How are the fuel lines connected to the carburetor?
How are the fuel lines connected to the carburetor?
If you have 2, small fuel lines to the carburetor connect them and start the engine. Reversing the fuel lines will not prevent the engine from starting. If you have them connected backwards, the engine will start and die. Reverse them and you will be correct. The routing of the fuel lines vary from model to model.
Do you need a fuel line diagram for a craftsman brushwacker?
Jan 25, · Hi Need fuel line diagram for a Craftsman 32CC Brushwacker/Trimmer year serial N model 2pwesotz No one has the routing diagram. Any help would be highly diagramweb.net I have a Craftsman 32cc Brushwacker Trimmer.
Where do the fuel lines connect to on a craftsman 358?
The routing of the fuel lines vary from model to model. Keep in mind that the primer bulb circulates fuel from the tank, through the carburetor, and back into the fuel tank. One line goes from the fuel tank to the carburetor. One line goes from the fuel tank to the primer bulb, from the primer bulb to the carburetor, and back to the fuel tank.
How is a fuel line installed in a trimmer?
The line must be fed into its correct fuel tank hole through the inside of the fuel tank and then pressed firmly into position. To be properly installed, the fuel filter must rest flush with the fuel tank. The next step will help to hold the fuel filter in its correct position.
What do I need for a fuel line?
I need an assembled fuel tank with all fittings and lines or a diagram of how to fit everything together and the required fittings. The parts I ordered are 530069247 fuel line kit, 530069216 vent line kit, and 530014362 fuel pick-up assy (filter).
Jan 25, · Hi Need fuel line diagram for a Craftsman 32CC Brushwacker/Trimmer year serial N model 2pwesotz No one has the routing diagram. Any help would be highly diagramweb.net I have a Craftsman 32cc Brushwacker Trimmer.
Where does the fuel line connect to the tank?
The holes in the tank should be a little smaller than the fuel line so that they seal to the tank without any sealer. On the models that use the barbed connector, the line goes through the tank and the connector is about a 1/2 inch above the tank. The check valve (whoopee cushion part) should attach to the return line inside of the tank.
When to replace the fuel lines on a chainsaw?
Fuel lines schematic Craftsman Chainsaw Model Carb: Walbro WTIt is a good idea to replace the fuel lines if they are no longer flexible, the air filter, and the in tank fuel filter as well. It’s a good idea to replace the primer at this time, too.
What’s the best way to connect a gas line?
You have to install the flare fitting that’s included with the kit. Coat all threaded pipe connections with pipe thread compound before assembly. If necessary, use a bushing to reduce the existing 3/4-inch female pipe thread to 1/2 inch. Use a 90-degree elbow at the stove to avoid kinking the gas tubing when you push the stove against the wall.
Where do gas lines go on a Ryobi?
One line goes from the fuel tank to the carburetor. One line goes from the fuel tank to the primer bulb, from the primer bulb to the carburetor, and back to the fuel tank. Be careful to not put a fuel line too near a hot place on the engine. If the gas is overheated it will vapor lock and stop fuel flow.
What to do if flare on gas line does not match?
If the flare fitting on the flexible stainless gas line matches the size of the flare fitting on the existing gas valve, you can simply screw it on. If the fittings don’t match, one solution is to replace the valve with one that has a flare fitting on one side and a 1/2-inch female pipe thread on the other side.
How do you draw a fuel line diagram?
Draw a diagram of where the fuel lines connect (or take a digital photo). Be sure to note on the drawing which is the small and which is the large line. Remove the fuel line from the carburetor with the hemostat forceps or long needle-nosed pliers. Grasp the old fuel line inside of the tank and pull it into the tank and out the filler opening.
If you have 2, small fuel lines to the carburetor connect them and start the engine. Reversing the fuel lines will not prevent the engine from starting. If you have them connected backwards, the engine will start and die. Reverse them and you will be correct. The routing of the fuel lines vary from model to model.
What to use to test gas line connection?
Turn the gas back on and swab each joint with a solution of 2 tsp. dishwashing liquid to 1 cup water or with a commercially prepared leak testing solution. Coat each connection and watch for bubbles to form.
One line goes from the fuel tank to the carburetor. One line goes from the fuel tank to the primer bulb, from the primer bulb to the carburetor, and back to the fuel tank. Be careful to not put a fuel line too near a hot place on the engine. If the gas is overheated it will vapor lock and stop fuel flow.
