How is the timing on a Ford 460?

I am timing it with the vacuum disconnected from the distributor and hose plugged. Hose is connected to the port on the carb. This is a basic engine, no emissions left, maybe 3 vacuum hoses. I’d have to go count but you get the idea. Engine ran well before the pickup coil went bad.

How to maximise power on a Ford 460?

Gonna start a sticky with tips and tricks to maximising power in the 73-86 460. 1. Timing set change; 72 and up have an 8* retard in the timing set stock. Install a 69-71 timing chain set (double roller is also a good upgrade). 2. Carb change; throw that 650 in the scrap pile and install a properly tuned list# 3310 carb 3.

What should I do if my 460 won’t start?

But if its been sitting there a little bit (LONGER THAN ABOUT 5-10 MINUTES) it will blow out what smells like RAWL gas when it fires up. So im lost as to what its doing.But i can tell you it did it before the MSD ignition so im thinking i need a carb spacer made of plastic to insulate the carb is the only thing i can think of.

How does vacuum advance work on Ford 460?

Initial plus mechanical. Vacuum advance is at part throttle to increase response and economy and does not count toward total timing as noted above. Watch the distance between the reluctor tooth and pick up to see if it changes as you apply vacuum to the dashpot. Check the coil resistance at rest and at full advance to see if it changes.

What should the tming be on a Ford 460?

Tming; (A) replace a points distributor with a Duraspark unit that is recurved with a proper timing curve, (B) Set timing at 12* initial. 5. Both Crane and Harland Sharp offer roller rocker conversions; this is a great addition.

What’s the difference between the Ford F350 and F450?

There is little difference between the two vehicles when you look at their dimensions but that little difference may be very important if you are a little taller than average. First, the F350 is 250 inches long and roughly 106 inches wide. Its height measures out at 81.3 inches and the wheelbases reaches 159.8 inches long.

What kind of engine does a Ford F350 have?

Two engines are available. The F350 gets the 6.2L 2 valve V8 FFV on almost all models except for the F350 Limited/ This engine produces about 385 hp with about 430-pound foot of torque. The F450 gets the 6.7L power stroke V8 turbo diesel motor that comes with 450 hp and over 900-foot pound of torque.

What’s the turning radius on a Ford F350?

The Super Duty model comes with a regular and extended cab model. The first one offers you about 47.7 feet turning radius. The extended cab is a bit higher due to its extended length. The turning radius on that model is 49.1 feet.

Can a Ford 460 be a 472 engine?

If you are looking to over-bore a 460 then it can easily handle a 0.060 increase which would make it a 472. The OEM heads on a 460 are a bit of a mixed bag when it comes to performance. The intake side of the head provides a cross-sectional oval port which helped give the engine the high torque ratings that it was known for.

What’s the stroke length of a Ford 460?

A stock 460 cylinder bore was measured at 4.36 inches and had a 3.85 inch stroke with a rod length of 6.605 inches which would create a nice rod length to stroke ratio of 1.71:1. If you are looking to over-bore a 460 then it can easily handle a 0.060 increase which would make it a 472.

Where was the Ford 460 V8 engine made?

Beginning in 1968, the Ford 460 was manufactured at Ford’s plant in Lima, Ohio. A stock 460 cylinder bore was measured at 4.36 inches and had a 3.85 inch stroke with a rod length of 6.605 inches which would create a nice rod length to stroke ratio of 1.71:1.

What is the timing number on a Ford distributor?

The reluctor arm on a Ford has two slotted sides, only one side contributes to the timing, the arm can be flipped around if more advance is needed (see pictures.) On Fords each side is stamped with a number, usually 10L and 13L; or some have 15L and 18L.

What kind of air intake does a Ford 460 need?

A 3″ SINGLE is not free flowing enough. If going the single route get the diesel 4″ or even aftermarket 5″ system. EDIT: A good FRESH AIR intake system is next. There is one thing you can do right now and it won’t cost you a dime.

Is the Lincoln 460 a good pickup truck?

I have a 76/77 lincoln 460 in my 79 truck. I’m having issues with getting it timed. This started when I had to replace the pickup coil in the distributor. With the vacuum advance disconnected it runs pretty decent.

How much fuel does a Ford F250 460 use?

On to an example; My completly stock 4.6 super crew pulling 12,000 gross combined weight got 9 to 10 mpg over 230 miles round trip to the race track. Your motor displacment is 1.75 times larger and will take more fuel just on engine size alone besides the weight of your truck is likely higher.

Can a Ford 460 be swapped for a 429?

Swapping a 460/429 into your 79 and older Ford can be really easy or really hard depending on your parts availability and your specific truck. Ford only offered 460s in 2wd trucks from 73-79 a 460 never came in a 4wd or in a truck with a 4spd.

Can a Ford truck have a 460 motor?

They can come from a Ford Van that had a 460 or a 2wd Ford truck with a 460. They also can come from an 80-up Ford truck that had a 460 motor. If you are using a car motor the driver’s side exhaust manifold is the same as a truck the passenger side car manifold does not fit and requires cutting the frame which then leads to a broken frame.

What was the fuel milage on a 1996 Ford F250?

1996 F250 Crew cab, short bed, 4×4 with the 460 and E4OD trans. I have put the full banks kit. (headers, y pipe, muffler and tailpipe). K&N air filter, flex a lite electric fans. First time out of the shop the truck made 17.6 miles per gallon. After a few trips the milage strated to drop. 15 then 12 then 9. Put in a new O2 sensor same thing.

How do you set ignition timing on a 1995 Ford F-350?

Start the engine and observe the timing marks. Loosen the distributor clamp bolt and rotate the distributor until the marks are aligned. Tighten the clamp bolt and verify that the timing is set correctly. Replace the computer connector. Insert your key into the ignition of your 1995 Ford F-350 and start the engine.

Where is the timing mark on a Ford?

Locate the timing mark notch on the harmonic balancer. If the mark is not visible “bump” the engine over by turning the ignition key to engage the starter then immediately releasing it (do not allow the engine to start). Observe the balancer each time. Once the mark is visible, chalk or paint a line around it.

Where is the vacuum hose on a Ford 460?

Hose is connected to the port on the carb. This is a basic engine, no emissions left, maybe 3 vacuum hoses. I’d have to go count but you get the idea. Engine ran well before the pickup coil went bad. I can drive it now with no distributor advance connected but mileage sucks. What is your initial timing set to? What is your total timing?

How do you change the ignition timing on a vacuum advance?

Start the engine and aim the timing light at the timing marks on the engine crankshaft pulley. Adjust the timing by using the above procedures until the correct timing is achieved, then unplug the rubber hose and push it back onto the vacuum advance.

What kind of timing set do I need for a Ford 460?

Timing set change; 72 and up have an 8* retard in the timing set stock. Install a 69-71 timing chain set (double roller is also a good upgrade). 2.

When to increase power above stock in a Ford?

1. increase power above stock ONLY if it can be done without decreasing stock gas mileage and without making engine more unreliable or rough running or rough idling or harder to start or hesitating on acceleration or costing huge $.

Can a Ford OBS install a timing chain?

Ford OBS; Kevin’s 460 F350 Timing Chain Install! – YouTube Ford OBS; Kevin’s 460 F350 Timing Chain Install! If playback doesn’t begin shortly, try restarting your device.

What should the timing be on a smog engine?

Iron headed smog engines typically like 34 to 36 degrees total timing. Initial plus mechanical. Vacuum advance is at part throttle to increase response and economy and does not count toward total timing as noted above. Watch the distance between the reluctor tooth and pick up to see if it changes as you apply vacuum to the dashpot.

Ford OBS; Kevin’s 460 F350 Timing Chain Install! – YouTube Ford OBS; Kevin’s 460 F350 Timing Chain Install! If playback doesn’t begin shortly, try restarting your device.

How do you put timing chain on sprocket?

(If you are using a multi-indexed sprocket like the one on the left, be sure that the slot marked zero is the one you are aligning with the key on the crankshaft.) Place the timing chain onto the cam gear and then over the crankshaft gear as you slide the lower gear over the keyway and into place.

How to install timining chain and gears in your big block Ford engine?

Smooth the snout of the crank with emery cloth and run a tap down the threads before installing the crankshaft gear. This will ensure smooth assembly and an accurate torque reading. This Tech Tip is From the Full Book, HOW TO REBUILD BIG-BLOCK FORD ENGINES.

How do you change distributor on 1995 Ford F-350?

Loosen the distributor clamp bolt and rotate the distributor until the marks are aligned. Tighten the clamp bolt and verify that the timing is set correctly. Replace the computer connector. Insert your key into the ignition of your 1995 Ford F-350 and start the engine. Turn off all accessories, including the radio and air conditioner/heater.

Why is vacuum advance not counted in total timing?

Vacuum advance is at part throttle to increase response and economy and does not count toward total timing as noted above. Watch the distance between the reluctor tooth and pick up to see if it changes as you apply vacuum to the dashpot. Check the coil resistance at rest and at full advance to see if it changes. Wire issue, defecting PU coil etc.

How is the timing on a Ford 460?