When did GM replace the ball joint on my truck?
When did GM replace the ball joint on my truck?
My 97 C1500 with 226,000 miles still has its original lower ball joint on the drivers side. Why would all 4 god bad at the same time? The lower ball joint on the passengers side was just replaced a few months ago at 225,000 miles. It to was the original that came on the truck in 1997.
How to replace a lower control arm ball joint?
Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):
What happens when a front ball joint fails?
Should a ball joint break, the wheel becomes totally free to move in any direction, which can damage the car’s fender, tire, and several suspension components, if not more. Usually, when front ball joints start to fail, the vehicle will display a few symptoms that alert the driver a problem has occurred.
How can I check the ball joint on my front suspension?
If your front suspension uses MacPherson struts, look for a wear indicator, which is usually a grease fitting. Grasp the fitting and try to wiggle it. If the fitting moves around inside the housing, you’ll need to replace the ball joint. Jack up the car on the front cross-member.
My 97 C1500 with 226,000 miles still has its original lower ball joint on the drivers side. Why would all 4 god bad at the same time? The lower ball joint on the passengers side was just replaced a few months ago at 225,000 miles. It to was the original that came on the truck in 1997.
Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):
How can I check the ball joint on my front suspension?
If your front suspension uses MacPherson struts, look for a wear indicator, which is usually a grease fitting. Grasp the fitting and try to wiggle it. If the fitting moves around inside the housing, you’ll need to replace the ball joint. Jack up the car on the front cross-member.
What kind of ball joint does a Chevy Equinox have?
Upper ball joint. With premium opt. With performance pkg. With performance suspension. Description: Equinox, Terrain. Description: Without crew cab. All models. 1/2 ton. 2wd, 1/2 ton, std & extended cab. Exc.High Performance Suspension.
How much does it cost to replace a ball joint?
Dealer said lower right is bad but the left should also be replaced. ~ $1300. my 2000 with 169K miles has the same issue. Dealer said lower right is bad but the left should also be replaced. ~ $1300.
How much does a Moog ball joint replacement cost?
Dealer wants over $1600. Now after reading the forums and doing some pricing, I can get MOOG parts for $300 and figure with an alignment, I can be back on the road for under $500. My question is, what am I missing here? MOOG parts are supposed to be quality parts. Is this just shops trying to make money?
How do you know if ball joints need to be replaced?
Inspect the ball joints to make sure they need to be replaced. Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.
What happens when your steering wheel ball joint loosens?
Over time, a car’s ball joints may wear down. If a ball joint starts to loosen, you’ll hear clunking sounds from the front as the joint rattles in the socket. If it tightens up, the steering will bind so you can have a stiff spot as you turn the steering wheel.
How do you put a new ball joint in a car?
Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included.
How to replace lower ball joint on Chevy Silverado?
This video outlines the complete process of removal and replacement of the upper control arm and lower ball joint on a 2008 Chevrolet Silverado 2500 HD 4X4 with torsion bar front suspension. The process is similar on many GM trucks and includes tips and tricks to help make the job easy and do it right. The entire process was unedited for time.
Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):
How do you know if ball joints need to be replaced?
Inspect the ball joints to make sure they need to be replaced. Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.
Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included.
