Other

Is there a priming system on a Duramax Diesel?

Is there a priming system on a Duramax Diesel?

The DuraMax is a 6.6 engine. There is usually not a priming system on a gas engine, because the fuel pumps will usually get it through the smaller filters used quick enough you dont need them. However, if it is a DuraMax engine, then right on top of the fitting where you mount your diesel filter, there is a primer pump and an air bleed valve.

Is the lift pump on a Duramax diesel truck?

Duramax diesel trucks do not have a lift pump. start with the simple things make sure your fuel filter is tight and check the shreader vlave on the fuel rail if that don’t help check the filter housing for a leaks arround the heater element or a crack in the housing itself You can’t post conmments that contain an email address.

Is the Duramax 8.1 diesel engine a gas engine?

Well, one problem is, if its an 8.1, its not a diesel. The 8.1, or Vortec 8100, is a gas engine. The DuraMax is a 6.6 engine. There is usually not a priming system on a gas engine, because the fuel pumps will usually get it through the smaller filters used quick enough you dont need them.

What to do if your Duramax ran out of fuel?

Hereis the location of the bleeder screw, the primmer pump is the round part in the top center and you have to pump it up and down till fuel comes out the vent then claose the vent. kalamykid : Full Size Image Customer : ok

Where is the bleeder screw on a Duramax primer?

ok got it kalamykid : Hereis the location of the bleeder screw, the primmer pump is the round part in the top center and you have to pump it up and down till fuel comes out the vent then claose the vent. kalamykid : Full Size Image Customer : ok kalamykid :

How do you Prime a Duramax Primmer filter?

After the filter is primed, you have to close off the bleeder, and pump the primmer about 15 more times to get fuel to the injectors. kalamykid : the primer should get hard to push.

When did the Duramax 3500 run out of gas?

2015 Duramax (3500) Filled the tank a couple days ago, but Second Opinion] 2015 Duramax (3500) Filled the tank a couple days ago, but the gas gauge never moved off of EMPTY. SO…yesterday it ran out of gas…with a FULL tank!

Why does my GMC Duramax keep losing Prime?

Ran out of diesel on freeway. Put fuel in tank and primed filter in engine compartment. no luck. Have an 04 GMC duramax. Help … read more my 2003 duramax stalls out right after start up. I have to pump the fuel pump on top of the fuel filter to get it to start again then it runs fine. Why? … read more

Why does my fuel pump not prime when I turn it on?

Pulled fuel pump relay and put in a jumper wire to run the fuel pump and it started. Put the fuel pump relay back in and it starts and drives, but the fuel pump still doesn’t prime when turning the key on. I’m afraid that after sitting overnight, it will once again refuse to start.

What to do if your Chevy fuel pump fails?

Chevrolet fuel pump failures are a common and growing problem. If you have a fuel pump harness connector that looks like the flat one on the right or the square one at the bottom, then consider replacing it when replacing the pump. More details about this are below, but you might want to download your Chevy manual to help.

Why is the priming pump on my Duramax not working?

Priming Pump/Filter Housing. Truck won’t start: Chevy Duramax | Performance Boats Forum Priming Pump/Filter Housing. Truck won’t start: Chevy Duramax Did a search and still was not comfortable with the results if found. I was ready to leave for a trip a couple of days ago.

Why does my priming pump not spit fuel?

Click to expand… Verify the oring around the bleed in the filter housing isn’t leaking. After you get liquid out of the bleed, close it and continue to pump it until you can’t compress it. I have pumped that little bastard till my arm almost fell off. It just won’t spit the fuel.

How can I Keep my Duramax Diesel pump healthy?

However, there are measures you can take to keep the pump happy and healthy, the first being to always buy your diesel from a high-traffic, reputable filling station that’s known to dispense good, clean fuel. Second, always change the fuel filter at or before the recommended service interval.

What kind of pump does a Duramax cp4.2 use?

Like all Duramax engines from ’01-’10, the LML was also void of a lift pump from the factory. This means that not only does the CP4.2 have to pressurize fuel as high as 29,000 psi before sending it to the rails, but it also has to pull its low pressure fuel from the tank.

What to do if you lose prime in fuel system?

Dump the factory filter and replace with Nick’s underhood Cat setup. When you order the Cat filter and adapter also order a filter head rebuild kit which replaces the o-rings. Did you find the recommended reading relevant to this discussion?

Where is the primer cylinder on a Duramax Diesel?

On the passenger side of the motor you will find the fuel filter assembly. On top there is a primer cylinder and a plastic bleeder screw. Pump the cylinder until it gets hard, then crack the bleeder and let the air out. Repeat the process until fuel comes out and the truck stays running.

How to fix 2003 Duramax Diesel loosing Prime?

2003 Duramax Diesel loosing prime and will not start until I lift the hood and pump the prime plunger on the fuel filter housing. Clicking this will make more experts see the question and we will remind you when it gets answered. You can’t post conmments that contain an email address.

What do I need to rebuild my Duramax filter?

AutoZone O’Reilly’s Carries the filter head rebuild kit now too part 904-124 for about $25 it says primer seal kit, but comes with all o rings. It will probably have to be ordered but always there next day.

Why does my Duramax not start after running?

Usually they don’t want to start after they have ran for a while when you have injector fuel return issues. That’s why I’m leaning toward something electrical. I have used the crap out of starting fluid. Its usually getting the air out out of injector lines on mechanical injection systems after pump and or injector replacement.

Author Image
Ruth Doyle