What does the p1260 Ford diagnostic trouble code mean?

P1260 FORD Meaning. The P1260 code can be set if the Passive Anti-Theft System (PATS) has determined a theft condition existed and the engine is disabled or an engine start was attempted using a non-PATS key. This Diagnostic Trouble Code (DTC) is a good indicator to check the PATS for DTCs.

When does PATs set the error code p1260?

Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model to another. Error Code P1260 is set when the PATS (Passive Anti-Theft System) have determined a theft condition in the system which disabled the engine, or the engine will not start from a non-PATs key attempt.

How much does it cost to repair a Ford p1260?

Check for damaged components and look for broken, bent, pushed out, or corroded terminals. The cost of diagnosing the P1260 FORD code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

What was the p1260 code on my Saab 93?

I have a 2002 Saab 93, it kept getting code P0101 and P1260, 1251. Dealer said it was a bad throttle body-ie traction controll. I had throttle body rebuilt. Cleared codes, reset throttle body. it was fine for 15 miles now check engine light is on again and traction controll light also Codes P010…

What happens if you have an incorrect ignition code?

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

How often should you insert and remove the ignition key?

You may insert and remove the ignition key thousands of times every year, wearing the key and tumblers ever-so-slightly every time. Heavy keychains can add more stress to the ignition cylinder, increasing wear. After a while, the key may fall out of the cylinder or be unable to turn out of the lock position.

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

When do you set the p1260 theft code?

Most auto repair shops charge between $75 and $150 per hour. When is the code detected? The P1260 code can be set if the Passive Anti-Theft System (PATS) has determined a theft condition existed and the engine is disabled or an engine start was attempted using a non-PATS key.

What does p1260 stand for in Pats?

P1260 indicates that the Passive Anti Theft system (PATS) detected a “theft condition”. This basically means an incorrect signal, or no signal at all was received from the chipped key.

Why does my Pats p1260 have a blinking theft light?

This is mostly caused because I have a bad transponder in both ignition keys (wouldn’t start with both factory keys), a bad transceiver ring in the column/ignition switch, or a bad diode in the PCM. Blinking Theft light. It’s also can be caused by a few other issues that I’m fully aware of at this time.

How much does it cost to repair a p1260 Ford?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1260 FORD code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

What does the p1260 diagnostic trouble code mean?

P1260 Meaning. The P1260 code can be set if the Passive Anti-Theft System (PATS) has determined a theft condition existed and the engine is disabled or an engine start was attempted using a non-PATS key. This Diagnostic Trouble Code (DTC) is a good indicator to check the PATS for DTCs.

What does it cost to set a p1260 code on a car?

The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. The P1260 code can be set if the Passive Anti-Theft System (PATS) has determined a theft condition existed and the engine is disabled or an engine start was attempted using a non-PATS key.

How can I Reset my Ford p1260 code?

The first thing to do in this instance is retrieve codes from the PATS module and diagnose these. Once the PATS issues have been resolved you can reset the P1260. Communication with the PATS module will likely need to be done at a Ford dealer.

When to set DTC on a Ford p1260?

This DTC can also be set when a new Instrument Cluster (IC), Instrument Panel Cluster (IPC) or Powertrain Control Module ( PCM) is installed without correctly programming either module even if the vehicle is not equipped with PATS. Need more information on how to fix the P1260 FORD code?

What does the p1260 Ford diagnostic trouble code mean?