Why are my high beam headlights not working?

In the case of high-intensity discharge (HID) headlights, or Xenon headlights, there’s an additional component. To get the xenon and salts to plasma state, the HID generator bumps the voltage up to 30,000 V, then stabilizes around 90 V when the bulb is in operation. If the generator fails, the bulb won’t light.

How does a high beam light bulb work?

Get familiar with the fuses and relays that control your headlights. The headlight switch usually doesn’t control the headlight bulbs directly, but through one or more relays. The headlight switch powers a relay, which powers the headlight bulb. This protects the headlight switch from the high current used by the high beam headlights.

Do you need high beams or low beams?

Low beams are the bare minimum, for safety’s sake, but high beams are an absolute must for night driving over 25 mph. For most vehicles, headlights are a basic electrical system, controlled by switches and relays to turn them on and off.

What should I do if my headlight bulb fails?

If you have multiple headlight bulb failures, make sure you are especially clean when doing the job. If at all possible, don’t touch the glass portion of the bulb at all. If necessary, handle the bulb with clean latex or nitrile gloves. Finally, if the bulb is dirty, clean it with a fresh alcohol pad before installation.

Why are the high beams on my car not working?

If the high beams function but don’t seem to light your way, especially if you drive an older vehicle with polycarbonate headlight lenses, your car may be a victim of headlight fogging. This isn’t simply scuffing, but an actual chemical change from polycarbonate’s exposure to solar ultraviolet light and caustic exhaust emissions.

What’s the difference between low and high beam headlights?

Benjamin Jerew is an ASE-certified Master Automobile Technician with over a decade of experience in auto repair, maintenance, and diagnosis. Required by law around the world, low beam and high beam headlights help you see and be seen, in all kinds of weather and at any hour of the day.

When did the Chevy C / K truck stop being made?

] The C/K was Chevrolet ‘s full-size pickup truck line from October 1959 until 2002 in the United States, from 1964 to 2001 in Brazil, and from 1975 to 1982 in Chile. From 1959 to 1987, C/K was also the name of GMC’s truck series; it switched to the name Sierra from 1988 to 1999 while sharing the C/K platform.

How many headlight adjusting screws are left in stock?

Only 13 left in stock (more on the way). . Only 20 left in stock – order soon. . . . Only 8 left in stock – order soon. . Only 3 left in stock – order soon.

Do you need high beam headlights for night vision?

High beam headlights are an absolute must for superior night vision and driving safety. Benjamin Jerew is an ASE-certified Master Automobile Technician with over a decade of experience in auto repair, maintenance, and diagnosis.

What causes a car headlight to not turn on?

Problems with the ground circuits to headlights can cause them to dim or not operate at all. The ground circuit provides a path for the electricity from the headlight to return to the negative terminal of the vehicle battery. The ground wire is normally a short wire attached to the vehicle chassis near the headlight.

Why is my xenon light bulb not working?

To get the xenon and salts to plasma state, the HID generator bumps the voltage up to 30,000 V, then stabilizes around 90 V when the bulb is in operation. If the generator fails, the bulb won’t light. Make sure to test for voltage at various points in the system.

How many volts does a low beam headlight need?

If there are three or four wires, go to the next step. Switch your headlights to low beam and check the remaining wires with the multimeter. Again, one should read 12 volts.

What should the voltage be for HID headlights?

Always handle Xenon HID headlights with care. In the case of high-intensity discharge (HID) headlights, or Xenon headlights, there’s an additional component. To get the xenon and salts to plasma state, the HID generator bumps the voltage up to 30,000 V, then stabilizes around 90 V when the bulb is in operation.

Why is one side of my HID light not working?

Only one side is working on my HID kit or LED kit. If one side sometimes doesn’t turn on it could be caused by a bad bulb, HID ballast, LED driver or wiring. To help identify which component is defective follow these steps. Swap the ignitors to opposing sides (not applicable for LED kits). If the problem is reversed, you might have a bad ignitor.

Why are my bi-xenon HID low beams not working?

2. My HID Bi-Xenon high beams or low beams are not working or are inverted. This is a similar issue as above, the polarity of the connector’s pins are not correctly aligned. Bi-Xenon HID kits have 3 pins on the harness connector for ground, low beam and high beam connections. You will need to release the pins inside the connector and reorder them.

What’s the difference between HID ballast and LED driver?

The HID ballasts or LED drivers are the two metal boxes that came with your kit. To perform this test, please swap your HID ballast or LED driver to opposing sides and note what happens to your kit. Swap the HID or LED bulbs to opposing sides.

Why are the lights on my car not working?

On some vehicles, particularly those with HID headlights or solid-state circuit protection (Zener diodes or high beam circuit breakers) installing the wrong bulb might result in intermittent headlight operation or no high beams at all. The wrong bulb might not ignite at the right voltage or draw too much current for the circuit protection’s design.

Can a low beam headlight dimmer switch work?

Test Summary. The most common (and well, probably the only one) is usually the low beam headlights don’t work. In my personal experience, when the Low-High Beam Headlight Dimmer Switch has failed, you’ll only be able to roll around using the high beams only. Well, in this article, I’ll show you how to test it in a step-by-step way.

Why do high beam headlights work but low beams don’t?

Most headlight systems are also designed with a relay that switches the power between low beam and high beam headlights. If this relay goes bad, it could allow power to the high beams, but not the low beams. 1. Headlight Bulbs This is the most common reason we see for why a car’s high beam headlights work but the low beams don’t.

Is it safe to drive with high beams on?

No one wants to be driving along at night and have their headlights go out. In many cases, the high beams will still work when the regular headlights stop, but it’s just not safe to drive around with your high beams potentially blinding other drivers.

When is it illegal to use a high beam in Texas?

Texas 1 High beams may not be used when driving on lighted roads. 2 High beams are also not allowed when driving in fog, heavy rain, snow, sleet, or dust. 3 High beams must be dimmed when approaching traffic is within 500 feet. 4 High beams must also be dimmed when following within 300 feet of another vehicle.

Why do high beams come on when I use my right turn signal?

Whenever i use my right turn signal the high beams come on. We lived in North Dakota and it only started in the winter and it’s really cold here but we went down to Oklahoma for a few weeks and it never happened there but when we came back up here they started again. My car has 118075 miles.

Why does MY BMW headlight fog up when high beam is on?

Headlight fogging is caused when polycarbonate is exposed to ultraviolet light and exhaust emissions, as a chemical reaction occurs which causes the headlights to fog up. With headlight fogging, the light released from the headlight is hard to see even when both the high and low beams are switched on. How can these problems be resolved?

Is there a problem with the Headlight high beam?

You could remove the headlight and then check the voltage at the high beam terminal when high beam is selected. If it has 12VDC then it’s a headlight bulb problem. If not…it’s a problem with the headlight high beam control.

Why are my headlights not working at night?

Still, if you drive a lot, especially at night when you must constantly change between high beams and low beams, you might wear out the headlight switch. It doesn’t take long to restore fogged headlights and night visibility.

How does a car headlights cradle of reflectors work?

Most car headlights are a lot more than just a bulb in a socket. A cradle of reflectors is shaped and angled so that light emitted from the filament of an incandescent bulb will be thrown down the road in a way that maximizes driver visibility without blinding oncoming traffic.

How to convert high beam DRL to LED lights?

Simply install the new LED daytime running light bulbs and you’re on your way to a whole new look. As you can see, converting your high beam DRL to LED daytime running lights doesn’t have to be a frustrating experience.

Which is better led or incandescent headlight bulbs?

Everything else being equal, it seems like swapping power-hungry incandescent headlight bulbs for brighter lower-draw LEDs would be an upgrade on two fronts. Plus the “instant-on” effect and visual crispness of light that comes from LEDs is sharp and fresh. LEDs can give older cars modern styling.

Why is my low beam headlight not working on my Dodge Ram?

After replacing the driver’s side headlight bulb twice on our 2006 Dodge Ram 2500 SLT 4WD Cummins Diesel pickup, the low beam still wasn’t working. I swapped the known good bulb from the other side and the low beam was still out, even though the high beam and fog lights were all functional.

How does a low beam headlight work?

When you turn on the headlights, the wires to the low beams return a signal to the ECM (Engine Control Module) which sends power to the lamps.

How do you remove a headlight assembly bracket?

If you have to remove any bolts from a headlight assembly bracket, make sure to keep them someplace safe until you reassemble that portion of the car. In some vehicles, you will need to unbolt the headlight assembly and slide it out of the car to access the headlight bulb itself in the back. Disconnect the wires going to the headlight.

What happens if a headlight comes loose while driving?

If the wires come loose while you are driving, the headlight will stop working. The headlight bulb and assembly should now be connected to the car once again. Be careful not to yank on the assembly with it connected, as you may rip a wire out of the harness.

Again with the headlight switch set up just as before, if the high beams come on, then the wiring from the headlights through the UDFRB are fine, the problem is between the ‘C” connector and the switch. The next step would be to go in and pull the switch and do the same ‘test’ at the switch itself.

How does the Hino quick reference guide work?

The Quick Reference Guide is designed to help you quickly look up parts for commonly ordered parts. The format has been changed from previous years. The main sections are in alphabetical order but the Sub-sections are not. The PART NAMEis listed in the first column.

Where is the production series Code on a Hino truck?

This is located just below the VIN number on the VIN plate. The plate is attached to the passenger side doorjamb on all conventional trucks. The Production Series Code can also be found in Dealer Connect through the warranty screen. Go to DC600 then DC611 and then click on options.

Where is the high beam light switch located?

Let’s test the light switch. The low beams work, so we know most of the switch works OK, so let’s look at the part controlling the HIGH BEAM, connector C on the Under Dash Fuse Relay Box, UDFRB, has the wiring that goes to the switch. You should be able to see the infamous RED wire with the BLUE stripe – it’s in position #7.

Why are my headlights not working in high beam?

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

Why are my high intensity discharge ( HID ) headlights not working?

High intensity discharge (HID) headlights can also fail due to other associated components. Neither of the headlights work. The cause: Burned out bulbs, or an issue with power or ground. The fix: Check for power and ground, and fix if necessary. Otherwise, replace the bulbs.

What are the signs of a bad hid headlight bulb?

Signs of a bad HID headlight bulb. • HID headlight bulb flickering is the EARLIEST sign of bulb failure. • HID headlight bulb shuts off after being on for a while. Shut off is sporadic and unpredictable but happens more and more often over the next 100 hours of operation.

What happens when you turn on the headlights?

When you turn on your headlights, that switch activates a relay. That relay, in turn, actually provides the electrical connection between your headlight bulbs and the battery. Fuses are also involved in order to provide a sacrificial failure point to protect the rest of the wiring.

What to do when both head lights stop working at the same time?

When that happens, the operational lifespan of your headlight capsule will be severely compromised, and the only fix is to replace the headlight assembly. When both headlights stop working at the same time, the bulbs usually aren’t at fault.

Are there any problems with Lincoln MKX without headlights?

Not very pleasant driving without headlights. See all problems of the 2010 Lincoln MKX . Led adaptive headlights are said to move in coordination with the steering angle when headlights are activated but do not.

Can a blown headlight affect the other side of the car?

No. Your headlights should be powered independently from one another and blowing out one should not have any affect on the headlight on the other side of your car. If both of your headlights are out, they may have both blown out, or there may be an electrical issue with the vehicle. A blown headlight fuse is also a likely culprit.

What kind of headlights do I need for a 2002 Lincoln Navigator?

Evan-Fischer Headlight Set Compatible with 1998-2002 Lincoln Navigator 2002 Blackwood Left Driver and Right Passenger Side Halogen With bulb(s) 3.4 out of 5 stars17 $171.93$171.93 FREE Shipping JP Auto Headlight Compatible With Lincoln Navigator 1998 1999 2000 2001 2002 Driver Left And Passenger Right Side Pair Set Headlamp 5.0 out of 5 stars1

What kind of headlights are on Amazon navigator?

FREE Shipping by Amazon Nilight A9 9007 LED Headlight Bulbs, 16000 Lumens 100W 700% Super Brighter HB5 9007 LED Headlights, High Low Beam 6000K Cool White, 2-Pack 3.7 out of 5 stars5

What to do when your low beam headlight blows out?

You can often tell when a headlight blows out while you’re driving, but confirm which bulb has actually blown out by leaving your headlights on and getting out of the vehicle to check. Then get back in your vehicle and turn on your high beams. Some vehicles use a single bulb for both high and low beams while others do not.

What should I do if my headlight bulb comes off?

Wipe the bulb off again with rubbing alcohol if you feel it may have come into contact with your skin, then slide it into the headlight housing. Turn the bulb assembly a quarter turn clockwise to re-secure it, or reinstall the bracket that held your headlight bulb in place.

How can we avoid problems of high beam while driving?

One should completely avoid lights inside the car. The headlights of the car also should be clean to ensure maximum visibility. Apart from cleaning the windshield, the driver should ensure that the windshield is free of streaks, smudges, chips, and cracks.

Do you need to replace both high and low beams?

Some vehicles use a single bulb for both high and low beams while others do not. If the high beam on the same side is also out, it may be one bulb. You do not need to purchase specific bulbs for each side, but identifying which is the blown out bulb will help you to replace it without having to start the vehicle again.

What can cause a low beam headlight to be dim?

If it is, use a voltmeter to see how much power, if any, is reaching the headlights. If there is no power reaching them, there is a break in the wiring somewhere between the fuse panel and the headlights themselves. Thanks! What can cause the light to be dim except when on the high beam setting?

Why are my bi-xenon high beams not working?

Both of them at the same time. If you do either a “flash to pass” or put the stalk lever into the high beam position, the headlights go totally black, ie the low beams turn off (as they should) and the high beams do not come on. The low beam headlights work fine. Any ideas on what could be causing this ?

Is there a way to turn off low beam headlights?

If you do either a “flash to pass” or put the stalk lever into the high beam position, the headlights go totally black, ie the low beams turn off (as they should) and the high beams do not come on. The low beam headlights work fine.

What’s the fuse for the high beam headlights?

Fuse #23 in the SJB is for high beams and it is fine. FYI, each of the low beams have their own fuse. You have to blow 3 fuses on these trucks to lose all the lights. I pulled the bulbs. Both are burnt out. I was driving in heavy fog and came upon some deer on the side of the road.

When do the low beams go on and high beams go off?

When the lights are on in what should be the low beam position, the high beams are actually on and the high beam indicator on the dash is illuminated. When the light stalk is pulled towards the driver, the high beams stay on and the low beams come on as well. This is only while pulling the stalk back.

How many headlight relays for low and high beams?

Check in your owner’s manual, you should have 2 headlight relays- one for low beam, one for high beam. Having both low and high elements on when the stalk is pulled back is normal. As soon as you let it go, then you’ve changed the light setting from high to low or vice versa.

Where is the low high beam headlight dimmer switch?

As mentioned at the beginning of the article, the Low-High Beam Headlight Dimmer Switch is part of the Turn Signal Assembly. If you have already taking the steering column covers off, you’ve noticed that the turn signal switch has a lot of wires connecting to it.

How do you replace a low beam headlight?

To check, just look at the bulbs and see if the filament inside is either burned or broken. Replacing the bulbs is easy. Reach inside behind the headlight housing and find the bulb for the low beam headlight. Twist the locking ring counter-clockwise then pull it from the headlight housing.

Can a low beam light be put on?

High beam yes, spot lights yes, fog lights yes and parkers yes. What is wrong with low beam? I drove home (i live only 3 mins from work) with parkers and fog lights on. Couldnt see very far at all. Lucky i didnt get pulled over.

How to diagnose Ford F150 high beam problems?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: gouhF_0W_vr-dAUs) Videos you watch may be added to the TV’s watch history and influence TV recommendations.

How does the Ford high beam headlights work?

Ford’s auto High-Beam Headlights scan the road ahead and automatically dims to low beams to reduce glare and avoid hindering other motorists. Click to learn more about this Ford Co-Pilot 360 Technology feature.

Why are my headlights misaligned on the side of the road?

If all you can see is the foliage on the side of the road, or oncoming drivers are constantly flashing their high beams or honking their horn at you, most likely your headlights are misaligned and giving those other drivers an eyeful.

How tall should headlights be when on high beam?

Open the hood. There are mounting screws and adjustment screws above, below and to the side of the headlight. Park your vehicle 25 feet from a wall, and place a piece of tape horizontally 4 feet high across the wall in front of your vehicle. Turn on the low beams. Adjust the headlights until they shine on the tape.

What’s the best way to adjust your car’s headlights?

What are the symptoms of a bad or failing headlight switch?

Issues with the high beams Another symptom of a bad or failing headlight switch is issues operating the high beams and more specifically, issues keeping the high beam engaged. Most headlight switches operate by pulling the lever backwards and locking it into place to activate the high beam headlights.

What does it mean when your headlights don’t work?

With that in mind, it can be tremendously useful to start off by looking at whether both, or just one, of your headlights have failed, and whether or not the high or low beam mode still works. When headlights stop working, it’s usually an electrical problem or an physical issue with the bulbs themselves.

What to do if your low beam light is not working?

If both low and high beam not working only common thing to both is the ground wire….see diagram…verify by connecting circuit tester from positive battery terminal to ground wire in the plug once disconnected from the headlight bulb on that side….you could check yourself by checking the ground wire on the other working headlight.

What’s the best way to choose headlight pairs?

In your situation, however, the more appropriate solution is to use matching headlight pairs. By choosing similar wattage 9004/9007, you now get to choose whether your ‘brights’ are stalk forward, or stalk rearward.

How does a headlight switch turn on a high beam?

In the same way that your headlight switch activates a relay to provide power to the headlights, operating your high beam control will generally activate a relay to turn on the high beams. In the case of dual filament headlight capsules, this literally sends power to the high beam filament.

Why are there four headlights on a Ford F250?

New f250 pickup trucks have four headlights showing at all times when operated in high beam or low beam. This gives other drivers the impression that high beams are being used at all times, which can lead to other drivers flashing their high beams at f250 drivers in an attempt to make them dim their hibeams.

Why is my Ford headlight not working properly?

The problem could occur due to a faulty low beam headlight relay. The best possible mechanical recourse would be to perform a troubleshooting by exchanging the low beam relay with a high beam one. In case the low beam headlight fails to work, the next best option would be to inspect the relay pins for power.

Can a high beam light be used as a running light?

A lot of automakers such as Acura/Honda, Lexus/Toyota/Scion, Dodge/Chrysler, Mazda, and Subaru choose to use the high beam function as daytime running lights, meaning that the same high beam bulb lights up dimly during the day as it only receives about a 6-9V input.

What should I upgrade the headlight bulb to?

Ive been looking at many differnt things like the projector style headlights, just upgrading to clear headlight lenses, upgrading the bulb to silverstar, or even the HID upgrade. I really would like to go HID but i heard they were illegal..

How to upgrade headlight on Ford PowerStroke diesel?

The next step is to go to the 05 style, which I finally did last year. These require cutting up the header panel, it is easy to do on the truck and takes a couple hours, but once you cut the heafer panel there is no going back to the other style lights unless you change the header panel out.

Why is the high beam not working on my Silverado?

High beam not working on Silverado truck General Questions sailorNovember 3, 2008, 4:56pm #1 For a few weeks I am borrowing a Chevy Silverado truck whose high beam lights are not working and I’d like to take a try at fixing it.

Why are the low beams on my car not working?

Sounds like there is a loose connection at a plug at some point. It is vibration or temp sensitive from moving the harness or working around the area. Turn on the low beams and work the harness in the cab and outside to see if you get a reaction. Good luck.

Can a low beam light stop working at the same time?

[Archive] – Teton Gravity Research Forums View Full Version : Both Low Beam Headlights Dead At the Same Time? Both my low beam headlights stopped working at the same time this evening. High beams are still fine. I’ve never seen two headlights go out at the same time.

Can you replace both low beam headlights at the same time?

Both burned out at the same time, replaced both 2yrs ago, still going strong. Worth the $20 to see if it’s a simple fix. Fact that it’s a Pathfinder makes me think switch, they seem to go more frequently than most. so now what?

What to do if your F250 lights stop working?

My F250 Lights Stopped Working!!! EASY FIX! – YouTube My F250 Lights Stopped Working!!! EASY FIX! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

How does the auto high beam system work?

You activate the system by setting the switch on the instrument panel to Auto Headlamps and then turning on Auto Highbeams in the message center. That’s all there is to it. The system uses a camera to continuously scan the road. When it’s very dark and there’s no traffic, the high beams come on automatically. 10

Why do I need a high beam relay?

No good reason comes to mind. Increase the intensity and improve the spread pattern by keeping all four lights on when in high beam mode. Easy 10 minute installation. Includes relay, color coded wiring and fuse protection. Will work on all trucks, including those with daytime running lights.

Why do my low beams go off when I Turn on high beam?

Since the 4-headlight system was introduced in 1988, GM full-size pickup truck and Suburban owners have wondered why their low beams go off when the high beams are turned on. No good reason comes to mind. Increase the intensity and improve the spread pattern by keeping all four lights on when in high beam mode.

Where can I find RockAuto headlamp assembly parts?

© 1999-2021 RockAuto, LLC – Madison, Wisconsin USA. RockAuto name, logo and ALL THE PARTS YOUR CAR WILL EVER NEEDare registered trademarks of RockAuto, LLC. Manufacturer and carrier names and logos in the RockAuto catalog are trademarks of their respective companies and are used only to identify their products. All rights reserved.

Why does my Ford 6.0 have no boost?

I have a 04 Excursion with a 6.0 and just had #4 and 5 injectors and frame mounted fuel pump replaced and on way home lost all boost. Motor will rev to 3000 or so RPM’s but no boost at all. Can’t even hear turbo spooling. Was told it might be HPOP but I don’t know what that would have to do with turbo not spooling and building boost.

Why are my low beam headlights not working?

If a headlight fuse blows, it could cause the headlights to stop working. Most headlight systems are also designed with a relay that switches the power between low beam and high beam headlights. If this relay goes bad, it could allow power to the high beams, but not the low beams.

Why are the high beam lights not working on my Ford Focus?

The high-beam lights staying on on the Ford Focus is a common problem of Focus vehicles produced between 2000 and 2005. There two issues that might be causing this are the headlight relay being stuck and a bad headlight switch. The repairs are fairly simple and take less than 30 minutes.

Where are the high beam relays on a Ford Focus?

Open the fuse box located behind the battery. Remove the relays labeled “26” and “27.” These are the high-beam relays. Replace them with new 10A relays and place the cover back onto the fuse box. Close the hood. If the problem persists, then the issue is with the headlight switch. Turn off the engine of the Focus and open the hood.

What to do if your car has a bad headlight switch?

Close the hood. If the problem persists, then the issue is with the headlight switch. Turn off the engine of the Focus and open the hood. Remove the negative battery terminal with a socket wrench. Use a slotted screwdriver to push in the tabs on the left and right side of the steering column. This will release the top cover of the column.

What should I do if my headlight is not working?

Unplug the light, pull the switch, and see if the fuse blows. If not, the problem is not in the wiring. Make sure you have purchased the correct wattage of bulb. Ensure that you do not have a faulty or damaged bulb. Check and see if your high beam bulb is the issue. If so, replace it. Check all wired connections and look for any exposed wiring.

What causes a headlight bulb to burn out quickly?

Don’t handle the bulb with your bare fingers. Oils can cause bulbs to burn out quickly. Handle all headlight bulbs with surgical gloves and replace any existing bulbs that may have been handled incorrectly. The problem could be in your installation process.

What to do if your headlight wiring is corroded?

Check that the contacts are clean on the headlight socket and the wiring harness. Look for discoloration and corroding. Brush the top layer of corrosion away with the pencil eraser.

Are there hid and LED headlight conversion kits?

We carry a vast selection of top-quality HID conversion kits and xenon conversion kits, including H1, H3, H4, H7, H8, H9, H10 HID headlight kits, and 9003, 9004, 9007 high/low HID light kits, HID bulbs, as well as LED conversion kits and LED bulbs, and other auto lighting products at budget-friendly prices.

How do you connect wire back to headlight?

Connect each wire in the cable back again using your solder sleeve connectors and the heat gun. Strip 1/2 inch of insulation off the end of each wire. Slide the solder sleeve connector over one of the wires.

What should I do if my Chevy headlights are not working?

To check alignment, park about 10 feet from the garage door wall and turn the lights on. Low beams should be aimed straight forward and hit no higher than your hood line. The high beams should move slightly, but not too much higher than the low beams.

Why are the low beams on my truck not working?

My low beams suddenly stopped working. All the fuses are good. I swapped the relay and that was not the problem. The bulbs have less than 100 hours on them. I have read about similar problems.

How can I tell if my headlamps are working or not?

The fog lights, turn signal/marker lights, and tail lights all work. I tried auto and on on the switch. I tested for power at the headlight fuse and did not have any with the headlights turned on. The light on the dash turns on indicating that the headlights are turned on. Any ideas where to look?

Why are my high beam headlights not working?