What axle does my F150 have?

Open the front door on the driver’s side. Locate the Truck Safety Compliance Certification Label on the door pillar near the door latch. Locate the two-digit code in the box labeled “AXLE,” which is just below the bar code. Match the code on the label to the corresponding rear axle ratio.

What axle does Ford use?

The Sterling 10.5 axle is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI. It was first used in model year 1985 Ford trucks. The axle was developed to replace the Dana 60 and Dana 70.

What is the best axle ratio for a Ford F150?

Axle Ratio When choosing your F-150, knowing that a 3.73 ratio provides much more towing power than a 3.55 or 3.31 ratio is crucial to achieving the capability you desire. Basically, the higher the ratio is, the more power you will get from your engine. Conversely, a higher ratio will lower a truck’s fuel efficiency.

What kind of suspension does a Ford Bronco have?

In 1980 the Bronco went from a straight Dana 44 front axle to what Ford calls the Twin Traction Beam (TTB) front suspension. The TTB system is Fords version of an independent front suspension, and was used on the Ford Bronco from 1980-1996.

What kind of axle does a Bronco use?

This system will utilize an 05-16 Ford Super duty Dana 60 axle and performance coil over shocks. The kit will provide 4 to 8″ of lift giving your vehicle much better ground clearance for rock crawling and trail applications.

What kind of truck was the Ford Bronco in 1980?

1980 Ford Bron. Broncos and F-Series pickups got a new face for 1980, and pickup trucks continued to offer both Styleside and Flareside beds. 1980 Ford Ranger. Bronco and F-Series four-wheel-drive truck models adopted Twin-Traction Beam independent front suspension for 1980.

How much does a stock Bronco front drivehaft cost?

Note: Stock Bronco front driveshaft can be utilized by using our conversion U-joint, however applications lifted 8″ or higher may need a custom drive line or transfer case indexing ring/cross member modification. We have sources for axles depending on the year and condition that range from $1500-$2000 for both.

What kind of axle does a Ford Bronco use?

The Dana 44 TTB (Twin Traction Beam) was used in the front of Ford F-150’s and Ford Bronco’s from 1980-1996. Production on the Ford Bronco completely ceased after 1996, and the Ford F-150 switched from the Dana 44 TTB to an 8.8 IFS front axle in 1997. The Dana 44 TTB was a variation of the reverse cut solid axle Dana 44 used by Ford.

When did Ford stop making the Ford Bronco?

Production on the Ford Bronco completely ceased after 1996, and the Ford F-150 switched from the Dana 44 TTB to an 8.8 IFS front axle in 1997. The Dana 44 TTB was a variation of the reverse cut solid axle Dana 44 used by Ford. It appeared in the F-150’s and Bronco’s with coil springs.

What was the name of the 1987 Ford Bronco?

On the engineering side, new powertrain and safety updates took center stage. Affectionately known in enthusiast circles as the “brick nose,” the 1987 Bronco boasted a more aerodynamic silhouette than its “bull nose” predecessors.

In 1980 the Bronco went from a straight Dana 44 front axle to what Ford calls the Twin Traction Beam front suspension. The TTB system is Ford’s 1980-1996 version of an independent front suspension.

What axle does my f150 have?

Open the front door on the driver’s side. Locate the Truck Safety Compliance Certification Label on the door pillar near the door latch. Locate the two-digit code in the box labeled “AXLE,” which is just below the bar code. Match the code on the label to the corresponding rear axle ratio.

What is the Ford Axle code for 1991?

Ford Axle Code Chart. Axle Decoder Chart Code Ratio Capacity Maker Type Yr 12 2.73 3800 FORD REG 1991 17 3.25 3300 FORD REG 1971 17 3.31 3800 FORD REG 1995 18 3.08 3800 FORD REG 1991 19 3.55 3800 FORD REG 1991 25 4.10.

What is the Axle code for a 2008 Ford truck?

2008 Ford Super Duty Axle Codes: 35 = 3.55 non-limited slip 3J = 3.55 limited slip 37 = 3.73 non-limited slip

How do I identify the limited slip rear axles of a Ford?

Limited-slip axles transfer power to both wheels, yet allow the wheels to turn at different speeds when turning corners. Determining what type of limited-slip rear axle a Ford F-150 has can be accomplished two ways. After 1968, Ford cars and trucks have an axle code on a “Certification Plate,” located on the driver’s door.

What kind of rear axle does a Ford F-150 have?

Rear axles come in two flavors, “open” and “limited-slip.”. The open rear axle only provides power to one rear wheel. Limited-slip axles transfer power to both wheels, yet allow the wheels to turn at different speeds when turning corners. Determining what type of limited-slip rear axle a Ford F-150 has can be accomplished two ways.

Where is the Axle code on a Ford truck?

After 1968, Ford cars and trucks have an axle code on a “Certification Plate,” located on the driver’s door. Ford rear axles also have an identification tag located on the rear axle itself.

Limited-slip axles transfer power to both wheels, yet allow the wheels to turn at different speeds when turning corners. Determining what type of limited-slip rear axle a Ford F-150 has can be accomplished two ways. After 1968, Ford cars and trucks have an axle code on a “Certification Plate,” located on the driver’s door.

How can you tell the axle ratio of a Ford truck?

There’s no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you’ll see a sticker like the one shown below:

Rear axles come in two flavors, “open” and “limited-slip.”. The open rear axle only provides power to one rear wheel. Limited-slip axles transfer power to both wheels, yet allow the wheels to turn at different speeds when turning corners. Determining what type of limited-slip rear axle a Ford F-150 has can be accomplished two ways.