How to test a GMC ignition control module?

NOTE: Testing the ignition system is a breeze. This tutorial will help you test the ignition coil, ignition module, and the crankshaft position sensor: How To Test The GM Ignition Control Module (1995-2005).

How does the GM distributor mounted ignition module work?

OK, once the fuel injection computer receives the Distributor Reference Hi Signal, it starts activating the fuel injectors and above 400 RPM, starts to send a 5 Volt Bypass Signal to the ignition control module. It’s with the Bypass Signal that the computer starts to retard and advance ignition timing with the IC Signal.

What are the symptoms of a bad ignition module?

The following are usually the most common symptoms of a bad spark plug wires, or a bad distributor cap and rotor on this type of GM distributor mounted ignition control module: The car (or truck, or mini-van, or van) starts and runs, but with a misfire. The check engine light is on. Lack of power.

What was the ignition module on a 1993 GMC k1500?

1993 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a no-start problem caused by the ignition module, or the ignition coil, or the distributor pickup coil. Wiring diagram. Component pin outs.

Where is the trouble code on a GMC?

When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.

What are the codes for GMC check engine lights?

P1245Intake Plenum Switchover Valve P1250Early Fuel Evaporation Heater Circuit P1257Supercharger System Overboost P1258Engine Coolant Overtemperature – Protection Mode Active P1260Last Test Failed SCC Or Theft Detected, Vehicle Immobilized

What was the ignition module for a 1996 GMC k1500?

1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor). Wiring diagrams.

What was the ignition module for a 1996 GMC c2500?

1996 GMC C1500, C2500, C3500 Pick Up. 1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

What kind of ignition system does a GMC Suburban have?

The typical ignition system circuit diagram for the 1992-1995 4.3L, 5.0L, and 5.7L 1500, 2500, 3500 Pick Up and Suburban can be found here: Ignition System Circuit Diagram (1992-1995 Chevy/GMC Pick Up And SUV). Testing the a no-start problem or a misfire due to an ignition system problem is not hard.

What are the wires in the ignition module?

The ignition control module (ICM) has 4 wires coming out of it. Below are the descriptions of what each circuit does. Each circuit is identified by a letter, and this is the same letter that you will find on the ignition module’s connector. Power (12 V) Circuit. Ignition Control (IC) Signal. Engine Ground Circuit. Switching Signal Circuit.

How to repair a GMC Sonoma pick up?

Access our Chevy S10, S15, and GMC Sonoma Pick-Ups 1982-1993 Repair Manual Wiring Diagrams Repair Guide by creating an account or signing into your AutoZone Rewards account. Once you sign in, follow these instructions to access our Repair Guides. Add your vehicle in Manage My Vehicles. Enter your vehicle details.

How to test a GMC ignition control module?