Easy lifehacks

Are there any electrical problems with the Ford Expedition?

Are there any electrical problems with the Ford Expedition?

A friend of mine who does car audio installs said that he has dealt with a couple of FOrd electrical issues while installing and said a FOrd tech told him ther have been known issues in teh ignition switch when moisture is present as well as actual problems with the factory radio.

Why does my Ford Expedition stall out while driving?

It now stall out 10 minutes on the DOT after starting… after idle or driving. That tells me its not mechanical and must be something electrical getting hot and shorting out or losing contact. Usually its starts back up and I floor it to wherever I have to go with no problems but past two weeks it wouldnt start back up and had it towed twice.

What kind of car is 2002 Ford Expedition?

I just got a V8 4.5L 2WD 2002 Ford Expedition and the first thing I ever noticed at the dealer was the windshield washer light was lit. I spoke with the used car dealer manager and he said he already ordered the new washer fluid’s container with sensors attached.

How long does it take to replace a Ford Expedition door?

Give that a shot as it resolved my issues except for the back up aid. It is super easy to uninstall/reinstall the new one, and it only runs like 40-60 bucks on e-bay and takes 1 hour (its plug and play, for lack of better terms) to install. The door sounds like a different problem all together though.

Why are my headlights not working in high beam?

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

Why are the lights on my dashboard not working?

Adjust the dial or knob to see if that fixes the problem. If the switch was accidentally bumped, your dashboard lights might have been turned off. Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb.

Why are the lights on my car not working?

If the switch, fuses, and bulbs are not to blame, you likely have a wiring or electrical issue and will need to take your vehicle to a certified mechanic for diagnosis and repairs.

A friend of mine who does car audio installs said that he has dealt with a couple of FOrd electrical issues while installing and said a FOrd tech told him ther have been known issues in teh ignition switch when moisture is present as well as actual problems with the factory radio.

Why is my car’s high beam light not working?

Make sure to use the right high beam bulb for your vehicle. On some vehicles, particularly those with HID headlights or solid-state circuit protection (Zener diodes or high beam circuit breakers) installing the wrong bulb might result in intermittent headlight operation or no high beams at all.

I just got a V8 4.5L 2WD 2002 Ford Expedition and the first thing I ever noticed at the dealer was the windshield washer light was lit. I spoke with the used car dealer manager and he said he already ordered the new washer fluid’s container with sensors attached.

What happens if the headlight switch does not work?

If the headlight switch completely fails it may prevent all of the vehicle’s lights from functioning. You may find that when you go to turn on the headlights, none of the modes will turn on any of the lights. A vehicle without any functioning lights is not safe to drive, especially in low light and nighttime situations.

What is the fuse relay on a Ford Expedition?

It is the fuse relay. At Ford Dealership, the item is listed part # F5TZ*14N089*B RELAY LIST PRICE $16.24. This relay has been replaced twice in our 2003 Ford Expedition. We were on the interstate when our vehicle shut down completely and had hard time maneuvering it.

How can I get my Ford Expedition back on the road?

Everything is on hand and ready to ship, so you can get your Ford Expedition back on the road in just a few days. Ordering Ford Expedition spark plugs, fuel injectors, and other parts and accessories only take a few clicks. Just enter your vehicle’s model year into our website’s vehicle selector to limit the results to compatible products.

Why is my Ford dash not working anymore?

Thought that was strange that the dash was having issues. On my drive back home basically nothing was working on the dash. Can someone explain if this was due to the dead battery cocking things up? or something else that’s playing up, and what would be the possible fix.

What to do if your Ford dashboard light comes on?

Make an appointment with your local dealer as soon as possible. Charging System: If you’re driving while this light comes on, switch off all unnecessary electrical equipment that you may have running and get your vehicle checked by an authorized mechanic immediately.

Why do I have no dash lights on my 1997 Ford F150?

Another common cause of a ‘no dash lights’ problem, that I’ve seen a lot, is an installation done incorrectly of an aftermarket component like a radio, gauge, etc. The following links will help you comparison shop for the headlight switch on your 1997-1998 Ford F150, F250, and Expedition:

What do the warning lights on the dashboard mean?

Only a flashing red light means pull over immediately. There are three dashboard light colors on most dashboards: yellow, red, and orange (and, occasionally, blue or green). The most severe alerts are displayed in red or orange.

What are the colors on the Ford dashboard?

There are three dashboard light colors on most dashboards: yellow, red, and orange (and, occasionally, blue or green). The most severe alerts are displayed in red or orange.

What does it mean when a Ford Escape lights up?

Have the system checked by your authorized dealer immediately. Lights up while a chime sounds to remind you to fasten your safety belt. A malfunction is indicated if this warning lamp fails to illuminate when you start your vehicle, continues to flash or remains on. Have the system checked by your authorized dealer.

Make an appointment with your local dealer as soon as possible. Charging System: If you’re driving while this light comes on, switch off all unnecessary electrical equipment that you may have running and get your vehicle checked by an authorized mechanic immediately.

Where is the fuse panel on a Ford Expedition?

Year of production: 2003, 2004, 2005, 2006. The fuse panel is located under the right-hand side of the instrument panel.

How can I find out if my Ford battery is dead?

Here’s a test to use with a Ford vehicle. If you’ve suffered a dead battery and both the battery and charging systems check out, it’s time to perform a parasitic drain test. The test involves hooking an ammeter in series with the negative battery cable to measure the amperage draw. Professional technicians use a clamp on ammeter.

What should I do if my car battery is draining?

If you can’t find the cause of the battery drain, a manual draw check of the electrical system will need to be performed. With the ignition key in the off position and the doors closed (driver’s side window down) disconnect the battery cable on the negative side.

How often does a 2001 Ford Expedition surge?

If you are driving a 2001 Ford EXPEDITION, or if you are planning to purchase one, then it is important that you review reported Electrical System problems and defects. Total reports: 73. While Engine Isideling, Vehicle Will Surge Foward Without The Drivers Foot On The Gas, This Has Occurred A Total Of Five Times.

What kind of transmission does a 2001 Ford Expedition have?

FORD EXPEDITION 2001 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph. Whenever Vehicle Has Been Started And Running For A Minute It Would Suddenly Cut Off For No Reason. At The Time The Vehicle Would Have 1/4 Tank Of Fuel. Vehicle Not Able To Be Restarted.

Why does the tail light stay on when the car is turned off?

There are many causes for tail light constantly staying on while the car is turned off: A broken brake light switch, damaged trailer light plug, faulty brake light switch stopper, broken wiring harness,… There are various reasons, however, you can check whether it is the brake lights or the tail lights to see which are the parts having problems.

Why are the tail lights on my Jeep not working?

If it is the tail lights that are inop there are some common problems associated with this model Jeep. The most common is the tail light sockets. They often melt the housing they fit into and consequently lose ground. The only way to properly fix this is by replacing the entire taillight assembly” italic text”.

Why does my Ford Expedition have a battery warning light?

“Island cars” tend to have problems based on inactivity. I’d put some miles on the car and see if it fixes itself. Hop on the ferry, drive to Cleveland, and watch the Indians afternoon game. Put some heat in the whole system. Update.

What kind of battery does Ford Expedition have?

It is a 2012 Expedition with a 5.4 L engine. I tested the battery with a load tester, and it was good. Also the load tester after starting tested in the green, so 14 volts. My volt meter on the dash is straight up in the middle where it should be, and appears to be working.

What does battery gauge look like on expedition?

As the alternator starts to die, the gauge (presuming an analog one) will look like a slow tail wag as the system voltage goes from the 14.X to 12.X range and back. The cycles usually took ~20 minutes to go back and forth. Neither of my Expeditions can go a month without the battery being dead.

What should I do if my lamp is not working?

Plug another lamp or electrical item into the same socket that the lamp was in, just to make sure it’s not a fault in the socket. If that item works fine, you have eliminated an outside source, so you know it is definitely the lamp that is faulty.

What to do when your headlamps are not working?

If both headlamps are flickering, check the part of the circuit that controls both lamps: Flip the switch to low- and high-beam, and see if the lights flicker in both modes. Check the switch. Check for loose wires at the switch. Check the multifunction switch. Check the power side of the circuit for a loose wire or connector.

How can you tell if a lamp is faulty?

Plug another lamp or electrical item into the same socket that the lamp was in, just to make sure it’s not a fault in the socket. If that item works fine, you have eliminated an outside source, so you know it is definitely the lamp that is faulty. 2. Secondary Assessment

Why are there fumes in my Ford Expedition?

Fumes seem also to be either entering the cabin in the rear cargo area, or gathering there and being distruibuted by the rear heat-cool system ventilation fan through the ceiling air ducts. Ford has tried repeatedly to diagnose and fix the problem, but seems to be having trouble identifying the cause.

What to do with a Ford Expedition 4WD?

Select 4x4H and i hear solenoid by the seat belt click. 4×4 indicator illuminates on the dash and only have rear tire spin. Put trans in neutral, foot on brake, select 4x4L. Transfer case engages in low range and 4x4L indicator illuminates.

How can I Fix my Ford Expedition leak?

Since re-soldering all nine of the connector pins on the circuit board and cleaning the sloppy solders and rosin from the back of the board, I have driven 1000+miles with no problems whatsoever. This has clearly solved the problem. Hi I have a 01 Ford expedition and like everyone else I am having the same leak problems.

Fumes seem also to be either entering the cabin in the rear cargo area, or gathering there and being distruibuted by the rear heat-cool system ventilation fan through the ceiling air ducts. Ford has tried repeatedly to diagnose and fix the problem, but seems to be having trouble identifying the cause.

How is the transmission of a Ford Expedition controlled?

Electronic transmissions are controlled by a computer, otherwise known as the powertrain control module (PCM). Troubleshooting the PCM is a complex job that requires some special test equipment that the average do-it-yourselfer does not have—nor is cost effective for them to purchase.

Give that a shot as it resolved my issues except for the back up aid. It is super easy to uninstall/reinstall the new one, and it only runs like 40-60 bucks on e-bay and takes 1 hour (its plug and play, for lack of better terms) to install. The door sounds like a different problem all together though.

Where to find failure code on Ford Expedition?

Plug the code scanner into the OBD port on the left underside of the steering column. Press the key marked “Read” and the scanner will display any failure codes for the faults it has recognized. The code is a letter followed by four numbers.

How can I tell if my Ford Expedition battery is bad?

Check the battery voltage with the voltmeter. Connect the red voltmeter lead to the positive terminal and the black lead to the negative terminal. The voltage should read 12.5 to 12.75. If the voltage is one or more volts lower, the battery is discharged or has a bad cell. Charge the battery and retest.

Is there a problem with the Ford Expedition?

Ford has tried repeatedly to diagnose and fix the problem, but seems to be having trouble identifying the cause. They are willing it fix it, but so far have not figured out the cause.

Are there any problems with the liftgate on my Ford Expedition?

Recently (and intermittantly) it has had problems opening and closing. It acts like a garage door opener with sensor problems and refuses to open or close. Just had it in to the dealer on two occasions for this problem.

Why does my Ford Expedition door not lock?

“My expedition has the door ajar on the message center but no doors are ajar. This in turn causes the lights to not go out and the door locks to not lock automatically and when you take the key out of the ignition the radio goes off instead of staying on until you open the door.”

Is the Eddie Bauer expedition a 4 wheel drive?

My 99 Expedition Eddie Bauer has full time 4 wheel drive. Or at least it has A4x4 on the switch. WHen turning steep into a parking space or out on the road it jumps and hops as if it were in 4wheel high or something.

Is it safe to drive a Ford Expedition without ABS?

Skidding tires also create flat spots in the tire, which can be inconvenient and dangerous in itself. ABS also allows you to be able to steer the vehicle while slowing down, and has been around for so long that many drivers have never driven a vehicle without it. Is it Safe to Drive Your Expedition ?

When does the ABS light come on on a Ford Expedition?

Your Ford Expedition ‘s ABS Light comes on when it fails a self diagnostic cycle. When on, it indicates that the Expedition does not have Anti-Lock brakes, and the safety they provide. Your Expedition ‘s ABS system uses a system of sensors to determine wheel speed when braking.

What does the brake light mean on a Ford Expedition?

The brake light indicates that there is a problem with the physical braking system and that your Expedition is unsafe to drive. Yes, you can drive your Expedition with the ABS light on. Is it safe? It’s not as safe, especially when it’s raining, snowing, or the road surface is loose/uneven.

How does the transmission work in a Ford Expedition?

The Powertrain Control Module (PCM) and its input/output network control the following transmission operations: Torque converter clutch operation. The transmission control is separate from the engine control strategy in the powertrain control module, although some of the input signals are shared.

What causes a Ford Expedition to stall at a stop?

Bad Solenoid. When your Ford Expedition stalls at a stop, just as it would if it had a manual transmission and you neglected to push in the clutch, that’s a sign that one of the solenoids is malfunctioning or has gone out.

Where is the 4×4 low range switch on a Ford Expedition?

The 4×4 low (4x4L) range switch is located on the transfer case cover. It provides an indication of when the 4×4 transfer case gear system is in the low range. The powertrain control module then modifies shift schedule for 4x4L operation.

The 4×4 low (4x4L) range switch is located on the transfer case cover. It provides an indication of when the 4×4 transfer case gear system is in the low range. The powertrain control module then modifies shift schedule for 4x4L operation.

The Powertrain Control Module (PCM) and its input/output network control the following transmission operations: Torque converter clutch operation. The transmission control is separate from the engine control strategy in the powertrain control module, although some of the input signals are shared.

Bad Solenoid. When your Ford Expedition stalls at a stop, just as it would if it had a manual transmission and you neglected to push in the clutch, that’s a sign that one of the solenoids is malfunctioning or has gone out.

What does overdrive cancel mode do on a Ford Expedition?

The powertrain control module energizes the transmission control indicator lamp (TCIL) when the switch is off. The TCIL indicates overdrive cancel mode activated (lamp on) and electronic pressure control (EPC) circuit shorted (lamp flashing) or monitored sensor failure.

When did the Ford Expedition go into production?

Styling approval was completed in early 1993 (3 1/2 years ahead of 1996 production) under design chief Bob Aikins, with the UN93 design being frozen by September 1993, at 34 months prior to July 1996 production commencement. The all-new full-size SUV was unveiled on May 9, 1996 and launched on October 2, 1996 as a 1997 model.

How many expeditions have been to the International Space Station?

Two decades ago, Expedition 1 arrived at the International Space Station to begin an unbroken chain of expeditions to inhabit this outpost. Over those 20 years, 64 expeditions have called the ISS their home.

What kind of interior does a Ford Expedition have?

Expedition featured an all-new front fascia, grille work, headlamps, body trim, rear fascia, tail lamps and liftgate. Interior fit and finish were improved with an all-new interior featuring new dash, door panels, genuine aluminium trim, and plush carpeting.

Styling approval was completed in early 1993 (3 1/2 years ahead of 1996 production) under design chief Bob Aikins, with the UN93 design being frozen by September 1993, at 34 months prior to July 1996 production commencement. The all-new full-size SUV was unveiled on May 9, 1996 and launched on October 2, 1996 as a 1997 model.

Expedition featured an all-new front fascia, grille work, headlamps, body trim, rear fascia, tail lamps and liftgate. Interior fit and finish were improved with an all-new interior featuring new dash, door panels, genuine aluminium trim, and plush carpeting.

How does the speedometer work on a Ford Expedition?

The programmable speedometer/odometer module (PSOM) receives input from the rear brake anti-lock sensor. After processing the signal, the PSOM relays it to the PCM and the speed control module.

Is there a factory alarm on a Ford Expedition?

While some erroneously call this system the factory alarm, it really is not an alarm system. The PATS system will arm itself if someone attempts to start the vehicle with anything other than the PATS key programmed to that specific vehicle.

How to troubleshoot the theft protection in a Ford Expedition?

Moore is a contributing writer for RF365.com and various other websites, a ghostwriter for Rainbow Writing and has over a dozen works of fiction currently in print. How to Troubleshoot the Ford Securilock …


Are there any electrical problems with my Eddie Bauer?

Judging from the amount of traffic on here I am not holding my breath, but I have had a 07 eddie bauer for about 1 month and a few very annoying electrical problems have been happening. First, A/c and fan cut out on a 100 degree day, turned the car off and on and problem fixed.

When did I buy an Eddie Bauer expidition?

I bought an 2003 Expidition Eddie bauer I worked fine in tell a week after we got it home.

Where is the fuse box on a Ford Expedition?

About us Contact us Ford Expedition (1997 – 2002) – fuse box diagram Posted on 28 July 2018by admin Ford Expedition (1997 – 2002) – fuse box diagram Year of production: 1997, 1998, 1999, 2000, 2001, 2002 Passenger compartment The fuse panel is located below and to the left of the steering wheel by the brake pedal.

What kind of engine does Ford Expedition have?

FORD EXPEDITION 2001 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD EXPEDITION 2001 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph. Whenever Vehicle Has Been Started And Running For A Minute It Would Suddenly Cut Off For No Reason.

What’s the speed of a 2001 Ford Expedition?

VEHICLE SPEED: 5 mph. DEALER’S NAME: DEAN STALLINGS FORD . While Placing The Key Inside Of The Ignition Vehicle Would Turn Off. But Consumer Could Turn The Ignition Switch Manually Without The Key Inside. Vehicle Would Turn On, And The Windows Would Roll Up.

Are there any problems with the 2001 Ford Expedition?

2001 Ford EXPEDITION Electrical System problems & defects. If you are driving a 2001 Ford EXPEDITION, or if you are planning to purchase one, then it is important that you review reported Electrical System problems and defects. Total reports: 73.

How often does Ford Expedition surge without gas?

While Engine Isideling, Vehicle Will Surge Foward Without The Drivers Foot On The Gas, This Has Occurred A Total Of Five Times.

FORD EXPEDITION 2001 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD EXPEDITION 2001 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph. Whenever Vehicle Has Been Started And Running For A Minute It Would Suddenly Cut Off For No Reason.

What’s the VIN number on a 2001 Ford Expedition?

Also My 4 Wheel Drive Kicks On Sometimes When Im Setting Still ,like At A Red Light.i Have To Turn It On Then Turn It Off For I To Get Out Of 4 Wheel Drive. *ak Vehicle Identification Number (VIN):1FMPU16L51L.

Since re-soldering all nine of the connector pins on the circuit board and cleaning the sloppy solders and rosin from the back of the board, I have driven 1000+miles with no problems whatsoever. This has clearly solved the problem. Hi I have a 01 Ford expedition and like everyone else I am having the same leak problems.

What causes the spark plug to go out on a Ford Expedition?

An additional 151 people reported an ignition coil failure caused by an excessive spark plug gap. This problem also causes the check engine warning light to illuminate. Repairs include replacing the ignition coils, spark plugs, and all coil boots. The issue affects a number of model years, lasting from 1997 to 2011.

What’s the difference between 2003 and 2004 Ford Expedition?

Though the 2003 model has the most complaints, the 2004 Ford Expedition tends to require more expensive repairs and has more issues that occur at lower mileage. Ford Problems reports these common Ford Expedition issues and some of the details that tend to surround them:

How much does it cost to repair a Ford Expedition?

According to them, repairs tend to average anywhere between $100 and $499. Here’s a closer look at the average distribution of costs for Ford Expedition repairs: Additional data from True Delta breaks down the average number of problems that Ford Expedition owners deal with based on the vehicle’s model year:

What kind of noise does Ford Expedition make?

Another ConsumerAffairs review mentions that they hear an extremely loud humming noise any time that they drive their Ford Expedition. They say that it’s so bad they are unable to hear other passengers in the car or even listen to the radio.

Where is the suction allowign exhaust in a Ford Expedition?

They seem strongest with the right rear window (located above the tail pipe) is rolled down, especially if a window on the opposite side of the car is also rolled down. This arrangement apparently reduces internal passenger cabin air pressure, creating a suction allowign exhaust to get in???

What should the gas mileage be on a Ford Expedition?

If you want the best gas mileage, you have to get the vehicle up to its top performance. Ideal gas mileage for a Ford Expedition is between 15-18 miles per gallon.

Where did the fire start in my 1997 Ford F-250?

After being parked for 4hrs.and unattended my 1997 Ford F-150 4X4 truck VIN.# [xxx] caught fire in engine compartment. Fire appears to have started in the area of the master cylinder. This was observed from the hole that was burnt in the hood on the left front of vehicle’s hood.

Author Image
Ruth Doyle