How can I disable the pass lock system?

•Avoid Costly repairs for an already broken PassLock System. •Disable Pass Lock system to prevent from being stranded in the future. This tutorial varies depending if the ignition is located: If your ignition is located in the dash then you will be removing the panels on the passenger underside (toe board) of the dash.

Can You disable the PassLock on a GM car?

The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.

How long does it take for PassLock sensor to turn off?

•Observe the security light located in the instrument cluster, after approximately 10 minutes the security light will turn OFF. Turn OFF the ignition, and wait 5 seconds. •The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.

How big is resistor on GM PassLock system?

If you can’t find something anywhere near to what you read on the ohm meter you have the option to use a resistor between 0.5K ohms up to 13.6K ohms.

What is the key OK signal for the vats bypass module?

The VATS bypass module generates the ‘key ok’ signal normally sent from the BCM to the PCM (Powertrain Control Module) or ECM (Engine Control Module). VATS bypass module wires: RED: 12V ignition of accessories WHITE: Fuel Enable wire. 50hz or 30hz. BLUE/GREEN: Control wire.

Is there a way to bypass GM PassLock?

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

What is the PASSKey System on a GM car?

Some GM vehicles come with a factory-installed anti-theft system commonly referred to as the passlock or passkey. Due to glitches with these built-in security systems, GM owners may experience problems trying to start their vehicles.

How can I disable the passkey anti-theft system?

You can swiftly disable the passkey anti-theft system and get your GM started by performing the “relearn” procedure, which disables the passkey by resetting it. Insert your GM key into the ignition, attempt to start the car, and let it stall. After it stalls, leave the key in the starter in the “On” position.

How to bypass vats, Passkey and PassLock security systems in GM?

It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.

Is there a way to disable PassLock and VAT?

This can also be done using this Bypass (this is what is done on my 2007 Cobalt ss/sc for the remote start/alarm). Thanks for the how to but with an HPtuners you can disable it with out going through all that. yep, this is more for people that can’t disable passlock or vats because they dont have access to hpt.

How do you reset anti theft?

2 Answers. Re: Resetting the anti theft system. Place key in ignition, turn to ON position. (do not start) Leave in ON position for EXACTLY 10 minutes. As SOON as the anti-theft light turns off, then IMMEDIATELY start the car. Then anti-theft is now reset.

How do you bypass security system?

1. With the system in the disarmed, select the “Zones” icon. The system will display the list of zones. 2. Select the zone(s) you want to bypass and select “Bypass”. 3. Enter your master alarm code. The system will return to the Bypass screen and the zone(s) that are bypassed will be displayed.

How does PassLock system work?

The PassLock system works when the lock cylinder moves a magnet past a Hall effect sensor . The sensor then sends a signal to the control, which GM has moved several times over the model years. The control then sends the code to the PCM. If the code is correct, the PCM will allow the car to start and run.

What is a PassLock system?

The Passlock system is part of the factory anti-theft system. Basically what it does is if your car alarm is activated or if someone tries to start your car using a different key or a flat head screw driver it disables fuel to the engine.

What to do if your car won’t start at PassLock?

A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down. A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off.

What to do if your PassLock is locked?

Instead concentrate on basic instructions and you will be able to start your journey again without much delay and hassle. Turn on the ignition key and leave it at ‘ON’ position, after the vehicle stalls. This is to turn on the PassLock security system to see if it is locked.

How to permanently disable the PassLock II system?

Try restarting it, you will see the red security light on, but that can be removed with the LED mod how to. This can also be done using this Bypass (this is what is done on my 2007 Cobalt ss/sc for the remote start/alarm). Thanks for the how to but with an HPtuners you can disable it with out going through all that.

How do I Turn Off the PassLock sensor?

•The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK. The vehicle learns the Passlock Sensor Data Code and/or resistance on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.

What kind of remote do I need for PassLock?

I had a compu star remote started put in the truck 2 years ago, I have a 2005 GMC Canyon Vortec 3500, and just recently the trucks passlock is acting up like every week! Leaving me stranded for the 5-10 min thing. posting.php?mode=reply&f=8&t=84432#