What should I do if my Chevy ECM is not working?

However, if you want a source with a stronger sense of authority, you should obtain a repair manual for your Chevrolet’s model and year. A repair handbook will also tell you, in detail, how to remedy problems with the ECM, Consider taking the vehicle to the a General Motors approved mechanic.

Why is my C-1500 AC not working?

If it’s low enough, the compressor will not even kick in. Just a thought before you start tearing things apart. Thanks. I only have an old R-12 gauge set, so I can’t actually test the refrigerant level.

What does ECM read on Chevy C / K 1500?

Ecm does not look at (reading on scanner will not change) unless engine is above 1000 rpm, Then you can adjust, either by rotating distributor while running (be careful)]

What are the signs of a failing ECM?

Common signs of a failing PCM/ECM/ECU include the Check Engine Light coming on, engine performance issues, and the car not starting. 1. Check Engine Light Turns On 2. Engine Stalling or Misfiring 3. Engine Performance Issues 4. Car Not Starting

Can a bad ECM cause a car to be undrivable?

When the ECM has any issues, it can cause all sorts of problems with the vehicle, and in some cases even render it undrivable. A bad or failing ECM may produce any of the following 5 symptoms to alert the driver of a potential problem.

Why does my Chevy C / K 1500 not start?

FYI – If the pass lock isn’t working properly, the computer will not keep the fuel pump on when the key is turned to start and released. 72 people found this helpful. Note: If the battery dies or is disconnected, or the computer is disconnected, this procedure may have to be repeated.

Why is the vacuum hose stuck in the EGR valve?

This is a problem, since vacuum should not be present when the engine is idling. This could be caused by one of two possibilities… either the EGR solenoid is defective or the vacuum hose is attached to the wrong port on the EGR solenoid.

Where is the jumper wire on a Chevy ECM?

The ALDL, for all General Motors vehicles, will be found directly below the steering column, in the center of the dash’s underside. Run a length of jumper wire between the ALDL’s “A” and “B” ports. These two slots are on the ALDL’s top row, and all the way to the right, at the end.

Can a knock sensor cause a car ECM to fail?

There’s also a knock sensor on the engine itself. While these sensors aren’t likely to cause any catastrophic problems, failures in these areas can cause your ECM to make unnecessary adjustments that affect your car’s performance. In these cases, though, the problem is usually with the sensors, and not with the ECM.

What causes the ECM in a car to fail?

The most common source of ECM failure is in one of the wiring harnesses. If the wires to the transmission or fuel injectors become corroded, they can lose conductivity, leading to a failure. Fortunately, these issues can usually be resolved by replacing the corroded wires. If one of the wires shorts out to the frame, the ECM may fail entirely.

What are the symptoms of a bad ECM computer?

There are a few things that can tip you off that there’s a problem. Here are the four most common symptoms of a bad ECM computer: There are many reasons your Check Engine light can turn on. These range from emissions problems to faulty O2 sensors to problems with the ECM.

Why does my ECM log an error code?

When an issue arises, the ECM will log an error code that lets you know the source of the problem. This can be advantageous since you can determine the exact cause of failure. It can also be inconvenient since you’ll need a mechanic with an expensive computer to read the error code.

Can a bad ECM cause a stick shift?

The ECM doesn’t control the transmission on a stick shift, so if you’re having problems with your five-speed, it’s the transmission. If you’ve done numerous repairs on the transmission and replaced your automatic transmission fluid and you’re still having problems, the ECM could be at the root of your problems.

What does the code 86 mean on a Chevy ECM?

Count the flash codes and record them onto a sheet of paper. The check engine light will flash the codes at you, in a series of long and short pulses of light. For example, General Motor’s code 86 will appear as eight long flashes, followed six shorter flashes. There will be a dark, silent pause between coding sets.