What happens when you press down on the gas pedal?

Engine response is inconsistent When you press down on the gas pedal, your engine should respond directly and instantly. However, when a problem with the APP sensor exists, the vehicle’s ability to consistently accelerate or decelerate as directed by the driver is reduced.

When do you need to replace the gas pedal?

Although this device often lasts the entire lifespan of your vehicle, there are occasions when it will fail, wear out, and need to be replaced. The APP sensor essentially tells your engine how fast or slow to drive when you press the gas pedal.

What are the signs of a bad pedal position sensor?

Common signs of a faulty pedal position sensor include inconsistent engine response, reduced fuel efficiency, and the Check Engine Light coming on. 1. Engine response is inconsistent 2. Engine does not run efficiently 3. Check Engine Light comes on Average rating from 129,472 customers who received a Vehicle Engine Electrical Inspection.

What happens when the accelerator pedal goes bad?

When the Accelerator Pedal Position (APP) Sensor 1 goes bad, you’re gonna’ see the following symptoms: Check engine light will be lit on your instrument cluster. P0121: Accelerator Pedal Position (APP) Sensor 1 Circuit Performance. P1125: Accelerator Pedal Position (APP) System.

What should I do if my engine is surging?

There may be a fault in the computerized engine control system. Check engine control systems with a scan tool. Have a mechanic test the circuits and repair or replace components as required, since this is generally not a DIY job. The fuel filter may be partially clogged. This is an easy fix! The fix: Replace the fuel filter.

When to call a mechanic for a bad gas pedal sensor?

If any of these symptoms occur or your car isn’t responding accurately when you press the gas pedal, you should pull over immediately and call a mechanic. Here is a more detailed list of the most common symptoms of a bad accelerator pedal position sensor.

How to fix a surging engine in a car?

Easy step by step guide on how to repair an automotive engine that is surging, this information pertains to most vehicles and is listed in the order of popularity. Start with the vehcile on level ground, engine “OFF” in park with the emergency brake set, wear protective gloves and eye wear for safety.

Why does my Chevy Tahoe stall while driving?

Bad fuel or fuel starvation could cause some stalling too! I had a car once that developed a small hole in a rubber fuel line causing the car to **** air and stall. Check you fuel lines especially if they are rubber.

Can a Chevy Tahoe shut off while driving?

When driving tahoe the engine shuts off sometimes can restart, but now it took 24 hrs before restarting chevy garage check codes nothing Clicking this will make more experts see the question and we will remind you when it gets answered.

What happens when you take your foot off the gas pedal?

Engine dies when I take my foot off gas pedal. lexus engi… Q: Engine dies when I take my foot off gas pedal. The engine dies when I take my foot off of the accelerator. Hello. If the engine runs fine when you are holding the accelerator pedal down and dies when you release it then you may have a couple of possible issues.

Is there a left foot accelerator pedal for cars?

Our Left Foot Accelerator Pedal is the BEST KEPT SECRET for those with a desire to become more independent. Able Motion Mobility Left Foot Accelerator Pedal is designed to provide you with the ability to drive any vehicle with your left foot. The LFA acts and feels like an existing factory pedal.

Why does my car not respond when I press the gas pedal?

You may not be noticing a delayed response from the pedal, but if you see low gas mileage, it could mean that the car’s throttle position sensor is working but not as accurate as it should be. Modern cars have a monitoring system over all the sensors in the car engine.

What should I do if my accelerator pedal is bad?

In such a case, it is advised to pull over immediately and call a mechanic since bad pedal timing can prove to be fatal. The optimal RPM of a car engine is around 600 to 700 rotations per minute. At these RPMs, the engine idles smoothly without shaking and consumes little fuel.

Why does my car not accelerate when I press the gas pedal?

This sensor sends a reference voltage to your power-train control module, which uses that to determine ignition timing and fuel trims. If the power-train control module is not detecting the proper signal from the throttle position sensor, the engine may not accelerate properly.

How does the accelerator pedal work in a car?

Today’s modern cars, trucks, and SUVs are all equipped with an electronic throttle control system that contains an accelerator pedal position (APP) sensor. This sensor’s primary job is to monitor the position of the throttle pedal and send an electronic signal to open the throttle body as you depress the gas pedal.

When do you start the car, the engine revs?

Car engine revs way up immediately upon starting engine. Q: Car engine revs way up immediately upon starting engine. When starting the engine, it sounds like you have your foot pressed to the floor on the gas pedal as soon as you start it, without even having your foot on the gas.

What are the symptoms of a bad throttle / accelerator pedal?

Symptoms of a Bad or Failing Throttle/Accelerator Pedal Position Sensor. $79.99 – $89.99. Average rating from 4,829 customers who received a Check Engine Light is on Inspection. The days of having to constantly adjust the throttle cable due to a loose nut on the carburetor are long gone.

Why are the brakes on my 2005 Chevy Trailblazer not working?

The anti-lock brake system in my 2005 Chevy Trailblazer ls at times does not work. When I apply my brake the brake makes a noise sounding like grinding, not catching or holding, slips and goes to the floor. I have to rapidly act with swiftness within a short time to reapply my brakes in hopes they work.

Where can I buy a 2005 Chevrolet TrailBlazer?

See pricing for the Used 2005 Chevrolet Trailblazer LS Sport Utility 4D. Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2005 Chevrolet Trailblazer LS Sport Utility 4D. View local inventory and get a quote from a dealer in your area. Home Car Values Price New/Used My Car’s Value Instant Cash Offer Cars for Sale Cars for Sale

How to test the GM accelerator pedal position?

The Fluke 115 digital multimeter has a bar graph… to see it, check out this article: Abe’s Multimeter Recommendation. You can use an analog multimeter too. Generic scan tool. As I mentioned above, you don’t need to use a generic scan tool to take advantage of the test info in this tutorial, but it does come in handy to read any trouble codes.

Why does my Chevy Blazer engine bog down when I hit the gas?

Take it to a good local mechanic (not a dealer) and see if this is one problem. My Blazer bogs down when you hit the gas and has trouble starting. We have replaced the MAF sensor, plugs, rotor, cap, plug wires, and fuel filter. The fuel pressure is at 50psi when idling and 64 wot when driving.

What’s the fuel pressure on a Chevy Blazer?

My Blazer bogs down when you hit the gas and has trouble starting. We have replaced the MAF sensor, plugs, rotor, cap, plug wires, and fuel filter. The fuel pressure is at 50psi when idling and 64 wot when driving. Can we have pressure without flow? Initially the code was p0171. Now that we cleared it it hasn’t come back on.

What kind of car wont start unless you press the gas pedal?

I have a 2002 avalon XLS. In the morning the car cranks but wont start unless I press the gas pedal. After that everything was fine. But recently the problem is getting worse. The car became harder to start although it will start eventually. I have changed the Mass air flow sensor, but did not solve the problem. Any suggestion?

Why does my Car start when I press the gas pedal?

When you step on the accelerator while starting the engine, this opens the throttle plate which allows air into the engine. This then allows the engine to start. waterboy July 6, 2016, 1:04am #7 If you leave the key in the on position for 20 seconds before you try and start the car and it starts right away let us know.

What kind of suspension does a blazer ZR2 have?

Autotrac also has a transfer case neutral position for towing behind a recreational vehicle. all blazers use a short-/long-arm front suspension and a live axle on leaf springs at the rear (variable-rate, multi-leaf springs on trailblazer). 4×4 models are sprung by torsion bars up front, while 4×2’s have coil springs.

How many horsepower does a Chevy Blazer ZR2 have?

This 90-degree v6 has a cast-iron block and head and overhead valves, and runs happily on 87 octane gasoline. Although redlined at 5600 rpm, it reaches its peak 190 horsepower at 4400 rpm.

What are the symptoms of a bad accelerator pedal?

Symptoms of a Bad or Failing Throttle/Accelerator Pedal Position Sensor. Common signs of a faulty pedal position sensor include inconsistent engine response, reduced fuel efficiency, and the Check Engine Light coming on. The days of having to constantly adjust the throttle cable due to a loose nut on the carburetor are long gone.

How is the gas pedal connected to the engine control unit?

Connected to the gas pedal, it is responsible for making sure that there is enough air entering your engine to meeting driving and accelerating demands. It works together with the Engine Control Unit to balance the right mix of air and fuel in your engine for the best power and performance.

What causes the accelerator pedal to stop working?

The primary reason why this part fails is due to exposure to high heat, as it’s typically located on the floorboard next to the firewall of the vehicle, in very close proximity to the engine.

How to troubleshoot a car that does not respond to the gas?

Part 1 of 2: Visibly inspect the gas pedal 1 Look for visible obstructions of the gas pedal. Look for any obstructions or objects getting in the way of the pedal. 2 Look for visible obstructions of throttle. Open the hood and look for the throttle body. 3 Look for visible damages or deformities in system. …

Why does my car not respond to the gas pedal?

Electronic throttle controls module faults are one of the most common issues when dealing with a unresponsive gas pedal. This is a sensor that reads how far you have pressed the gas pedal down and outputs that information to the computer which controls the throttle. This information is also used in computing ignition timing and other components.

Why is my Chevy Blazer not getting gas?

Pressing the gas pedal does not give it more fuel. Taking the throttle body sensor off makes no difference either. Took it to a mechanic for a “professional” diagnosis – they told me it was the fuel injection system. Put a new one on this weekend, still no dice. Can’t move the truck as it won’t get gas.

What causes acceleration in a 97 Chevy Blazer?

97 chevy blazer 4.3 idles great but upon acceleration it starts to surge, changed just about everything, fuel pump,cap rotor, wires, plugs distributor injectors, crankshaft, cam, throttle pos. sensor, tried new computer, at a loss starts right up and idles great, take in down the road and starts surging. Exhaust?

Why does my Chevy Blazer have a yellow warning light?

A night before i set on a journey from Switzerland to Germany my car show yellow warning light which warn about fuel, power etc the symbol look like a videocamera diagram. After about 3 hour drive the car stop to accellerate. I listern to the fuel pum sound it sound fine but road patrol said the fuel dont run to injector.

Why does my car hesitate when I step on the gas?

When you go to step on the gas pedal to accelerate, you will suddenly feel like the power has been lost in the engine for a couple of seconds. Instead of going faster by stepping on the accelerator pedal, the speed will be reduced. The vehicle may even stumble entirely during these seconds. This is what it means when the car engine hesitates.

What are the symptoms of a bad accelerator pedal sensor?

In this article, you will find the most common symptoms of a bad accelerator pedal position sensor 1. Your car hesitates to move when the gas pedal is pressed 2. The engine doesn’t idle smoothly 3. Your car doesn’t accelerate over a specific limit 4. Your car won’t shift up or jerks upon depressing the pedal 5. You experience low gas mileage

What does it mean when your car hesitates when accelerating?

Why does my car hesitate when I press the gas?

Due to these facts, problems with the fuel pump can cause the engine to not run or to stumble as the gas pedal is applied. Typically hesitation or stumbling issues are caused by an obstruction in the fuel pump or a pump that is starting to show signs of breaking or wearing out.

Why does my car hesitate to accelerate?

Choose your car for a more accurate estimate. There are a number of things that may cause the car to hesitate when accelerating such as low fuel pressure, a dirty or faulty mass air flow sensor, clogged or dirty fuel injectors, a faulty throttle position sensor or potentially a bad fuel pump.

Why does car hesitate on acceleration?

A dirt or damaged fuel pump can trigger a handful of issues and the aging in acceleration is one of them. The pump spurts fuel to the engine. When it does not function properly, the fuel can hardly reach the engine, making the car hesitates when accelerating from stop.

What causes hesitation on acceleration?

One of the most common causes of stumbling or hesitation during acceleration is a fouled spark plug (or plugs). This is a simple diagnosis and a simple fix. Remove the plugs and check the electrodes for wear and/or oil fouling them.

What are the symptoms of a bad clutch hose?

Symptoms of a Bad or Failing Flexible Clutch Hose. Common signs include difficulty shifting, low clutch fluid, and feeling no resistance at the clutch pedal. Rules of the Road For Iowa Drivers. Driving Driving on the roads requires knowledge of the rules, many of which are based on common sense and courtesy.

So when the stoplight turns from red to green, you punch the gas pedal, hoping to sail through the intersection a little, um, faster than usual. But instead of moving when you hit the gas pedal, your car hesitates. Juuust long enough for every car behind you to honk, flip you the bird, or angrily swerve around you.

How long does it take for pedal stroke to develop?

This study shows that a fast and powerful pedal stroke doesn’t take years — or even weeks — to develop in a reasonably athletic person. In these athletic subjects it took only 3 days and 12 total sprints — less than 40 seconds of actual work! Martin cited 2 other important points.

How is the force measured in a pedal stroke?

Biomechanists like Broker use force-measuring pedals to quantify the direction and force exerted by the foot through every portion of the 360-degree pedal circle. Other equipment measures which muscles fire as we pedal.

When to press down on the gas pedal?

1. Engine throttle is inconsistent When you press down on the gas pedal, your engine should respond directly and instantly. However, when a problem with the APP sensor exists, the vehicle’s ability to consistently accelerate or decelerate as directed by the driver will be reduced.

Symptoms of a Bad or Failing Throttle/Accelerator Pedal Position Sensor 1 Engine throttle is inconsistent When you press down on the gas pedal, your engine should respond directly and… 2 Engine does not run efficiently When the APP sensor is not functioning properly, it will also have problems with fuel… 3 Check Engine Light comes on More

Why does my Dodge Ram keep bogging down?

The other thing it may be is a defective pressure regulator. Again, if it restricts flow, you may be starving the engine under wider throttle settings. Good luck. Hope one of those ideas helps. Try the fuel filter first, as it is cheap and easy. 28 people found this helpful. 20 people found this helpful. 7 people found this helpful.

What to do if your Dodge Ram has no power?

To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Find Our Videos Helpful? Consider Supporting!

Why does my Dodge Ram get run rich?

They get dirty and misread, causing a run rich condition. This clogs a cat faster than anything, but no code as the sensor is working correctly from an electrical stand point. With a little luck, the cat will gradually unclog, although you may well need a new one at this point.

To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Find Our Videos Helpful? Consider Supporting!

What to do if your Dodge Ram gets run rich?

The first thing I would do is change the O2 sensor (s). They get dirty and misread, causing a run rich condition. This clogs a cat faster than anything, but no code as the sensor is working correctly from an electrical stand point. With a little luck, the cat will gradually unclog, although you may well need a new one at this point.

What causes the engine to go up in idle when pushing the brakes?

When you depress the brake pedal, some of the engine vacuum is bled off to power the brake booster. The engine senses this decrease in vacuum the same as it would a decrease in vacuum caused by stepping on the accelerator pedal and increases the flow of fuel through the injection system in response.

Why does my car slow down when I push the gas?

A clogged air filter means no enough air-fuel ratio gets into the engine resulting in slow acceleration. This is the most sensitive car engine element that plays a vital role in car acceleration. A damage as small as a misaligned tooth can cause noticeable changes to the acceleration of the car.

What happens when you press the gas pedal all the way?

I tried to press the gas pedal all the way, but there is no changes in RPM or acceleration. I had the filters replaced. It would sometimes run normally if I release the gas pedal and press it again. What could be the problem?

When do car RPMs go up or down?

The RPMs did not go above 3000. The RPMs also got a shaky and moved back a forth a bit. On the highway the car slowly got up to 45 MPH and 3500 RPM, then it was stuck there for about 15 seconds – it would not go any faster and RPMs would not go higher. After those 15 seconds it finally went above 3500 and got up to 60.

What does it mean when your car engine is sluggish?

Engine sluggishness would be a symptom of incomplete combustion, since coolant is entering the cylinders. Continued sluggishness in neutral rules out most transmission issues. Symptoms for the LIM gasket are similar to the head gasket, except the coolant does not directly enter the cylinders.

What causes the advance piston to stick on a Dodge 24?

The problem will most likely be an internal VP44 fault caused by low or no fuel supply pump pressure. This causes the advance piston to stick in the advance housing bore due to cavitation damage. Another cause could be from faulty lead free soldered connections that fail over time in the pump PSG.

How to change the accelerator pedal release position?

Accelerator Pedal Release Position Learning Procedure. Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.

How long does it take to install an exhaust system?

An MBRP performance exhaust system is the starting point to getting the most from cold air intakes, programmers, modules and downloaders. Easy InstallationMBRP systems are as much fun to install as to drive with on your truck. Bolt-on, no weld design makes installing this on your truck a no hassle one and a half to two hour project.

What kind of exhaust system does Dodge 5.9L Cummins use?

The Magnaflow 17876 5″ Pro Series Cat-Back Exhaust System provides a custom look and increased exhaust flow on your 2003-2007 Dodge 5.9L Cummins. The Pro Series has a lifetime backed stainless steel construction, it’s the best value system with a no hassle emissions legal design.

What causes an exhaust manifold to crack on a Cummins 5.9L?

While the block will only expand by a fraction of an inch, the constant expansion and contraction causes a lot of stress on the exhaust manifold. As a result, the manifold (also made of cast iron) can crack. When the manifold cracks air leaks out, pressure is lost, and the engine loses vacuum.

What happens when the ECM sensor fails on a Cummins 5.9?

When the sensor fails, the ECM doesn’t receive a signal from the pedal, therefore not knowing what to do with engine speeds. This problem is mostly limited to 1998-2004 Cummins 5.9’s. When the sensor fails it usually sends no signal to the ECM.

Why does my car hesitate when I press the clutch?

Step 10 – The clutch is designed to release the engine from the transmission, when this part wears it can cause a hesitation in the motion of the car. To test this condition drive the car at a steady speed, then very lightly tap the clutch pedal, if the car responds the clutch is worn.

When you press down on the gas pedal, your throttle body unit’s valve opens. This causes your throttle position sensor to adjust the engine intake manifold accordingly. This little sensor is essential to a correct mixture of air and fuel. It’s integrated with your engine control module and helps keep your idling and acceleration smooth.

What does it mean when your engine hesitates under load?

An engine that hesitates, stumbles or misfires when accelerating or when it is under load, is an engine that is either sucking too much air, not getting enough fuel, or misfiring. If the Check Engine Light comes on, you may find any of the following codes: P0171, P0174 Lean fuel condition codes P0120 to P0124 Throttle position sensor codes

Why does my car hesitate when I step on the accelerator?

Instead of going faster by stepping on the accelerator pedal, the speed will be reduced. The vehicle may even stumble entirely during these seconds. This is what it means when the car engine hesitates. It is usually the result of a problem with the air and fuel mixture within the combustion chamber.

What does it mean when your engine idles rough?

For example, when your engine idles rough, you may notice the problem only shows up before the engine warms up; then idle smooths out. This may indicate a bad ECT sensor as described in Other symptoms in that section. So pay attention to all the symptoms and conditions when given in each component listed to make your diagnostic easier.

The primary reason why this part fails is due to exposure to high heat, as it’s typically located on the floorboard next to the firewall of the vehicle, in very close proximity to the engine.

Can a poor fuel pressure regulator cause a Ford to stall?

A poor fuel pressure regulator can also cause your Ford to stall while idling or driving. While it will most likely occur while idling, it is not unheard of for the car to stall while you are driving down the road.

How to fix a car with no gas pedal?

Leave the jumper connected for about 2-mins. 3) Reconnect the negative battery cable to the battery. Turn off all electrical accessories before proceeding. Turn off headlights, blower motor, radio, wipers, etc. 4) Turn the key to run and wait for all warning lights to turn off.

What to do if your accelerator pedal fails?

In order to work properly, all of the sensors inside your car must function at 100 percent efficiency. When the APP fails, it impacts the operation of the entire vehicle. Anytime you notice any of the above symptoms or warning signs, you should contact a local ASE certified mechanic through YourMechanic.

How does the throttle react to the gas pedal?

When the car ISN’T running, the throttle reacts to the gas pedal. By that I mean I used a mirror and can see the butterfly open and close in sync with the pedal actions. When the car IS running, the throttle does not react at all.

Why does my car stall when I step on the gas?

Rough idling, frequent stalling, and inconsistent acceleration are all signs that something is amiss with your car. There are a number of systems that can cause this problem. Everything from electrical to fuel delivery to vacuum system issues can all cause a rough-running, stalling vehicle.

Why does my car shut off when stepping on the gas pedal?

received a Car shuts off when stepping on gas pedal Inspection. Rough idling, frequent stalling, and inconsistent acceleration are all signs that something is amiss with your car. There are a number of systems that can cause this problem.

What should I do if my fuel line is leaking?

Be extremely cautious when dealing with a leaking fuel line. Never drive a vehicle with a leaking fuel line. If the rupture line is rubber, simply remove the hose clamps on either end and replace that stretch of rubber line. If it’s a steel line, you may need a professional mechanic to repair the leak.

How can I tell if my Ford Escape has a problem?

Thankfully driving slowly in a parking lot and the car stalled out with no warning lights. I tried to turn the engine over, and when it finally started up, the car idled at the normal RPMs for about 1 minute, then dipped quickly below 500, then sputtered out.

Can a Ford Escape lose power while driving?

Many customers state that while driving their vehicle, the engine will hesitate, stumble, or lose power. In more severe cases, the EGR valve can be physically damaged.

How much does it cost to replace a Ford Escape valve?

In some models, the DPFE sensor is integrated into the EGR valve, and must be replaced together. The average cost for a Ford Escape EGR Valve Replacement is between $207 -$218. Learn More

Are there any problems with the Ford Escape?

Like any vehicle, the Escape may develop some transmission problems including fluid leaks, erratic shifting and outright transmission failure. However, there are some troubleshooting techniques that can remedy these problems.

Why does my Ford Escape not shift into reverse?

Pay attention to how the vehicle shifts. If it is erratic or rough, or if it fails to shift into reverse, this could mean a problem with the drive shaft’s joints or it could be low transmission fluid levels. Check the fluid level with the dip stick.

How do you know if your Ford Escape has a transmission problem?

What causes idle surges on a car ECM?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges.

Can a poor fuel pressure regulator cause a car to stall?

Under acceleration, the vehicle should accelerate smoothly no matter how hard or light the gas pedal is depressed. If the Ford will not accelerate smoothly, but instead jerks and jumps under acceleration, your fuel pressure regulator should be inspected. A poor fuel pressure regulator can also cause your Ford to stall while idling or driving.

Why does my Ford Taurus stall at idle?

Problem With Idle Air Bypass Valve May Cause Engine Performance Problems Engine Stalling and/or Hesitation on Acceleration due to Faulty Idle Air Bypass Valve on Ford Taurus Problem Description

What’s the cost of a Ford Taurus idle valve?

This valve helps the vehicle idle steady when the accelerator pedal is not pressed. The average cost for a Ford Taurus Check Engine Light Diagnosis & Testing is between $88 -$111. Learn More My Taurus want stay running unless I keep my foot on the gas.

What happens if you have a bad accelerator pedal?

However, when a problem with the APP sensor exists, the vehicle’s ability to consistently accelerate or decelerate as directed by the driver is reduced. This could cause a serious safety hazard, as the driver is not able control the speed or acceleration of the vehicle.

Why does my car not start unless I press the gas pedal?

In the morning the car cranks but wont start unless I press the gas pedal. After that everything was fine. But recently the problem is getting worse. The car became harder to start although it will start eventually.

What happens when you depress the accellerator pedal?

If you depress the accellerator pedal in a fuel injected vehicle, it opens the throttle plate, all this can do is make air available, and give the throttle position sensor a reading. more air would flow over your MAF.

Why is my Chevy Cavalier running out of gas?

I forgot it running, it ran out of gas and sat until the battery went dead with the key in the “on” position. Now it won’t start. Security light, check gauges and service lights all stay on. Gas gauge doesn’t register any gas (I put 4 gallons in). Very little gas pressure. Has power to the ICM. No power to fuel pump. Any ideas? Thanks.

Why does my Cavalier stall at a stop sign?

I have a 2004 cavalier and when I am stopped at a stop sign the car acts like it wants to die, I have to put it in park and push in on the gas so it dosen’t die. I changed out the fuel filter and air filter. anyone have any ideas on what it can be?

What’s the problem with my Chevy Cavalier Rs?

I have a 91 Chevy Cavalier RS, 2.2 L. Recently, I’ve noticed an intermittent problem when starting the car (both cold start and warm start). I thought at first it might have been the key, because the keys we had were cheap, badly made Wal-Mart copies so we had a locksmith make an exact replica from the manufacturer’s guide he had.

Where are the wires on a Chevy Cavalier?

There is a gray wiring harness / connector on the driver side under the air intake tube.It must have 16-24 wires going in and out of it. He shook it and it started.

What causes a GM truck to lose power?

If your GM truck occasionally loses the ability to accelerate and warns you of reduced engine power, that could be caused by a faulty throttle body. While not common, this issue can interfere with your engine function and cause your vehicle to lose power anywhere from once in a while to several times in a day.

What to do if your Chevy Silverado loses power?

While generally the Chevy Silverado is a premium, reliable truck, there are times when even the best vehicles can end up having problems. If you’ve ever had your Chevy Silverado or GMC Sierra suddenly lose power, you may be wondering exactly what is going on with your truck.

What happens when you press down on the gas pedal?