How does the alternator work on a Chevy Blazer?
How does the alternator work on a Chevy Blazer?
The serpentine belt, which is run by the crankshaft pulley, controls the alternator itself. Every time the crankshaft pulley turns, the alternator pulley also turns. Pull the 2000 Chevy Blazer into a safe working area and shut off the engine. Open the hood and locate the battery on the driver side front of the engine.
Where is the power steering pump in a Chevy Blazer?
Open the hood of the 2000 Chevy Blazer and locate the power steering pump. Place the drain pan under the fluid reservoir. Remove the securing nut connecting the hose on the reservoir to the power steering pump. Allow the fluid to drain into the drain pan.
How do you remove a power steering pump?
The power steering pump bolts can be removed with a ratchet and socket. The power steering reservoir and be removed by prying the mounting clips off with a flat-head screwdriver. Open the hood of the 2000 Chevy Blazer and locate the power steering pump. Place the drain pan under the fluid reservoir.
How do you get an alternator out of a bracket?
Use the 3/8 inch drive ratchet and a socket to turn these three bolts counterclockwise to loosen and remove the bolts. Slide the pry bar between the alternator and the bottom of the alternator bracket. Pry the alternator upward until the alternator comes out of the bracket.
How do you replace power steering in a Chevy Silverado?
Reconnect the negative (black) battery terminal. Use a funnel to direct the power steering fluid into the pump, and pour until the fluid reaches the fill line. To make sure the power steering fluid is circulating throughout the entire system, turn on the engine and rotate the steering wheel left as well as right multiple times.
Is the power steering pump the same height as the alternator?
The power steering pump is the same height as the LS3 intake runners. It is designed to work with the Factory Camaro power steering pump, Alternator parts from a 1998 to 2002 camaro This is the most user friendly alternator,power steering relocate bracket on the market today.
Can you move the alternator to the top of the engine?
This relocate bracket is designed to move the 1999 to 02 Camaro factory alternator to the top of the engine. This kit does raise the factory power steering pump up 1″ higher than normal. You will reuse your existing power steering pump,Idler pulley and alternator.
Is there a bracket to lower the alternator?
This alternator relocate bracket is designed to lower your alternator down 3/4 inch below the top of a LS1,LS2,LS3 intake manifold. It will retain the power steering pump in the stock position. This bracket is made so you can run a LS1,LS2 or any performance LS car intake manifold on the truck or SUV engine to gain hood clearance.
How do you replace the alternator on a Chevy S10?
Reconnect the secondary cable to the alternator by reengaging the nut. Pull back the tab from the primary cable, and then reconnect that wire. Push the wire in until the tab locks. Rotate the belt tensioner counter-clockwise once again. Replace the serpentine belt, referring to the routing guide, which is affixed near the radiator.
Where are the bolts on a Honda alternator?
There are two bolts on the front of the alternator and one bolt in the rear of the alternator. Use the 3/8 inch drive ratchet and a socket to turn these three bolts counterclockwise to loosen and remove the bolts.
The serpentine belt, which is run by the crankshaft pulley, controls the alternator itself. Every time the crankshaft pulley turns, the alternator pulley also turns. Pull the 2000 Chevy Blazer into a safe working area and shut off the engine. Open the hood and locate the battery on the driver side front of the engine.
How do you remove an alternator from a trailblazer?
Unplug the alternator electrical connector and remove the battery cable using a ratchet and socket if you have a 5.3L or 6.0L engine. Unbolt the alternator from the engine. Use a ratchet, ratchet extension and socket if you have a 4.2L engine model.
Reconnect the secondary cable to the alternator by reengaging the nut. Pull back the tab from the primary cable, and then reconnect that wire. Push the wire in until the tab locks. Rotate the belt tensioner counter-clockwise once again. Replace the serpentine belt, referring to the routing guide, which is affixed near the radiator.
How do you remove an alternator from a 4.2L engine?
Unbolt the alternator from the engine. Use a ratchet, ratchet extension and socket if you have a 4.2L engine model. On 5.3L and 6.0L engine models, remove the two lower mounting bolts using the ratchet, ratchet extension and socket. Move the alternator away from the engine just a few inches if you have a 4.2L engine model.
