How to set up a Ford upfitter switch?

4th, wire the positive lead from your lights to the pass thru wire at the firewall and ground the other. should be good to go… Mine was a little more complicated, but if you have a pair of 35W or 55W lights this will cover you, use one of the 30amp switches, your owners manual will tell you wich color it is.

Where are the auxiliary upfitter switch wires located?

The auxiliary upfitter switch wires aren’t typically the wires you will clearly see right bellow the driver side steering column. You can typically find the wires and the relays under the plastic cover, located on the end of the driver side dash.

How to wire your light bar to your Ford auxiliary switches?

Installing a Black Oak LED light bar or LED POD in later model Ford F-Series Super Duty Trucks with auxiliary Upfitter switches is a breeze. There are three Ford Fleet bulletins covering the details of Ford Upfitter switches for various model years:

Where is the auxiliary wiring on a Ford F-Series?

If you need more room to work, you can unclip the relay pack and pull it out under the driver steering column right near the parking brake. You can also then gain access to the wiring off the back of each auxiliary relay. Hope this helps!

Where are the auxiliary switches on a Ford F-Series?

For those that have a 2007+ Ford F-series you’ve probably always noticed the switches to the left of the steering wheel that seem to not control anything. Those are the Ford up fitter switches that were designed to allow for auxiliary control.

Where are the factory switches on a Ford F-150?

If you are looking to use the factory upfitter switches in a Ford F-Series Super Duty Truck (F-150, F250, F350, F450, F550) then this tip may be helpful to you. The 4 factory switches are typically located on the lower passenger side of the dash, below the stereo.

You should be able to located the fuses for the auxiliary switches in the fuse panel to identify the max current for each switch. I believe AUX 1-2 are 30 Amps, and AUX 3-4 are 10 Amps. If you need more room to work, you can unclip the relay pack and pull it out under the driver steering column right near the parking brake.

How many amps are in a Ford Upfit switch?

To help power your upfit needs, Ford has increased the circuit capacity over the previous generation. There are now four 25 amp circuits. Plus two 40 amp circuits which can be configured to be hot at all times. So you don’t need to have the vehicle running for power.

Where are the Upfitter switches located on a Ford Super Duty?

In addition to the upfitter switch blunt cut wires, this bundle contains the following blunt cut circuits: All relays and fuses are located in the upfitter relay box. NOTE: Upfitter Switches cannot be added to a vehicle that was not built with this option at production.

Can a Ford light bar be used as an auxiliary switch?

Those are the Ford up fitter switches that were designed to allow for auxiliary control. Installing a Black Oak LED light bar or LED POD in later model Ford F-Series Super Duty Trucks with auxiliary Upfitter switches is a breeze. There are three Ford Fleet bulletins covering the details of Ford Upfitter switches for various model years:

Can a upfitter switch be added to a car?

NOTE: Upfitter Switches cannot be added to a vehicle that was not built with this option at production. Figure 2: Upfitter Relay Box and upfitter switch blunt cut output location.

How to splice an upfitter wire to a pass thru wire?

3rd thing, splice an upfitter wire to a pass thru wire, I used a short piece of wire between the two, but if you have really skinny arms and can stand on your head for extended periods you may be able to get the two together… all the colors and such are listed in the owners manual.

What does the upfitter interface module ( UIM ) do?

The UPFITTER INTERFACE MODULE (UIM) is an electronic control module that has the ability to operate equipment (such as lift buckets, cranes, motors, salt spreaders, snow plows, etc) with external automotive grade relays via customer programmable logic based on switch inputs and CAN signals. The operation of such equipment

How to wire a standard single pole light switch?

How to Wire a Standard Single Pole Light Switch A standard single pole light switch will simply require you to attach the black (load) wire into it, and then the black wire leaving the switch and to your lights. The switch serves to cut the power from reaching the light switch.

What’s the best way to wire a light switch?

The wire strippers should have a spot marked for each gauge wire. Next, bend the wire into a pig tail loop so that you can easily attach to the screws on the light switch. Your switch may have slots to push the wires straight into place rather than use the screws on the side.

How to install Help upfitter switch wiring for Ford tremor?

Switches five and six are rated for 40 amps, so I used single pin connectors rated to handle the heavier loads on switches five and six. These connectors make for a very clean install and if service is needed, just unplug the connectors instead of cutting wires. The answer to all of your most demanding power application requirements.

What are the different colors of Ford Upfitter switches?

There are three Ford Fleet bulletins covering the details of Ford Upfitter switches for various model years: Refer to these bulletins to determine the location of the Aux switch wires, insulation colors and amperage capacities of each switch. For example, model year 2008 Aux 1 and Aux 2 30A switches are yellow and green/brown, respectively.

What kind of aux switch does Black Oak light bar use?

Aux 3 is violet/green with a 10A rating and Aux 4 is brown with a 15A rating. Thus, the Black Oak Curved 50 inch light bar can use Aux 1 or Aux 2 switches, whereas the 20 inch light bar with double rows of 5W LEDs would connect to Aux 3 or Aux 4 switches.

How to set up a Ford upfitter switch?