What are the torque specs for a Ford F150?

These specs are for a 13 and should be all the same with exception to the lower front shock/strut mount as it is different on the 14. The 13 has one huge thru bolt, the 14 has a standard lower shock mount twin bolts. Don’t have the spec on those so use your best judgement by remembering how tight they felt coming off.

What kind of torque does a Ford Mustang have?

BALL JOINT CLAMP BOLT 36 (49) LOWER CONTROL ARM PIVOT BOLT 30-33 (41-51) STABILIZER BAR BOLT FESTIVA 40-50 (54-68) TRACER 10-13 (14-18) STRUT-TO-KNUCKLE BOLTS 68-72 (90-95) TIE ROD NUT 22-33 (30-45) UPPER STRUT BOUNT BOLTS 15-18 (20-24) WHEEL STUD BOLTS 63-85 (85-115)

How much torque does a Ford Expedition have?

Discussion in ‘ Suspension ‘ started by Jackmldog, Mar 6, 2011 . One ft-lb of torque is equivalent to 12 in-lbs. The below values are all in ft-lb unless otherwise stated. Hope this helps some people who don’t have manuals.

What are the torque specifications for a Ford Fiesta?

FORD (IMPORTS) APPLICATION FT-LBS / ( N-m) AXLE SHAFT FLANGE BOLTS 28-32 (38-43) AXLE SPINDLE NUT FIESTA 150-175 (205-235) ALL OTHERS 145 (197) BALL JOINT CLAMP BOLT 36 (49) LOWER CONTROL ARM PIVOT BOLT 30-33 (41-51) STABILIZER BAR BOLT FESTIVA 40-50 (54-68) TRACER 10-13 (14-18) STRUT-TO-KNUCKLE BOLTS

What are the torque specs for a Ford Taurus?

Ford torque specifications TORQUE SPECIFICATIONS FORD/MERCURY/LINCOLN APPLICATION FT-LBS / ( N-m) AXLE SPINDLE NUT PROBE 174-235 (235-319) ALL OTHERS 180-200 (244-271 BRAKE CALIPER BOLT (PROBE) 58-72 (79-98) CONTROL ARM-TO-KNUCKLE NUT SABLE & TAURUS 40-55 (54-75) ALL OTHERS 37-44 (50-60) CROSSMEMBER-TO-FRAME BOLT

How much torque does a Ford 4.6L Engine have?

Torque Romeo jackscrews to 4 ft-lbs, and then 7 ft-lbs. Torque cross bolts to 14 to 17 ft-lbs. Torque Windsor cross bolts to 20 to 24 ft-lbs, and then 85 to 95 degrees with a torque-angle gauge. Measure the crankshaft on a stock 4.6L Modular engine for an endplay of .006 to .012 inch. It should be closer to .014 inch if you’re going racing.

How to Assembly a Ford 4.6L engine step by step?

Torque the main caps with a 13-mm socket to 27 to 32 ft-lbs, and then to 85 to 95 degrees on the torque-angle gauge. Install the dowel pins and hammer them into place. Next, install the cross bolts (also called side bolts) from the outside and torque them to 20 to 24 ft-lbs, and then 85 to 95 degrees. The Windsor block has no jackscrew adjusters.

What kind of torque does a Windsor engine have?

With dowel pins (Windsor engines), all you have to do is tap them in place before installing cross bolts. Torque Romeo jackscrews to 4 ft-lbs, and then 7 ft-lbs. Torque cross bolts to 14 to 17 ft-lbs. Torque Windsor cross bolts to 20 to 24 ft-lbs, and then 85 to 95 degrees with a torque-angle gauge.

What kind of torque does a Ford F-150 have?

Type: Bolt 130 1560 Gen X 150/250 – FRONT Hub/Bearing Assembly Bolts (4WD) Type: Bolt 150 1800 Gen X 150/250 – Idler Arm Bracket to Frame Bolts Type: Bolt 56 672 Type: Stud 86 1032 Type: 85 1020 Gen X 150/250 – Leaf Spring FORWARD Thru Bolt Type: Bolt 86

What are the torque specifications of a Ford 5.4L V8?

Type: Bolt Engine Mount To Engine Block 45 540 61.01 Modular OHC – Engine Mount to Engine Block Bolts Type: Bolt Head: Hexagon 45 540 61.01 Modular OHC – Engine Mount Thru Bolts Type: Bolt Exhaust Manifold To Cylinder Head 18 216 24.4 Modular OHC – Exhaust Manifold NUTS Type: Exhaust Manifold To Cylinder Head 9 108 12.2

How much torque does a 4.6L SOHC engine have?

These ARP main studs have been installed in the 4.6L SOHC block, so this is not a torque-to-yield installation. Torque main studs in a conventional manner to ARP specifications in onethird values. The total torque is 60 to 65 ft-lbs. Once you have torqued the main studs nuts, check the torque again.

Where can I find the latest torque specs?

Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.

What kind of shocks does a Ford F-150 have?

2006 Ford F-150 Specifications Front 4×2 Coil-on-shock, long-spindle double wishb 4×4 Coil-on-shock, long-spindle double wishb Rear

What are the specs of a 2006 Ford F-150?

2006 Ford F-150 Specifications POWERTRAIN 4.2L V-6 4.6L TRITON V-8 5.4L TRITON V-8 Power 202 hp @ 4350 rpm 231 hp @ 4750 rpm 300 hp@ 5000 rpm Torque 260 lb-ft @ 3750 rpm 293 lb-ft @ 3500 rpm 365 lb-ft @ 3750 rpm Oil Capacity 6 qt 6 qt 7 qt Coolant Capacity 19.7 qt 20.0 qt 20.7 qt

What is torque setting for front axle nut?

I have a 2006 2wd f-150. The right front wheel bearing went out and I just replaced the rotor assembly. Since it has the sealed bearings pressed into the rotor and upon removal I realized that the nut was much much tighter than I thought it should be, I want to know the correct torque setting for putting it back on.

How much torque does a front axle nut have?

Description: FWD, RWD & 4 W/D front axle nut torque specifications Front proc. Rear proc. Make or torque or torque year Model ft-lbs/Nm ft-lbs/Nm Front proc. Rear proc. No Text Content!

How much torque does a Ford 5.4L 330ci have?

21.69 Mod OHC – STEP 5 (REP): Side Bolts Type: Bolt Cylinder Head To Engine Block 30 360 40.67 Modular OHC – 3 Steps: 30FtLbs; +90deg; +90deg Type: Bolt 11 132 14.91 Modular OHC – Oil Drain Plug

Is there a torque specifications repair guide for Commander?

Find out how to access AutoZone’s Torque Specifications Repair Guide for Commander 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guide for 300, 300C & Magnum 2006-2008, Charger 2006-2008. Find out how to access AutoZone’s Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005.

What kind of OHC does a Ford 5.4L have?

Type: Engine Block To Transmission 36 432 48.81 Modular OHC – Transmission to Engine Block Type: Bolt Engine Mount To Engine Block 45 540 61.01 Modular OHC – Engine Mount to Engine Block Bolts Type: Bolt Head: Hexagon 45 540 61.01 Modular OHC – Engine Mount Thru Bolts Type: Bolt

What are the torque specs for front suspension?

Front Suspension Torque Specs Chart Item Nm Lbft Front lower control arm to frame 135-162 100-110 Front lower ball joint to spindle 106-163 80-120 Upper A-arm to frame 135-162 100-110 Upper ball joint to Spindle 95-122 70-90 Spindle hub nut 305-338 225-250 Tie Rod end to Spindle 33 25

How to replace rear shocks on Ford F-150?

1 Remove the rear tire. Loosen the lug nuts with the truck still on the ground. 2 Jack up the rear of the truck. Make sure the truck is parked on a leveled surface and block the front wheels. 3 Remove the old shocks. Remove the upper and lower shock retaining bolts. 4 Attaching the new shocks. 5 Take your truck for a test drive.

When to replace shocks on Ford Super Duty?

If you notice that your F-150 or Super Duty’s ride is not as smooth as it used to be, then it’s probably time to replace them. A quick way to test them is to push down hard on your truck’s bed.

What are the torque specs for a Ford F150?