How to replace rear disc brakes in a Ford Focus?
How to replace rear disc brakes in a Ford Focus?
Lay the caliper over the top of the brake pads and secure the bolts using a torque wrench. Tighten the bolts to 26 ft. lb. Fasten the brake cable to the brake caliper. Replace the wheels and lower the Focus to the ground. Bleed the brakes if necessary.
How do you replace the rear drum brake?
6) Remove the retaining clips by simply using a screwdriver and push down on them. 7) You can then wiggle, pull and push to get the assembly of the rear brakes off the backing plate. 8) Remove the parking brake cable from the brake assembly. Take the brake pads and springs apart, replace with new brake pads.
How to replace rear brake shoes and wheel cylinder?
How to replace the rear brake shoes and a leaky wheel cylinder on a 1999-2005 Ford Focus. You must torque the drum bearing to 170 foot pounds of torque which is not shown in this video. — Please use needle noise vise grips instead of side cutters on the brake springs. —
How do you replace brake pads on a car?
8) Remove the parking brake cable from the brake assembly. Take the brake pads and springs apart, replace with new brake pads. 9) Proceed to clean the backing plate with the brake clean, then wipe the rub points dry. 10) Apply the silicone lube or whatever you choose to use.
Lay the caliper over the top of the brake pads and secure the bolts using a torque wrench. Tighten the bolts to 26 ft. lb. Fasten the brake cable to the brake caliper. Replace the wheels and lower the Focus to the ground. Bleed the brakes if necessary.
Where to change brake fluid in Ford Focus?
Before you turn back the piston, move to the right rear area of the engine bay and twist off the brake fluid reservoir cap in the counter clockwise direction. Removing the brake fluid reservoir cap will allow the fluid to more easily travel backwards through the lines when you turn back the piston. Turn Back Caliper Piston Replace Brake Fluid Cap
What do you need to replace rear disc brakes?
The tools you need are Rear Caliper Piston Adjuster 206-010 and Adapter 206-026. After you get the tools, read further to learn how to replace your rear disc brakes. Lift the Focus off the ground with a car jack and secure it on all sides to prevent it from falling over. Loosen the lug nuts with a torque wrench and remove the wheels.
How do you replace the rear brake caliper?
You will need the Rear Caliper Piston Adjuster 206-010 and Adapter 206-026. Replace the brake pads with the new ones. Lay the caliper over the top of the brake pads and secure the bolts using a torque wrench.
Before you turn back the piston, move to the right rear area of the engine bay and twist off the brake fluid reservoir cap in the counter clockwise direction. Removing the brake fluid reservoir cap will allow the fluid to more easily travel backwards through the lines when you turn back the piston. Turn Back Caliper Piston Replace Brake Fluid Cap
How to replace rear brake caliper in Ford Focus?
Replace the metal spring clip on the outer face of the the rear brake caliper. Replace the rear wheel and spin on the five lug nuts. Slightly tighten the 5 lug nuts in a criss-cross or “star” pattern. Lower the vehicle from the jack stands using the floor jack until the rear wheel holds enough weight to keep it from spinning.
How do you retract a brake piston on a Ford Focus?
Retract the brake piston using the special tools purchased from the Ford dealership. You will need the Rear Caliper Piston Adjuster 206-010 and Adapter 206-026. Replace the brake pads with the new ones. Lay the caliper over the top of the brake pads and secure the bolts using a torque wrench. Tighten the bolts to 26 ft. lb.
What kind of brake pads do I need for my Ford Focus?
Owners of other similar Ford sedan or hatchback vehicles such as the Fusion, Fiesta, Taurus, C-Max, and Taurus may also find these DIY rear brake job instructions to be helpful.
What causes the brake caliper on a Ford Focus to stick?
Your Ford Focus’s braking system is the most important safety feature on the vehicle. If it does not work properly, it can put you in a situation where you can be injured or killed. There are quite a few different situations that can cause a caliper to stick.
The tools you need are Rear Caliper Piston Adjuster 206-010 and Adapter 206-026. After you get the tools, read further to learn how to replace your rear disc brakes. Lift the Focus off the ground with a car jack and secure it on all sides to prevent it from falling over. Loosen the lug nuts with a torque wrench and remove the wheels.
You will need the Rear Caliper Piston Adjuster 206-010 and Adapter 206-026. Replace the brake pads with the new ones. Lay the caliper over the top of the brake pads and secure the bolts using a torque wrench.
