What kind of rear axle does a Mustang II have?
What kind of rear axle does a Mustang II have?
The Mustang II utilizes two different style rear axles. The first axle is used on 4cyl and some 6cyl cars and is a 6 3/4″ ring gear integral carrier axle. The second is used on some 6cyl and all 8cyl cars and is an 8″ ring gear removable carrier axle. The two axles are easy to tell apart.
How big is the ring gear on a Mustang?
Measure the diameter of the ring gear. A 7.5 Ring Gear will measure 7.5. An 8.8 Ring Gear will measure 8.8. You can also count the splines on the Pinion Gear. A 7.5 Pinion will have 28 splines & an 8.8 pinion will have 30 splines.
How big is the carrier axle on a Mustang?
The second is used on some 6cyl and all 8cyl cars and is an 8″ ring gear removable carrier axle. The two axles are easy to tell apart. Looking at the axle from the rear of the car, if the center section has a cover with bolts around the circumference, it is the 6 3/4″ axle. If there are no visible bolts from the rear, it is an 8″ axle.
Where are the wheel bearings located on a Mustang?
Ball bearing assemblies (rear wheel bearings) are pressed onto the outer ends of the axle shafts and set in the outer ends of the axle housing. Certain vehicles are equipped with tapered roller bearings, with which a different type of oil seal is used. These bearings support the semi-floating axle shafts at the outer ends.
The Mustang II utilizes two different style rear axles. The first axle is used on 4cyl and some 6cyl cars and is a 6 3/4″ ring gear integral carrier axle. The second is used on some 6cyl and all 8cyl cars and is an 8″ ring gear removable carrier axle. The two axles are easy to tell apart.
Measure the diameter of the ring gear. A 7.5 Ring Gear will measure 7.5. An 8.8 Ring Gear will measure 8.8. You can also count the splines on the Pinion Gear. A 7.5 Pinion will have 28 splines & an 8.8 pinion will have 30 splines.
The second is used on some 6cyl and all 8cyl cars and is an 8″ ring gear removable carrier axle. The two axles are easy to tell apart. Looking at the axle from the rear of the car, if the center section has a cover with bolts around the circumference, it is the 6 3/4″ axle. If there are no visible bolts from the rear, it is an 8″ axle.
Ball bearing assemblies (rear wheel bearings) are pressed onto the outer ends of the axle shafts and set in the outer ends of the axle housing. Certain vehicles are equipped with tapered roller bearings, with which a different type of oil seal is used. These bearings support the semi-floating axle shafts at the outer ends.
Where do you find the Axle code on a Mustang?
The following axle identification is based on the axle tag located on the axle, if you have the code from the door tag (Certification label) you can look up your axle in our code reference section . The rear axle assembly is an integral-type housing, hypoid design, with the centerline of the pinion set below the centerline of the ring gear.
The following axle identification is based on the axle tag located on the axle, if you have the code from the door tag (Certification label) you can look up your axle in our code reference section . The rear axle assembly is an integral-type housing, hypoid design, with the centerline of the pinion set below the centerline of the ring gear.
How big is the brake drum on a Ford Mustang?
Note: The lengths stated are for a complete axle from brake drum to brake drum. For 64-73 Mustangs subtract 5 inches to get the bare axle housing width. 66-71 Fairlanes, Torinos, Montegos, Comets, and other Ford intermediates with big blocks
What kind of rear end does a Ford Mustang have?
All 1979-1985 Mustangs featured the 7.5 rear end. Starting in 1986 Ford introduced the popular 8.8” rear end in the Mustang. From 1986-2010 the Ford Mustang 8.8 rear end went into all V8 Mustangs (5.0L, 4.6L and 5.4L) and the Ford 7.5” rear end went into all 4 cylinder (2.3L) and V6 Mustangs (3.8L).
How big are the bolts on a Ford Mustang rear axle?
My housing also has the “large” housing ends with 1/2″ bolts at 4 3/16″ spacing. Some modifications I plan adding are a large ‘bung’ for adding oil and to inspect the ring gear through, epoxying a strong magnet in the bottom to catch any metal chips and upgrading the vent to lessen chance of pressure building up and causing an oil leak.
What kind of axle do you need for disc brakes on a Mustang?
If you are looking to upgrade to a disc brake setup from a 94-04 Mustang, you are going to need the SN95 flange axles along with a set of caliper brackets. The SN95 flange axles are hubcentric to allow a perfect fit with the 94+ rotors. A popular swap among Fox Body owners is the 94-98 rear end swap.
How big are the housing brackets on a Mustang?
Elite 4130 Double Hole Lower Housing Brackets. 3-1/2″ axle tube. Welding Required Includes Bolts & Spacers Holes need to be reamed… more info 1979-2004 Mustang 90 Degree lower housing bracket kit is constructed of 3/16 mild steel.
