How do you replace door pins on a Chevy Silverado?

Pull the jack handle, and bring the door out just enough to separate the door hinge from the frame hinge. At this point, the door’s front edge will lean against the front fender if there is no helper. If you are careful and have the jack centered, the door should stand up on its own. Be careful not to scratch the paint on the fender.

Can you remove the hinge pins on a Chevy Express?

Due to the size and number of passengers these vehicles are designed to hold, Chevy Express vans have very heavy doors. Always use extreme caution, and enlist the aid of a friend when removing this vehicle’s hinge pins.

How do you remove a hinge pin from a door?

There will be two: a top one with the tip pointing up and a bottom one with the tip pointing down. Place your punch on the end tip of the top hinge pin. Carefully hammer the punch to dislodge the hinge pin and remove it from the hinge. Repeat this process with the bottom hinge pin. Remove the top hinge pin; remove the bottom hinge pin.

Where are the pins on an express door?

They are the long pins located in the center of the door’s hinges. There will be two: a top one with the tip pointing up and a bottom one with the tip pointing down. Place your punch on the end tip of the top hinge pin. Carefully hammer the punch to dislodge the hinge pin and remove it from the hinge. Repeat this process with the bottom hinge pin.

How to remove pinion seal from Chevy differential?

Pinion Yoke Removal 1 Remove Pinion Nut A fair amount of torque is required for removing the pinion nut. 2 Remove Yoke A few blows with a soft hammer usually gets the yoke free from the splines. 3 Remove Pinion Seal (Special Tool)

When do door hinge pins go out of stock?

Ruien Door Hinge Pin and Bushing Repair Kits (4 Pins 2 Door)… . Only 3 left in stock – order soon. . . . . In stock on April 30, 2021.

What’s the easiest way to remove a pinion nut?

A large nut secures the pinion gear to the pinion yoke. Using an impact wrench is the easiest way to remove the nut. If you don’t have air tools, you can use a breaker bar and socket to remove it by hand. First, you need to lock the axles from spinning.

What’s the first step in disassembling a Chevy?

The first step is to suspend the chassis and let the rear extend freely under the car. Use the properly rated floor jack to jack up the car and place the correct jackstands under the frame rails. Remove the lug nuts and take off the rear wheels. The shocks are fully extended and can be unbolted.

How to replace 1988-2000 Chevy door hinge pins?

Place your new retainer clips over the bushings and use your small socket or a small hollow piece of tube to hammer the retainer rings in place, ensuring they are fully seated to keep the pins from coming out.

How do you remove the spring from a Chevy truck door?

Remove the door spring behind the hinge — between the hinge and the door itself — by locating the end of the spring and inserting the screwdriver between it and the hinge. Pry, using the door as leverage, until the spring pops out. Spray penetrating oil on the top and bottom of the pins, at the bushings, to make it easier to hammer the pin out.

Where do the bushings go on a Chevy truck door?

For the bottom hinge, the larger bushing goes in the top part of the hinge while the smaller bushing goes in the bottom part of the hinge. In both cases, the head of the hinge bolt goes at the larger of the two bushings. Gently hammer the four bushings into place. Remember that the bushings go in the vehicle part of the hinge, not the door part.

How long does it take to replace door pins on a Chevy S10?

Replacing door hinge pins and bushings on an S10 Chevrolet pickup truck requires a little elbow grease and some know how. The fix takes around two hours to complete. After all is said and done, close your door and listen to the sound of silence.

When do you change the hinges on a Chevy Silverado?

The large doors on GM full-size trucks and SUVs are heavy, and the hinges can eventually wear out. If you can’t close your 1988-2000 Chevrolet Silverado, Suburban or Tahoe or GMC Sierra or Yukon doors without giving them a huge slam and notice that they hang low when open, it’s time to change your door hinges.

Where do the hinge pins go on a Chevy truck?

Remember that the bushings go in the vehicle part of the hinge, not the door part. With the weight of your door still on the jack, work with your assistant to align the hinges and start to slide the hinge pins into place through the bushings — bottom first, then top.

Why are the hinges on my 1988 Chevy Silverado not working?

If you can’t close your 1988-2000 Chevrolet Silverado, Suburban or Tahoe or GMC Sierra or Yukon doors without giving them a huge slam and notice that they hang low when open, it’s time to change your door hinges. The culprit is usually the pins and bushings, which start to allow too much play in your hinges.

How do you replace door pins on a Chevy Silverado?