Can a Ford F-150 blend door actuator be replaced?

For the last 20 or 30 years in these trucks, they have been prone to failure. I love my truck, but I wish Ford had fixed this problem by now. On the plus side, where older generations required disassembling the dash to fix, the 2009-2014 generation’s most common problem can be fixed with the dash left in place.

Where is the blend door on an F-150?

The blend door is actually behind the radio, so the first step is to get the radio out. The silver panels on each side of the radio simply pull straight out as pictured. This panel will pull entirely out, if you lift up just slightly on the other paneling it is caught behind.

What do you need to replace blend door actuator?

You need an 8mm box wrench, along with a 7mm or equivalent SAE socket and socket wrench. I used a paint can opener to help pull the plastic off. The blend door is actually behind the radio, so the first step is to get the radio out. The silver panels on each side of the radio simply pull straight out as pictured.

Where is the passenger door actuator located on a Ford F150?

The one that controls the passenger temp is located on top of the hvac unit behind the radio. The one that controls the defrost, foot,dashvents is located on the drivers side up under the dash (it sits right next to the accelerator you can get this one without dismantling the dash).

How do you replace a blend door on a Ford truck?

While a dealer will remove the dash, evacuate the A/C and drain the heater, you can simply remove the glove box by squeezing the side in, releasing the tabs, and pulling down and out. Figure 1. Remove the glove box. Pull and pry the three squeeze-clips (or remove the 5/16 screws) to remove the actuator.

What happens when you replace the actuator on a blend door?

Once all of the mounting screws have been removed the actuator should become loose. Grasp the actuator and pull it from its mount to remove. Before installing the new actuator it’s a good idea to manually turn the blend door in both directions to ensure it is not stuck which will cause the new actuator to fail.

How to replace an automotive blend door actuator?

Before installing the new actuator it’s a good idea to manually turn the blend door in both directions to ensure it is not stuck which will cause the new actuator to fail. Grasp the door pivot and move it back and forth to its full travel, it should move freely.

Can a 2009-2014 door actuator be replaced?

Where is the fuse number on blend door actuator?

EDIT: From everything you have said and my experience (I’ve replaced it twice within the last year, first time with aftermarket and again with OEM) you are doing everything right except for the fuse number. There is another actuator in the drivers footwell that controls the hvac mode door (which vent the air comes from).

What does the blend door do on a Ford F-150?

A Ford F-150’s blend door is the device that controls how much heat or AC comes through the HVAC system. For the last 20 or 30 years in these trucks, they have been prone to failure. I love my truck, but I wish Ford had fixed this problem by now.

Where is the actuator located on a F-150?

The first screw is easy to remove. It’s sitting right in front, easily accessible. The rear screw requires going through the glove box. To get to the rear screw, you lower the glove box, pinch the sides, and then lower it further. That keeps it nice and out of the way. Then, you can reach up through the glove box to the actuator area.

Why does my F-150 blow cold air?

This F-150 would only blow cold air because the actuator for the blower door went out. Before I went this far to replace the part I started a few diagnoses: tested the air conditioner, went under the hood to see if the heater core hoses were hot, and check the internet if this was a common issue. Sure enough, every test lead to a faulty actuator.

When to pull fuse 15 on blend door actuator?

Roasting in Florida. Video Player is loading. This is a modal window. Beginning of dialog window. Escape will cancel and close the window. End of dialog window. Fuse 15 was for 2009-2010 trucks. On your 2012 you’re going to want to pull fuse 46 in the same smart junction box. Should be labeled climate control in your manual.

Where is the defrost actuator on a F150 FX2?

Then there is the Defrost/Panel/Floor Door Mode Door Actuator mounted on the drivers side of the evaporator case which is mounted under the drivers side of the dash. Unplug them on at a time and see if it goes away. Ask Your Own Ford Question Customerreply replied 3 years ago I will try that. Do i need to take everything apart again?

How much does it cost to replace a blend door actuator?

If that happens, the blend door won’t work, and it’s likely your temperature will just be stuck on one setting with no ability to adjust the intensity up and down, or alternate between things like the lower vents or the defroster. The cost of replacing a blend door actuator is typically between $300 and $400.

What happens to the blend door on a Ford F-150?

This article applies to the Ford F-150 (2004-2014). The blend door mixes the hot air with the cold air in the cabin of your Ford truck. If the door is broken, sometimes only hot air will blow through the vents, or similarly, just cold air.

Why is my F-150 heat and AC door popping?

2011 F-150 heat/ac blend door is popping. Can I reset it by… I have a 2014 flex limited AWD ECO. I replaced the blend air I have a 2014 flex limited AWD ECO. I replaced the blend air controller on the driver side. Nothing seemed to change (no AC on driver side) Do I … read more Subaru and Nissan factory t…

What should I do if my F-150 heat / AC door is popping?

2011 F150 heat/ac blend door is popping. Can I reset it by removing the #15 fuse for 30 sec. and then reinstalling and 2011 F-150 heat/ac blend door is popping. Can I reset it by…

Is the power door lock on my F150 working?

– Ford F150 Forum – Community of Ford Truck Fans Power door lock actuator doesn’t work. Power door lock actuator doesn’t work. Door lock actuator doesn’t work. Driver side rear door. New actuator doesn’t work either. Didn’t bolt it in but I tested it before removing the existing actuator.

When to replace actuators on Ford F-150?

Save some cash and replace your actuators yourself after reading our guide below. This article applies to the Ford F-150 (2004-2014) and the F-250, F-350 Super Duty (2005-2014). The actuators are what engage your front wheels to the transfer case. Overtime the gears inside can wear down causing the front wheels to not lock in.

Why did my F-150 blend door actuator go out?

If you switch it towards heat a little bit, and the noise stops, your F-150 blend door actuator has gone out. A common issue in these trucks is the failure of the potentiometer that senses when the actuator has turned fully.

How do you reset the blend door actuator?

Remove the floor air outlet duct extension (1) from the floor duct (2). Disconnect the electrical connection at the blend door actuator (#10 in pic below). Remove the blend door actuator mounting screws from the HVAC module. Remove the blend door actuator as an assembly with the actuator cam.

Where are the actuators on a Ford F-250?

Those systems will have a single top-mounted actuator behind the radio. Automatic Temperature Control-equipped dual zone trucks have two; the second actuator is low, located above the transverse air duct. Does the temperature controller work?

What does the blend door actuator do on a F-250?

The blend door actuator is responsible for controlling the hot and cold air mixtures in your Ford F-250 or F-350 Super Duty.

Can you replace the blend door on a Ford F-150?

How much does it cost to replace an F-150 blend door actuator?

The replacement actuator, available here online or at a local Autozone, costs between $20 and $35. You’ll know you need to perform this procedure if you hear a loud, persistent POP noise whenever you switch your HVAC to “full cold”. If you switch it towards heat a little bit, and the noise stops, your F-150 blend door actuator has gone out.

Where is the blend door actuator on my Ford Explorer?

The problem comes in where the manufacturer places it. In my 2003 explorer they placed it in such a location where the entire dash has to be partially removed, then loosened up to unscrew three screws to replace the part. Ford definitely didn’t have a better idea here.

Is there a problem with my Blender actuator?

Knocking: This is an unusual symptom, but if you’re experiencing this, it’s almost definitely a problem with your blender actuator. When you start the car, or just the AC system, and notice a knocking sound like someone tapping on your door, that is indicative of a problem with the blend door actuator.

Is the blend air door broken on a 1999 Ford F150?

I had already determined that the blend air door was broken in this 1999 Ford F150. There are some hacked up ways of changing this door and if that is what you are looking for this article is not for you.

How to turn a blend door on and off?

Insert actuator shaft into A/C air temperature control door and secure A/C electronic blend door actuator to A/C evaporator housing with four retaining screws. Install electrical connector to bracket on A/C electronic blend door actuator. Install instrument panel insulator and console panel if equipped. Connect battery ground cable.

How to manually turn a blend door actuator?

Install electrical connector to bracket on A/C electronic blend door actuator. Install instrument panel insulator and console panel if equipped. Connect battery ground cable. Thanks for instruction.

How much does it cost to replace HVAC actuator?

Truthfully, the work isn’t really that bad. The replacement actuator, available here online or at a local Autozone, costs between $20 and $35. You’ll know you need to perform this procedure if you hear a loud, persistent POP noise whenever you switch your HVAC to “full cold”.

How much does it cost to replace actuator on F-150?

On the plus side, where older generations required disassembling the dash to fix, the 2009-2014 generation’s most common problem can be fixed with the dash left in place. Truthfully, the work isn’t really that bad. The replacement actuator, available here online or at a local Autozone, costs between $20 and $35.

How does blend door actuator work on F150?

Blend control valve only turns counter clockwise, when actuator is off the valve it does about a full revolution when key goes in the ignition. The … read more 2009 f150 fx4 duel zone climate control. No heat drivers 2009 f150 fx4 duel zone climate control. No heat drivers side. removed dash replaced blend door damper.

How do you replace rear door actuator on F-150?

The rear screw requires going through the glove box. To get to the rear screw, you lower the glove box, pinch the sides, and then lower it further. That keeps it nice and out of the way. Then, you can reach up through the glove box to the actuator area. You’ll need to use an 8mm box wrench.

How does the blend control valve work on a F150?

Vocational, Technical or Tra… Blend control valve only turns counter clockwise, when actuator is off the valve it does about a full revolution when key goes in the ignition. The … read more 2009 f150 fx4 duel zone climate control. No heat drivers 2009 f150 fx4 duel zone climate control.

What is the part number for the blend door actuator?

The part number on my ’06 Fusion for the blend door actuator is 6E5H-19E616-BA, but when I looked the part up on the 2010’s the prefix was AE5H-19E616-BB, so maybe its a good idea to check your part numbers before you buy the replacement. Its easy to see once you are underneath the dash looking up. (The pics below will help)

What should I do about my blend door actuator?

This answer was rated: Just replaced blend door actuator on 2011 impala and its… Just replaced blend door… Just replaced blend door actuator on 2011 impala and its still clicking when it tries to recalibrate…. it appears that it is not recognizing its limits and just keeps moving thus jumping gears. dont have scan tool so what do I do?

How much does it cost to replace door actuator on Ford Edge?

The average cost for a Ford Edge HVAC blend door actuator replacement is between $151 and $164. Labor costs are estimated between $51 and $64 while parts are priced at $100. This range does not include taxes and fees, and does not factor in your specific model year or unique location.

How to test Ford heater blend door actuator?

How to test Ford heater blend door actuator. The Ford shop manual shows several ways to test the blend door actuator. Jumper the motor connections at the actuator with fused battery voltage to move the motor. Test for + and – on each actuator connector coming from the HVAC controller.

How long does it take to calibrate blend door actuators?

To carry out calibration, carry out the following steps. Remove BCM fuse 46 for at least one minute. NOTE: When the ignition switch is switched to the ON position, the HVAC module will initialize and calibrate the actuators. Calibration of the actuators will take approximately 30 seconds.

What causes a blend door actuator to fail?

If you cannot move the blend door an obstruction has gotten in the way of the door movement which will make the new actuator fail. These obstructions can include: pen, tooth pick, small toy or bubble gum to name a few. If the door is stuck the heater plenum with need to be removed and the problem resolved before installing the new unit.

Is the actuator on my Ford F150 still working?

I replaced the blend door actuator two times and it still doesn’t work. The First time was with an aftermarket actuator, second time with an OEM from my local Ford dealer and it’s still clicking on my 2012 XLT. I also lifted the battery connection for the actuator calibration.

How old is the Ford F-250 Super Duty?

I’ve owned 2 F-150’s the 5.4 and whatever the V6 is the 5.4 was a gem I loved it until a 16 year old T-Boned me at 60mph and that’s what it took to kill it. The V6 for how bad I beat the snot out of it still runs like a champ.

Is the 2006 Ford F-250 Super Duty 4WD?

Description: Used 2006 Ford F-250 Super Duty Lariat with AWD/4WD, Rear Bench Seats, Audio and cruise controls on steering wheel, Auto Climate Control, Power Driver Seat. 2006 Ford F-250SD LariatClean CARFAX.

Is the Ford company still under family control?

While Henry Ford has long passed, the company is still under family control, which is quite the feat. The company has certainly gone through its share of rough patches, but it continues to be a staple and a leader in the automotive industry.

When did Henry Ford Start the Ford Motor Company?

When one thinks about automobiles and their history, it is impossible not to think about the Ford Motor Company as well. Henry Ford founded the company in 1903 in Detroit, Michigan. While he did not invent the car, at the turn of the 20th century the automobile was merely a luxury toy for the rich.

Can a Ford F-150 blend door actuator be replaced?