How do I program my new Ford Focus Key?

How to program a spare key for a Ford Focus

1. Place one of the original keys in the igniton. Turn the key from off to run and back to off.
2. Place the second original key in the ignition. Turn the key from off to run and back to off.
3. Now, place your new key in the ignition. Turn the key from off to run and back to off.

How long does it take to get a new key from Ford?

A: Generally speaking, for a new Ford key or fob, the process should take between one hour to two, depends on the year make and model of the car. If codes are available, this process is even faster.

Do you need to program a Ford Focus key?

Ford Focus has different types of keys. Some require programming and some don’t. All transponder chip keys and/or smart key fobs need to be programmed with a special programming machine that only an automotive locksmith or the dealer has. There is no need to program non-transponder metal keys.

Do you need a transponder for a Ford Focus?

Keys that needs to be programmed and you will need an automotive locksmith or the dealer (Transponder or remote keys) Ford Focus Non-transponder keys are metal keys that have no chip in them and therefore no programming is needed: None – this model has only the keys that should be programmed.

How much does it cost to replace a Ford Focus key?

A: In short, to replace a Ford Focus key usually costs between $80-$400. It depends on a few factors: Type of key. The year manufactured. Time of day & your location. Where you get a key replacement (Dealer, automotive locksmith, online, etc.) Availability of code to cut a new key. Original ignition or not.

How long does it take to program a new Ford key?

Within three minutes, turn the ignition cylinder into “OFF” position and then back to “ON” again. The security light on the dash should flash for an additional 15 minutes and then go off. Once the security light goes off after the 3 rd time (total 45 minutes) the new key should be programmed and start the car.

Ford Focus has different types of keys. Some require programming and some don’t. All transponder chip keys and/or smart key fobs need to be programmed with a special programming machine that only an automotive locksmith or the dealer has. There is no need to program non-transponder metal keys.

How often do you change the key fob on a Ford Focus?

Ford Focus key fob is battery operated. Every two years or so, or when the battery is low, you may need to change the key fob battery. Here is all the information you need. The type of battery you need is a CR-2032.

Keys that needs to be programmed and you will need an automotive locksmith or the dealer (Transponder or remote keys) Ford Focus Non-transponder keys are metal keys that have no chip in them and therefore no programming is needed: None – this model has only the keys that should be programmed.

How long does it take to program a Ford key fob?

Therefore, we highly recommend having at least two new cut keys and program them both. Coding machine for Ford transponder keys and key fobs used by an automotive locksmith B. Programming Ford keys require about 50 minutes of battery life, without the car being on.

How do I program my new Ford Focus key?

Ford Key Fob Programming Instructions

1. Close all doors on your vehicle.
2. Turn the ignition from OFF to RUN 8 times, within 10 seconds.
3. At this point, the door locks will lock and unlock.
4. Within 8 seconds, push any button on your Ford remote to begin programming.

How do you program a new Ford key?

Once you have a replacement key, the steps you need to take to get it fully programmed are very simple and easy to understand. 1. First you need to open the door and put the vehicle key in the ignition. 2. Next you need to turn the key clockwise from the “off” position to the “on” position.

What kind of key do I need for my Ford Focus?

Ford Focus has none of this key type – all Ford Focus keys have a chip and need to be programmed. These keys, also known as remote smart keys, intelligent keys or key fobs, and transponder keys, have a security chip. Programming is needed. Also, a special machine is needed to program them. An automotive locksmith or dealer should do it for you.

How do I program a new Pat key?

Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes. 4.After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car.

When to add a new key to forscan?

Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below). If you want to add a key….

Once you have a replacement key, the steps you need to take to get it fully programmed are very simple and easy to understand. 1. First you need to open the door and put the vehicle key in the ignition. 2. Next you need to turn the key clockwise from the “off” position to the “on” position.

How long does it take for forscan to program a new key?

There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program.

How to relearn Ford Pats control function module?

Enter “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Cycle key to OFF and then RUN. 2 keys required. Cycle key 1 to RUN. Enter Security Access on the PATS control function module. Select “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Cycle key 1 to OFF, then RUN, and back to OFF.

Do you need to program two new keys?

Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below). If you want to add a key….