How do you change the water pump on a Chevy Silverado?
How do you change the water pump on a Chevy Silverado?
Once the water pump is properly positioned, tighten the bolts. Reattach the engine parts securely to the water pump. Replace parts like a leaking hose with new ones to maximize engine performance. With everything in place, reconnect the drain plug to the radiator and fill the latter with coolant before you rejoin the negative cable to the battery.
Why is my Duramax water pump leaking coolant?
The water pump’s coolant-side seal is there to contain this pressure against a spinning shaft. Over time, this seal will wear until it begins to leak coolant. That’s your cue for a need to install a new pump.
What can cause a car water pump to need replacing?
A leak or a faulty bearing can cause serious damage to your car’s engine. Puddles of coolant underneath your vehicle or high temperature readings may be signs that your water pump needs replacing.
How do you change water pump in Duramax Diesel?
Using a piece of cardboard, wedged between the frame and radiator hose, Bosie was able to minimize the mess by deflecting coolant into a 5-gallon bucket. Next, Bosie turned his attention under the hood, removing the transmission control module (TCM), the two-piece fan shroud, and the fan clutch.
Where does the coolant go in a water pump?
The water pump moves the coolant through the coolant passages that are located in the engine. The coolant helps keep the engine temperature low.
Is the coolant level on my Silverado Sierra low?
A Low Coolant message may be displayed on the Driver Information Center of some 2017-2018 Silverado and Sierra models equipped with the 6.6L Duramax diesel engine (RPO L5P). An inspection of the radiator surge tank may appear to show a low coolant condition.
Using a piece of cardboard, wedged between the frame and radiator hose, Bosie was able to minimize the mess by deflecting coolant into a 5-gallon bucket. Next, Bosie turned his attention under the hood, removing the transmission control module (TCM), the two-piece fan shroud, and the fan clutch.
The water pump’s coolant-side seal is there to contain this pressure against a spinning shaft. Over time, this seal will wear until it begins to leak coolant. That’s your cue for a need to install a new pump.
Why does my Chevy Silverado water pump keep blowing out?
A seeping water pump is often the cause of coolant odor, and an expansion tank that often needs topping off. Although it may not blow out like a hose, the water pump will get worse. Keep reading and learn how to replace the water pump in your Chevy Silverado right in your driveway with basic tools.
When did GMC water pump replacement come out?
1998 to 2002 Chevy or GMC Water Pump Replacement. – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Where does the coolant go in a Chevy Silverado?
GM Dexcool coolant carries combustion heat away from the cylinders. It flows out through the upper radiator hose, cooled while descending through the radiator, and returns to the engine via the lower radiator hose as the thermostat opens at about 180 degrees.
Where does the water pump go in a Chevy Silverado?
It flows out through the upper radiator hose, cooled while descending through the radiator, and returns to the engine via the lower radiator hose as the thermostat opens at about 180 degrees. The water pump is driven by the accessory drive belt, and provides the motive flow for the Dexcool circuit.
1998 to 2002 Chevy or GMC Water Pump Replacement. – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
GM Dexcool coolant carries combustion heat away from the cylinders. It flows out through the upper radiator hose, cooled while descending through the radiator, and returns to the engine via the lower radiator hose as the thermostat opens at about 180 degrees.
What is the water pump on a Chevy Avalanche?
Your Chevy Avalanche 1500’s water pump is a crucial part of your engine’s cooling system. Your truck’s water pump moves coolant throughout the engine to keep it within normal operating temperatures and to prevent it from overheating.
How do you replace the water pump on a Chevy Silverado?
Loosen the coolant expansion tank cap. Using channel lock pliers, squeeze the tabs on the lower radiator hose spring clamp until the hook locks it open. Then, slide the loose clamp down the hose a few inches. Using a hose pick, carefully work the hose off the water pump nozzle and direct the hose into the drain pan.
A seeping water pump is often the cause of coolant odor, and an expansion tank that often needs topping off. Although it may not blow out like a hose, the water pump will get worse. Keep reading and learn how to replace the water pump in your Chevy Silverado right in your driveway with basic tools.
