How to change rear brake pads on Dodge Ram 2500?

This is a step by step instructional video on how to change the rear brake pads on a Dodge Ram Pickup 2500 Heavy Duty. It covers the beginning to the end of the project including tire removal, caliper piston compression, replacement of disc brake pads and bleeding of the brake lines.

Why are my brakes not working on my Dodge Ram?

Broke the line lose at the block behind the driver side rear wheel and nothing. Did the same at the front and still nothing. I get a gravity flow for the front at the control module and wheels but nothing for the rear.

What kind of brakes does a Dodge Ram have?

Discussion in ‘ Exterior ‘ started by Mr78, Jul 23, 2017 . I have a 2005,2500, with the 5.7. I had a rear caliber blow a few days ago, and just had time to change it today.

Where does the brake line run on a Dodge Ram?

The line runs a crossed the rear axle an ties into the line on the drivers side. No fluid there so I went to the front on the truck where the line runs along the frame before it goes into the abs control module.

How do you remove the brake caliper on a Dodge Ram?

Wash down the brakes with brake cleaner. The brake caliper is held onto the brake caliper bracket by two bolts located on the backside of the caliper. Loosening these bolts will allow you to remove the brake caliper by sliding it up and out of the way.

Why do I need to replace my brake line on my Dodge Ram?

Through the life of your Dodge Ram, it is possible you may need to replace the brake lines. This could happen due to damage or possibly even due to corrosion. In some wet or colder climates, especially where it snows, this is a very common issue.

Your Dodge Ram’s brakes tend to work a little harder than most average vehicles. You want to make sure the brakes are fresh so it can keep working just as hard. This article applies to the Dodge Ram (2002-2008). The brakes on your Dodge Ram tend to take quite a beating.

What kind of brakes does a Ram 2500 have?

The factory calipers are pretty large and apply a good amount of force. There is no denying that the calipers on our ’06 Ram 2500 are good. They are two piston calipers. Both pistons are on the same side of the caliper. As the brakes are applied, the pistons push against the inside brake pad.

How does brake fluid move in Ram 2500?

As you apply the brake pedal, there is a plunger in the master cylinder that is moving fluid from the reservoir into the brake lines. The more fluid that is pressed into the brake lines, the more pressure in the brake lines. As the brake lines start to increase in pressure, the pistons inside of the caliper starts to move.

How to replace brake master cylinder in Dodge Ram?

Tighten the nuts to the booster first. Just before you hook the metal lines up, remove the plastic bleeder and quickly attach the metal line. Tighten each metal line with your tubing wrench securely.

How do you replace brake pads on a Dodge Ram?

Most new pads come with new anti-rattle clips. Either way, if you keep or replace them, you will want to apply some grease to them to help the pads slide easily in them. Figure 8. Remove the brake pads. Figure 9. Apply grease to the anti-rattle clips. Now that you have the pads and caliper removed and out of the way, you can remove the brake rotor.

How do you change the rotor on a Dodge Ram 1500?

Remove these two bolts and lift off the bracket. The rotor should easily slide off the lug bolts, just as if a tire was being changed. Occasionally it will be rusted in place and need to be tapped with a hammer; be careful not to damage the lug bolts. Slide the new rotor into place and replace the caliper mounting bracket.

How do you change the brake fluid on a Dodge Ram 1500?

Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir. Check periodically to make sure it is not running over. If needed, a clean rag can be inserted into the reservoir soaking up some of the fluid and remove it.

How do you remove the caliper from a Dodge Ram?

To completely remove the caliper, you will need to loosen the banjo bolt that secures the rubber brake line to the caliper (Figure 7). This will be the only thing keeping it attached to the vehicle at this time. When you loosen this bolt, brake fluid will leak out, so be prepared to catch it with a suitable container.

When to replace the emergency brake on a Dodge Ram?

This article applies to the Dodge Ram (1994-2001). It can oftentimes be over looked, but the emergency brake will need to be serviced at some time during the life of your truck just like the rest of the brake system. The emergency brake has two major functions.

Where are the brake shoes on a Dodge Ram?

So, on a drum-brake-equipped truck, replacing the emergency brake is a matter of replacing the rear brake shoes. The emergency brake on a disc-brake-equipped truck works with shoes located inside of the rear brake rotors.

What should torque be on new brake pads?

Torque to 38 ft/lbs. After installing new pads on the front axle, several pumps of the brake pedal will be required to move the caliper pistons into position and restore proper brake pedal travel.

When do I need to replace my brake pads?

You should follow the manufacturer’s recommended minimum brake pad thickness. In most cases, you’ll want to replace brake pads when they get down to about 3mm. While you can sometimes get away with 2mm, that is right around where the metal wear indicator gets exposed and causes a squealing sound against the disc.

What causes a car’s brake disc to rotate?

There is also a spinning disc that rotates along with the wheel when the vehicle is moving. The caliper applies pressure to the brake pad, causing the pad to push against the brake disc. The friction created between the brake pad and brake disc causes the wheel to slow down its rotation.

What should the thickness of the brake pads be?

Therefore, anywhere from 3mm to 4mm is the recommended thickness to replace brake pads in most cases. You may be able to get away with slightly less thickness, but certainly nothing less than 2mm.

Are there disc brakes on 2nd generation Dodge Ram?

The rear brakes on the 2nd Generation Ram are of a drum design and are a bit more complex than contemporary disc brakes. Servicing of brake drums can be overwhelming for some, but do no fret as you can disassemble one drum assembly at a time while using the other as a guide.

Where was the 1999 Dodge Ram 2500 purchased?

Purchased on 05/12/99 and owned in WA until 05/21/21. Driven an estimated 7,827 miles/year. Last serviced at 172,231 miles in Woodland, WA on 05/04/21 • Vehicle serviced • Oil and filter changed. Mileage: 172,531 miles Body Type: Pickup Color: Burgundy Engine: 8 Cyl 5.9 L

Are there any Dorman drum brake backing plates?

Dorman 13867 HELP! Brake Backing Plate . Only 17 left in stock – order soon. . . Only 19 left in stock (more on the way). . . Only 5 left in stock – order soon. APDTY 24978 Brake Backing Plate- 1992-78 Models W/ 9-1/2In. Drum Brakes.

Is there a rear disc brake conversion kit for Dodge Ram?

EGR Rear Disc Conversion Kits for Dodge Ram, 94-01.5 2500 Single Wheel. Comes with easy to find brake pads. Most auto part stores stock them, it is a popular automotive application in most cases. You do not have to order them from us in the future unless you want the better Carbon-Kevlar friction material.

When is prime day for Dodge Ram pads?

Prime Day is June 21 & 22 1-16 of over 4,000 results for”dodge ram 2500 brake pads” Filter results by your vehicle: Enter a new vehicle to add it to Your Garage and filter the results below Enter a new vehicle

How do you Bleed the brakes on a Dodge Ram?

Have your helper sit in the driver’s seat of the vehicle, pump the brake pedal three times and then hold it down. Place the appropriate size socket on the bleeder screw located on the top of the brake caliper, and turn it counter-clockwise a quarter turn; this will release brake fluid and any air that is present.

Where does a leaking brake caliper go on a Dodge Ram?

A leaking brake caliper is easily spotted since the caliper body is exposed inside of the wheel and will be wet with fluid. A severely leaking wheel cylinder on the rear drum brakes will often leave a wet puddle down the rear side of the backing plate, or the bottom of the brake drum.

Why are the brakes on my Dodge Ram so bad?

The brakes on your Dodge Ram tend to take quite a beating. This is in part due to the fact that trucks usually work a bit more than most other vehicles. They are also usually used a bit harder and rougher than most other vehicles.

Do you have to change rear brake pads at the same time?

This applies to the rear as well, if you change the rear pads, both sides must be changed at the same time. Failure to do this could result in uneven braking, which could lead to loss of control or poor braking. Loosen the lug nuts on the wheels before jacking up the truck.

Do you need brakes for a Dodge Ram?

A vehicle as tough as your Dodge Ram needs heavy-duty stopping power. The brake pads provide most of the stopping power for your vehicle, so making sure you have the best brakes in the industry is a must.

When did the Dodge Ram 2500 come on the market?

No accident or damage reported to CARFAX. 1st owner purchased on 09/08/99 and owned in NE until 11/19/18 • 2nd owner purchased on 12/03/18 and owned in WY until 04/14/21. 1st owner drove an estimated 3,899 miles/year • 2nd owner drove an estimated 8,399 miles/year.

Do you need to change brake pads on a 4 wheel drive truck?

A four wheel drive truck is not discussed; the biggest difference will be that the hub must be removed to change the rotors. A new set of brake pads does not require this, and procedures will be the same for 2 or 4 wheel drive.

How do you replace disc pads on Dodge Ram 1500?

Remove the disc pads from the rotor. There is a small clip at the top and bottom of the opening where the pads came out; remove them. If the rotors are in good shape and are not to be replaced, clean the clips, lubricate them with brake grease and refit them into the place they came from. Replace the pads with new ones.

What are the best brake pads for a Dodge Ram 1500?

The best brake pads for Dodge Ram 1500 will be the ones that give you precise stopping control even when you are towing the heaviest loads. Your truck feels best when it’s operating at full capacity, and it can only do that when you have the stopping power you need under every circumstance.

How do you change the brakes on a Dodge Ram?

Remove the drum. There is a small hole in the backing plate that allows for adjustment of brakes via a star wheel. Using a screwdriver or brake adjusting tool, spin the star wheel enough to loosen tension of the brake shoes on the drum and remove the drum.

Where was the 2002 Dodge Ram 3500 last serviced?

1st owner drove an estimated 11,359 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 0 miles/year. Last serviced at 201,955 miles in Renton, WA on 06/16/20 • Vehicle serviced • Engine checked. Mileage: 204,644 miles Body Type: Pickup Color: Silver Engine: 6 Cyl 5.9 L Minor to moderate damage.

Where can I buy 2006 Dodge Ram parts?

OEM Dodge parts are manufactured by Dodge to maximize the performance of Dodge Ram 1500 vehicles and provide the certainty that the repair will be done right the first time. Parts that fit. Parts that perform. OEM Dodge Ram 1500 Parts. Genuine 2006 Dodge Ram 1500 Parts from Factory Chrysler Parts in Bartow, Fl. Buy OEM 2006 Ram 1500 Truck Parts.

Are there brake lines for the Dodge Ram 1500?

We offer a full selection of genuine Dodge Ram 1500 Brake Lines, engineered specifically to restore factory performance. Please narrow the Brake Line results by selecting the vehicle.

What kind of rear axle does a Dodge Ram 1500 have?

This is an original used OEM Rear Axle Assembly that’s guaranteed to fit a 2008 Dodge RAM 1500 with the applicable vehicle manufacturer’s specifications (). 4X2; EXC. MEGA CAB; 3.55 RATIO, Without ELECTRONIC STABILITY CONTROL We offer an industry leading 1-year warranty on every part type we sell.

How do you replace the front brake caliper?

With the front brake caliper removed from the steering knuckle (see Step 2), remove the brake line from the caliper using a 3/8″ combination wrench or socket. Figure 8. Brake line removal. Install the the brake line into the new brake caliper.

Are there rear disc conversion kits for Dodge Ram?

EGR Rear Disc Conversion Kits for Dodge Ram, 94-99 3500 Dual Rear Wheel. Comes with easy to find brake pads. Most auto part stores stock them, it is a popular automotive application in most cases.

Which is the best rear disc brake conversion kit?

EGR Performance Brakes offers a New Rear Disc Brake Conversion Kits for all Dodge Models. The complete bolt on kit is an easly bolt on kit.! Now get Superior Braking Performance & Heat Control, Faster & Shorter Stops and Increased Front Brake Life. Get Improved Brake Performance like the new trucks experience!

What kind of rear differential does Dodge Ram have?

Be aware that some trucks have add-on options that will dictate a different rear differential than what’s called out in the owner’s manual. For example, in 2005 there was a 3.21 non-limited-slip differential (LSD) axle ratio rear end for 2WD use and a 3.55 axle ratio rear end.

What kind of truck is a 2003 Dodge Ram?

Description: Used 2003 Dodge Ram Pickup 1500 SLT with AWD/4WD, Rear Bench Seats, Audio and cruise controls on steering wheel, 8000lb Towing Capacity, 6ft Bed. Good Deal! 2003 Dodge Ram 1500 4dr. Quad Cab SLT 4WD. SB Color:Red 170.000 miles This truck is a sharp looking ride Sale price $5,995 Call (207)754-0929 or (207)783-3336 Thank you

Where was the 2002 Dodge Ram 1500 built?

The 2002-03 Ram was available in regular cab and Quad Cab styles. It was built at Dodge City in Warren, Michigan (1500 only); St. Louis, Missouri; and Saltillo, Mexico. Information courtesy of Dodge.

How many miles does a Dodge Ram 2500 drive?

1st owner drove an estimated 0 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 27,981 miles/year • 4th owner drove an estimated 0 miles/year • 5th owner drove an estimated 0 miles/year • 6th owner drove an estimated 0 miles/year • 7th owner drove an estimated 0 miles/year.

Do you know the gear ratio on a Dodge Ram?

This article applies to the Dodge Ram (2002-2008). Knowing your rear differential’s gear ratio can help you get an average reading of your Ram’s fuel mileage, as well as determine the appropriate towing capacity. Another thing you should know is that the differential must be regularly maintained and serviced by replacing its fluid.

Is the Dodge Ram 1500 a Quad Cab?

Use our vehicle selector to find the gear that will fit your Dodge Ram pickup. With an oversized grille and styling that really says “Made in the U.S.A,” the Dodge Ram 1500 Quad Cab is one of the most distinctive vehicles on the road today.

What’s the best way to remove a brake drum?

Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.

What happens when you change the drum on a car?

Most drum brakes on cars and other common vehicles are hydraulically powered. If there is a leak in the hydraulic system, you may notice fluid inside the drum and on the brake shoes. Usually, this is accompanied by decreased brake performance. If necessary, replace the leaky wheel cylinder.

How is a brake drum puller attached to a wheel?

Place each of the brake drum puller’s 3 hooks evenly around the brake drum’s flange. Ensure that the screw in the middle of the brake drum puller lies above the middle of the wheel hub. Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum.

Do you need to replace your brake pads and rotors?

But sometimes, it is very possible to lubricate and release the stuck caliper pins. And in other cases, you need to replace the calipers completely. Also, it’s likely that you will need new brake pads and rotors. Whenever there is a brake job done on your car or replace a brake pad, you must replace the shims.

How do you change front disc brake pads?

Check periodically to make sure it is not running over. If needed, a clean rag can be inserted into the reservoir soaking up some of the fluid and remove it. If this compression is not done, you won’t be able to get the caliper assembly over the new pads. Fit the caliper assembly back into place, making sure the clips are placed correctly.

What do brake pads do on a car?

Brake pads are specifically the part of the brakes that apply pressure to the rotors or brake discs, “squeezing” the vehicle to a stop.

How to replace front brake pads and rotor Ram 1500?

How to Replace Front Brake Pads and Rotor Ram 1500 2009–2018 – YouTube Here is a video explaining how to change the front brakes on a Dodge Ram 1500 2009–2018. This is a simple and straight forward job that anyone could do just

How do you know when to replace brake pads?

Unless brake pads were replaced recently, pads must be replaced while replacing the rotors. Measure the thickness of brake rotors. Remove and replace rotors and pads. Perform a brake safety inspection. Perform test drive. It is a good idea to get the thickness of brake rotors measured annually.

What do I need to replace front brake rotors?

If you choose front brake rotors, both front wheels will get new rotors. This service comes with brake pads. Unless brake pads were replaced recently, pads must be replaced while replacing the rotors. Measure the thickness of brake rotors. Remove and replace rotors and pads. Perform a brake safety inspection. Perform test drive.

What happens when your brake rotors wear out?

As the rotors wear out (become thin or warped), they are unable to dissipate the heat caused by the braking system. This will cause the brake fluid to boil and reduce the effectiveness of brake system significantly.

Are there rear brakes on a Dodge van?

My van has front brakes and since I put on the master cylinder, the brake system light and the ABS light are no longer illuminating. But it seems illogical that those warning lights would go out when I do not have rear brakes. My van has disc brakes on the front and on the rear there are drum brakes.

What are the brakes on a 1994 Dodge truck?

The body harness attaches to the body computer, power seats, rear dome light and seat belts. Some 1994 trucks had front ABS brakes. If there is an electric wire attached to the flexible hydraulic brake hose, the vehicle has ABS brakes. If there is no wire, the vehicle does not have front ABS brakes.

What kind of parts are in a Dodge truck?

Our NOS (New Old Stock) Dodge truck parts group has 60 items including window regulators, door latches, tailgates, fenders and wiring harnesses. We have Mopar parts books, Dodge service manuals and Hollander Interchange manuals for 1961-2006 Dodge trucks.

Where to buy brake rotors for Dodge Ram 3500?

Shop AutoZone for Dodge Ram 3500 Brake Rotor. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

Do you need a Mopar rear disc brake conversion kit?

In this kit you receive everything you need to mount single piston disc brakes to your Mopar 8-1/4, 9-1/4 Rear Axles. All components used in these Mopar rear disc brake conversion kits are new high quality, precision machined products with a zinc plated finish to reduce corrosion and extend the life of your brake system.

* click on a group below to visit that section * GROUP CONTENTS 25 Body – Miscellaneous Lock Cylinders and 26 Interior Trim (By Body Code) All Interio 27 Heater & Air Heater, Air Conditioning Sy 28 Emissions Systems Air Pump…EGR System.

How do you remove the brake rotor from a Dodge Ram?

The only thing keeping it from being removed at this point is the brake caliper’s mounting bracket. There are two bolts that hold this bracket onto the steering knuckle. Once these are removed, you can remove the caliper mounting bracket, and finally remove the brake rotor. The brake rotor might take a few taps with a mallet to remove it.

What kind of brake pads do I need for a Dodge 1500?

As part of our series on the best aftermarket parts for the Ram 1500, we bring you the 10 best Brake Pads for Dodge Ram 1500 Pickup. Do ensure that the product you picked is compatible with your model, though.

Where can I get parts for my Dodge Ram 2500?

If you find you need to replace a part, do not hesitate in contacting PartsGeek.com, where the best Dodge Ram 2500 oem and aftermarket parts can be found at reasonable prices. Awesome service! Fairly fast delivery. Thought it was strange our part sat in New Jersey for 6 days.

What kind of suspension does a Dodge Ram have?

Suspension – mixed (front – torsion, rear – leaf springs), or front – spring on the models of the third generation and fully spring on the models of the fourth generation. Drive type – all-wheel-drive or only rear-wheel drive.

What kind of body does Dodge Ram 2500 have?

This Dodge Ram 2500 was available with two-wheel or four-wheel drive and came in a variety of body styles and trim configurations. A regular cab, Crew Cab, and Mega Cab comprised the body styles. Trim levels consisted of the basic ST, the volume-selling SLT and the luxurious Laramie.

Do you need to repair your Dodge Ram 2500?

Your Ram 2500 is always a nicely built vehicle but over time even the most well-protected cars and trucks require replacement part maintenance and repair of damaged components.

Is the Dodge Ram 2500 brake line genuine?

We offer a full selection of genuine Dodge Ram 2500 Brake Lines, engineered specifically to restore factory performance. Please narrow the Brake Line results by selecting the vehicle.

Where can I get brake rotors for my Dodge Ram?

Select your preferred location and we’ll note which parts are ready to be picked up TODAY. Select your preferred location and we’ll note which parts are ready to be picked up TODAY. Brake Rotors, Cross-Drilled/Slotted, Iron, Zinc Dichromate Plated, Front, Dodge, Pair

Where can I buy a Dodge Ram brake caliper?

Shop AutoZone for Dodge Ram 2500 Brake Caliper – Front. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

What kind of truck is the Ram 2500?

2021 Ram 2500 1 EXTERIOR. Introducing the 2021 Ram Heavy Duty Limited Night Edition. This special edition features a black Limited… 2 INTERIOR. 3 SAFETY AND SECURITY. Available in multiple trims. Select a Ram truck to explore. More …

What’s the name of the new Ram truck?

. The award-winning interior from the 2019 Ram 1500—with 100% leather seating—is now available on the new 2019 Ram 2500 Limited and Laramie Longhorn ® models. A bold new look and six prominent grille designs provide an unmistakable presence—on road and off. —now with a 115-volt power outlet.

Why is the third brake light on my Dodge Ram leaking?

The third brake light seal is the major culprit mentioned most often, and it’s the first place most people check. Those who have been through this report that fixing the seal there will fix the problem. At the same time, there are many owners who have tried this, and still get their shoes wet when they hop in the cab.

Is the cab of a Dodge Ram leaking?

It is known to be a reliable truck for the most part, but many model years have water leaking into the cab. Even though the Dodge Ram is praised as being a good family vehicle, many owners wish they had never bought one.

How do you remove brake rotors on a Dodge Ram?

While removing the brake rotors was basically the same for the 1/2-ton and 3/4 ton Rams, the 1-ton version added a slightly different procedure. Lift the Dodge Ram on a vehicle or truck lift to a suitable height to work on. Remove the lug nuts using an impact gun and a 7/8-inch impact socket or a 22 mm impact socket.

When to pump the brake pedal on a ram?

Be sure to pump the brake pedal once the Ram is back together to restore the compressed caliper piston to its seated position. Otherwise there will be no braking response until the pistons extend outward from the caliper piston bore. This, however, can cause a serious accident if there are any nearby obstacles.

How do you remove the center cap on a Dodge Ram?

Lift the Dodge Ram on a vehicle or truck lift to a suitable height to work on. Remove the lug nuts using an impact gun and a 7/8-inch impact socket or a 22 mm impact socket. Remove the center cap–secured by the tapered lug nuts–and then remove the wheel.

How do you change the brake pads on a car?

New brake pads should always be greased at their contact points, in addition to greasing the caliper guide pins and replacing the brake pad hardware, if applicable. Once the caliper has been compressed, you can then replace the caliper and caliper bolts, bleed the brakes, and replace the wheel.

What’s the difference between front and rear brake pads?

Front and rear brake pads may appear similar, but they are very different. On most vehicles, the front brakes apply the most pressure during braking. This requires the front pads to be larger than the rear pads, but even with their larger size, the front pads normally wear out quicker than the rear.

How to change rear brake pads on Dodge Ram 2500?