What causes a Chevy truck to turn over but not start?

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

What does it mean when your car says no crank?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. The most common problem, that causes this condition is a failed starter motor.

What’s the difference between no start and no crank?

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

What does it mean when your car won’t turn over?

When your car won’t crank, won’t turn over, won’t start, and talks back with a single click or rapid-fire click, click, click, click, click, it’s likely the result of an issue with the electrical charging system and/or the starter. These symptoms could spell problems with the wire connections, battery, battery terminals, or alternator.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why is my GMC Sierra 1500 stalling out?

No change. Next, read somewhere that bad ground wire on Thermostat housing can cause ECM issues. Checked it, cleaned it off, verfied that contact wanhers are all steel and attract a magnet, reinstall the ground wire.

What happens when you reset the ECM on a 1992 Chevy truck?

Make sure the scan tool you decide on works with 1992 General Motors software. Failure to fix the problem before resetting the ECM will cause the Check Engine light to illuminate again, and may cause issues with the ECM’s ability to diagnose future problems.

Why is my Chevy 4.3 engine still running?

Checking your vehicle’s fluid levels is always a good idea to maintain the overall longevity of the engine. Once you have ruled out all the basics, you can go back to what the Chevy 4.3 engine is known for: bad idle air control valves and throttle control switches.

What kind of noise does a Chevy 4.3 make?

by Contributor. A common complaint with the Chevy 4.3 engine is that it doesn’t idle well, it’s loud and makes awkward noises. Examples of this are staling, lurching and poor acceleration. Poor idling and loud engines usually go hand-in-hand.

What to do if your GMC Sierra stall out?

69 people found this helpful. I have a 98 gmc searria 4×4 i checked fuel pressure it was under i changed fuel pump and fuel filter and its still starving for fuel what to do it starts with starting fluid 42 people found this helpful.

What should I do if my Chevy Silverado wont start?

You should always have a suitable jumper cable in the trunk. With its help, the battery receives a current pulse from another vehicle that is sufficient to start the vehicle. The battery can then recover and recharge while the engine is running. Another option is to connect a battery charger.

Why does my Chevy Spark Plug not start?

Chevrolets have a common issue with fuel filters getting clogged. You always want to replace the fuel filter when replacing the fuel pump. This could cause the concern you are having. It may seem as you are getting enough fuel from the pressure regulator but if the pressure from the fuel tank is not correct, it will still not start.

Why does my fuel pump not start when I change it?

You always want to replace the fuel filter when replacing the fuel pump. This could cause the concern you are having. It may seem as you are getting enough fuel from the pressure regulator but if the pressure from the fuel tank is not correct, it will still not start. Another problem you could be having is spark.

What causes a Chevy Silverado to run rough?

If an oxygen sensor goes bad, it can make your Silverado run too lean (or rich). A super lean running engine will often idle rough. Fuel Injectors. The fuel injection systems job is to atomize the fuel into fine mist.

Why does my car not start when I start it?

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

Where does the fuse come from on a 1992 Chevy truck?

The purple wire at the starter solenoid, should be hot with the key in the crank position. My info shows more than one circuit at the starter S terminal, feed for the crank fuse, comes from the S terminal by way of the ignition switch, in crank position.

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

How to troubleshoot your TBI fuel injection system?

Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad. See

What causes a car to have a no start condition?

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no-start conditions. Blown head gasket. Blown engine. 4.)

What is the TBI code on a 1990 Chevy truck?

Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.

Connect a 30-amp fused jumper between the battery positive voltage circuit of the starter relay switch circuit and the supply voltage circuit of the starter solenoid. Does the engine crank?

Why is my Chevy Silverado not cranking over?

Since you have voltage on the crank fuse while in crank position, we know the ignition switch is good. The pcm supplies the ground to the starter relay to turn on the starter. It is possible if the wiring is good, there is a problem with the pcm.

Why does my starter turn without turning the engine?

Starter Turns Without Turning the Engine. A starter that spins without turning the engine is caused by the starter gear failing to engage the engine’s flywheel. This usually indicates that the starter pinion is sticking and not allowing its gear to move into position with the flywheel.

Why does my Chevy Silverado have no spark?

Common causes for no spark are a weak battery, indicated by a slow-turning starter, a faulty ignition coil or a wet ignition system. Less common problems are faulty sparkplugs, broken or disconnected coil wires or broken wires in the ignition system.

Why does my Chevy Silverado not start when hot?

A clogged fuel filter, dirty fuel injectors or weak fuel pump can result in too little fuel reaching the cylinder, causing poor fuel ignition and the need to depress the accelerator to assist starting. An engine that is difficult to start when hot can be caused by a clogged air filter restricting airflow to the intake.

Why does my car not start when I Turn on the ignition?

The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter). However, the source may also be a mechanical fault (for example, a leaking valve), or faulty components in other systems.

Where is the pulse on a Chevy truck?

Engine cranking, the negative/tach side of coil, should have a pulse, if no pulse, check the pick-up coil or ignition module. helpful?

What should I do if my Chevy Silverado starts acting up?

Contact GM if a relatively new Silverado starts acting up. It could be that there is a TSB (technical service bulletin) or recall that addresses the problem. If so, give your dealer the TSB number and expect to get your repair made for free. Since 2007, the newly designed Silverado shares the same platform with the Chevy Tahoe and GMC Yukon.

Where to come when your 6.5L diesel will not start?

Where to come when your 6.5L Diesel will not start! “The PMD / FSD (Pump mounted driver) is by far the #1 cause of 6.5L no-starts (at least 90%). If your truck experienced random stalling like someone shut the key off before ultimately refusing to start again, the PMD is very likely the issue.

Why are GM diesel engines a ticking time bomb?

GM promised consumers the continued reliability of their diesel engines, but with increased fuel efficiency and power at greater fuel efficiency. However, this came with a hidden and catastrophic cost that was secretly passed on to consumers,” the suit claimed while also referring to the engines as a “ticking time bomb.”

Is there no fuel from injectors to start truck?

No fuel from injectors to start truck. When I try and start my 93 Chevy Cheyenne k3500 no fuel come out of the injectors. If I use starting fluid the truck starts and the injectors work great. Has died a couple times while driving, but mostly runs fine and then won’t start one turned off.

What should the fuel pressure be on a Chevy Cheyenne?

93 Chevy Cheyenne k3500, if it is running the Chevy vortec engine the fuel pump pressure is way too low, should be 56 psi+ depending on CSFI/CPI system or it will not start or open injectors, with out the aid of starting fluid. The factory manual specifies that the fuel pressure for the CSFI system should be between 56-62 PSI.

Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

What causes a car to act like it has a bad starter?

Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one.

Can a bad battery cause a car to not start?

Sometimes your car starts, sometimes it doesn’t. Intermittent operation can be a sign of a failing starter solenoid. Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one.

What to do if your Chevy truck won’t start?

Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse. have the same problem? Hi, thanks for the donation.

Can a blown fuse cause a starter to not start?

Blown fuse – Sometimes the simplest explanation is the best one. A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.

Why does my GM Truck start and die?

Starts and runs fine and then all of the sudden. Yesterday morning it starts and dies after about 1 second, started it again and same results. It does this several times. After about 30 mins of trying and talking to it a while it started and ran fine. Drove over to the garage turned it off and restarted several times and it was fine.

What kind of truck starts and then dies?

99 Z-71 with a 350 5.7. Starts and runs fine and then all of the sudden. Yesterday morning it starts and dies after about 1 second, started it again and same results. It does this several times. After about 30 mins of trying and talking to it a while it started and ran fine.

Why does my Chevy Suburban stall all the time?

One of the most common issues your Chevy Suburban is likely to develop is a stalling problem. The most challenging part of diagnosing a stalling problem is reproducing the conditions that led to the stall in the first place. Stalls can happen at any time, and it can be incredibly jarring when it does happen.

Why does my Audi A4 stall when I push the gas?

The first is that by limiting the amount of torque when you push the gas pedal for a second or two, engine life is increased by reducing the stress on it during takeoff. The second is improved fuel economy. Here’s a great article on diagnosing a bad throttle position sensor from cars direct.

What kind of truck is a 1994 Chevy?

My fiancé’ bought a 1994 Chevy 3/4 ton 4×4, 5.7L, V8. the throttle body is dumping fuel into the motor. He changed the plugs, wires, distributor, cap, rotor, fuel1 filter, and computer. He checked the timing and it’s good.

Why is my Chevy Vortec 4300 V6 leaking fuel?

In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.

Are there any problems with the Chevy 4.3 Vortec engine?

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

Why does my Chevy C / K 1500 not start?

FYI – If the pass lock isn’t working properly, the computer will not keep the fuel pump on when the key is turned to start and released. 72 people found this helpful. Note: If the battery dies or is disconnected, or the computer is disconnected, this procedure may have to be repeated.

Why does my 96 Chevy Express van not start?

Also had a similar issue spin and no start with a 96 Chevy Express Van with the 5.7L. This vehicles issue turned out to be a shorted pink wire in the wiring harness that runs up the passenger side of the block. The vehicle had died while driving several times and wouldn’t start. Then, finally after blowing a couple fuses, would start at all.

What should I do if my Chevy Colorado wont start?

When this happens, it cranks but won’t turn over. The battery is fine. If I wait 20 min to several hours, it will finally start & seem perfectly normal. The one thing it won’t do, is repeat this for the mechanic at the dealership!

What does intermittent no start mean on a car?

Share it! An intermittent no-start condition references any time where starting is possible sometimes, and other times the engine will not start. This implies that the difference between starting and failure to start is not understood.

Is there a problem with my Chevy Silverado?

Will turn key and it is like no power from battery to starter, but have lights, radio, etc. Turn key again or sometimes multiple times, to no avail. Then, turn it one more time and it starts. Then the next 15 starts, no problem. Sometimes hot engine, sometimes cold. UPDATE: 2-6-14; I sold the truck to my father. He changed the starter.

Why is my fuel pump not producing pressure?

The fuel pump is able to create pressure using electricity but if it is not getting the adequate voltage of electricity it will not be able to function properly. Consequently, the fuel will not be released at the perfect pressure and your car will lose efficiency.

Why does my 1997 Chevy c1500 not start?

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start. I changed the fuel filter and fuel pump relay.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Why does my fuel pump not turn on?

Well getting to start by adding fuel to the throttle body is not going to turn on some special switch that will send a signal to the pump and injectors. I’m sure you probably just have a bad fuel pump that doesn’t have enough pressure or volume to start the truck, but at running speed can keep up.

Why does my 1994 Chevy S-10 not start?

1994 Chevrolet S-10 4.3 tbi. I never get the signal to turn on the fuel pump or fire the injectors but if i poor gas in the intake once the truck starts it runs fine. Any ideas ? I have replaced the fuel pump relay oil pressure switch and computer.

How to test for fuel spray during crank?

This is to be an ignition 1 (ING1) source which is power in both the key run and crank position. Correct the connection of this wire and verify voltage to the pink wire on the injector connector. Test again for fuel spray during crank. If the engine still cranks, is spraying fuel, but will not start go to step 2.

How can I tell if my truck is not starting?

A test for DC voltage between a ground point (eg. battery negative terminal or the engine block) and the large wire on the starter can diagnose a blown fuse (it will read 0V) but it can’t be used to indicate if the connection or starter are ok.

What causes a car to not start up?

The cause of this problem is usually one of 3 things – a failed starter motor, a bad connection between the battery and starter motor, or a blown fuse (if present) in line between the starter and the battery.

Why does my 350 Chevy truck not start?

350 chevy truck cranks but won’t start – Maintenance/Repairs – Car Talk Community Truck ran fine with no indication of problem. When outside temp. dropped in teens one morning it wouldn’t start.

When did Chevy stop using the 350 engine?

Get the facts on the history and specifications of the Chevy 350 engine, finding replacements parts, and finding Chevy 350 crate engines for sale. Beginning in 1985, Corvettes featured a fuel-injected version of the Chevy 350 engine; other passenger cars equipped with the 350 engine continued to use a four-barrel carburetor.

How much torque does a Chevy 350 have?

Rated at up to 380 pound-feet of torque, this engine is great for towing; however, fuel economy is low and — depending on the compression ratio — it might require premium fuel.

Is there a problem with the Chevy Vortec engine?

3L [&Vortec&] engine, the LU3, which was manufactured from 2003-2014 has been known to [&consume&] excessive amounts of [&oil&]. Owners [&have&] reported the car requiring [&two&] quarts or more of [&oil&] in between normal [&oil&] changes. The excessive [&oil&] [&consumption&] is likely to be caused by the Active Fuel Management system.

What to do if your Vortec won’t start?

96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark. Hey everyone, I have a 1996 Chevy C1500 with a 5.7L Vortec, I got the truck recently and was told it just needed a Fuel pump, I replaced the Fuel pump, and the Filter, also the pump turns on and there is fuel up at the rail, I pushed the pin and it shot right out.

What causes a Chevy truck to turn over but not start?