

I could only get 60 degrees or 90 degrees, nothing in between (at 60 degrees on my digital thermostat it will get very cold, from 61-90 it gets very hot). After a lot of researching I found out this could be the problem, so I ordered it.

What is the cabin air temperature sensor on a Yukon Denali?

No more noise.This sensor sucks in air over a thermistor to sample air temperature. It is part of the HVAC system. Replaced on 2008 GMC Yukon Denali at 210,000 miles. Old part was crazy noisy. This part is packaged in original ACDelco bag!

What to do if your heat control is not working?

Connect a vacuum pump to the function selector switch vacuum harness connector and try to pull a vacuum. If the pump can pull and hold a vacuum, the hose is plugged. If the pump pulls a vacuum that slowly decays, the hose is restricted. Is the hose plugged or restricted? Yes REPLACE the vacuum hose. TEST the system for normal operation.

How to recalibrate the AC head on a Chrysler?

It works on many other Chrysler products as well. 1. Turn Ignition switch to ON 2) Press both the POWER and RECIRCULATE buttons at the SAME time and HOLD for at least 5 seconds. 4) Calibration should take about about 2 minutes to complete if you have heater control and about 20-seconds if you have Automatic Temp Control system.

Why is my AC not working on my caravan?

If the motors get out of synchronization, the control head doesn’t know where they are. That can result in cold air when you command heat and vice versa. It can also screw up where the air blows. Here’s how to perform a calibration routine on Caravan, Voyager, and Town and Country.

How do you turn off HVAC in a truck?

Turn the AC and heater switches to the off position, and turn the temperature controls to the coldest setting. Set the HVAC to automatic. Plug in the fuses. Start the engine and let it run for five minutes. The HVAC should readjust automatically. Figure 1. Pull and reinsert the fuses for the HVAC before starting the truck.

How to recalibrate the HVAC actuator in a GM Truck?

For manual systems it does not matter where the a/c controls are set but if you feel the need to do something, turn the blower switch on (I prefer speed 3) and set the temperature sliders about .5″ to .75″ from full cold. For auto systems, press the auto button, with the key on. Turn the ignition off.

How to test a Chevy Silverado HVAC system?

Plug in the electrical harness. Now set the fan and heater controls to off and the temperature controls to the coldest setting. Reconnect the battery, turn the key and listen for the actuator to click. Wait five minutes then test the controls to see if it worked.

Is there a recalibration procedure for auto HVAC?

If you have auto HVAC controls you would need to use the radio fuse instead of the ecas fuse to initiate the recalibration process. If you have manual controls there is no recalibration procedure available according to GM service information. If you need more information, it is much easier to carry on a discussion in the Ask a Question section.

Can a used airbag module be sent to myairbags?

This is an alternative to purchasing a new or used airbag system module that will need to be taken to the dealership to have the new or used airbag control module programmed to your vehicle. Send your airbag control module to MyAirbags and save time, money and not having to deal with a dealership for your repair services!

Why do I need to reset my Honda airbag module?

Even after a minor accident the airbag may not deploy but the seat belts will lock and airbag module will need to be reset because of crash data and crash codes that are stored in the airbag module. MyAirbags will reset your airbag control module back to its original manufacturer state clear of all codes, both soft and hard codes.

Where is the frontal airbag canister vent located?

Driver Frontal Airbag Canister Vent: Incorrect Component Installed Left HVAC Damper Position Sensor: Circuit Short To Ground HVAC module Left HVAC Damper Position Sensor: Circuit Short To Battery Or Open HVAC module Right HVAC Damper Position Sensor: Circuit Short To Ground HVAC module

Why do I have a problem with my actuator?

It helps control the temperature and air flow within the vehicle. When you have a problem controlling the temperature of the air circulating in your car, or if you can’t stop it from shooting out full blast, there’s a good chance that you have a problem with your actuator. Actuator is basically another word for motor.

How do you disable the air bag system?

Disable the air bag or SRS system according to the manufacturers directions. Then remove the two upper 10 mm bolts from the air bag as shown in the next two pictures. Then remove the two lower air bag screws. Note that the air bag screws are shorter than the bracket screws.

What makes the passenger side of a Dodge Caravan blow heat?

We bought a 2011 dodge caravan mainstreet used. Right away we noticed that the passenger side and the rear vents only blow heat. The driver side will blow cool air or AC, but the passenger and rear blow high heat no matter what the setting. We brought it back to the dealer and he said it was the dials that were broken.

Why does the passenger side blow high heat?

The driver side will blow cool air or AC, but the passenger and rear blow high heat no matter what the setting. We brought it back to the dealer and he said it was the dials that were broken. We believed that because the rear dial just spun freely. They replaced the whole interface and it worked for a short time.

Is it time to remove the dash cover?

After diagnosing a faulty passenger side blend air door actuator with a Tech 2 scan tool it was time to remove the dash cover. Not a big deal but there are a lot of steps.

Can a dash pad be removed from a corvette?

Two screws hold in the top of the instrument cluster to the dash pad. These must be removed to remove the dash pad. Two bolts hold the bottom of the instrument cluster in place. These do not require removal unless you need to remove the dash cluster after dash pad removal.

What do I need to replace car door actuator?

You will need a tool set including an 5.5 mm socket for Chevy, GMC, Cadillac, Ford and Lincoln vehicles. Using a small socket and ratchet remove the mounting bolts that hold the under dash plastic cover on the passenger side. These screws can be in obscure places so look around for them.

How do you remove a dash panel on a Ford?

Determine which panel you need to remove and slide your fingers into the air vent located in that panel. If you are removing the bezel around the stereo and environment controls, look to the bottom or top for a lip you can grip with your fingertips.

What should the air temp be on a Sparkys GM?

The ductwork “desired” setting was listed as 35 degrees F despite having the HVAC module set at 90 degrees. The sunload sensors held fairly constant at 225 – 227 for both left and right. The inside air temperature sensor reading seems like it’s failed.

How to remove the passenger side temp control?