Easy lifehacks

How to reset a fuel filter alert on a GMC Duramax?

How to reset a fuel filter alert on a GMC Duramax?

This must be done manually from inside the cab of the truck. Press and hold the return arrow or select button (depending on model) on the right side of the steering wheel for five seconds while the fuel filter message is displayed. Follow the subsequent steps if your truck does not have steering wheel control buttons.

When does the fuel filter warning light go out?

Have the car checked out with diagnostic scan tool to find the saved code or codes. Don’t ignore this warning light or the system will fill with water and start leaking it to the engine. Once the water has been drained from the filter, this warning light should go out on its own.

Is it safe to drive with the fuel filter check light on?

The fuel filter check engine light warns you when your diesel fuel filter is full, and needs to be emptied to avoid engine damage. Is it safe to drive with the fuel filter warning light on? Diesel engines are quite different from their gasoline counterparts.

How do I remove the fuel filter alert?

However, the act of replacing the fuel filter will not erase the alert from the screen. This must be done manually from inside the cab of the truck. Press and hold the return arrow or select button (depending on model) on the right side of the steering wheel for five seconds while the fuel filter message is displayed.

The fuel filter check engine light warns you when your diesel fuel filter is full, and needs to be emptied to avoid engine damage. Is it safe to drive with the fuel filter warning light on? Diesel engines are quite different from their gasoline counterparts.

Have the car checked out with diagnostic scan tool to find the saved code or codes. Don’t ignore this warning light or the system will fill with water and start leaking it to the engine. Once the water has been drained from the filter, this warning light should go out on its own.

What should I do if my fuel filter is not draining?

Remember to change out the fuel filter at the right service intervals as draining the water will not remove all the particulates that are caught in the filter. Our certified technicians are always available to assist you in diagnosing any problems with your car’s fuel filter and they can drain or replace your fuel filter for you.

How does a fuel filter work on a car?

Inside the fuel filter is a fluid level sensor that keeps track of the amount of water that has been collected. Once the level starts reaching maximum capacity, the fuel filter warning light will illuminate to let you know to empty the filter. On manual systems, a valve at the bottom of the filter will let the water drain out once opened.

How do I reset the fuel filter on my car?

This message will appear when a reset is performed either by using the steering wheel controls or the following manual procedure. For vehicles with steering wheel controls, press and hold the select button for five seconds while the FUEL FILTER LIFE message is displayed. This message will appear on the DIC for ten seconds.

Can a fuel filter be replaced on a 2005 Chevy Silverado?

Here is how to replace the fuel filter to keep your fuel system nice and clean. Note that 2005 and later models are equipped with a non-replaceable fuel filter, which is built into the fuel sender assembly. Fuel is extremely flammable, so take extreme caution when working with the fuel system.

How to reset fuel filter reminder you diesel place?

If so, go to the fuel filter life and press and hold the key on the bottom right hand side, until it resets. In order to get to the fuel filter life percentage, press the bottom left button on the sterring wheel until you see it. Click to expand… Too bad the salesperson couldn’t have been that helpful.

This must be done manually from inside the cab of the truck. Press and hold the return arrow or select button (depending on model) on the right side of the steering wheel for five seconds while the fuel filter message is displayed. Follow the subsequent steps if your truck does not have steering wheel control buttons.

However, the act of replacing the fuel filter will not erase the alert from the screen. This must be done manually from inside the cab of the truck. Press and hold the return arrow or select button (depending on model) on the right side of the steering wheel for five seconds while the fuel filter message is displayed.

When do I need to change my fuel filter?

This alert system will let you know when to change your engine oil, when you have water in your fuel, as well as letting you know that your fuel filter will need changed soon. However, the act of replacing the fuel filter will not erase the alert from the screen. This must be done manually from inside the cab of the truck.

This alert system will let you know when to change your engine oil, when you have water in your fuel, as well as letting you know that your fuel filter will need changed soon. However, the act of replacing the fuel filter will not erase the alert from the screen. This must be done manually from inside the cab of the truck.

How does the Duramax engine alert system work?

Some Chevrolet and GMC trucks equipped with the Duramax diesel engine come standard with an alert display in the dashboard. This alert system will let you know when to change your engine oil, when you have water in your fuel, as well as letting you know that your fuel filter will need changed soon.

How to reset the oil light on a GMC Duramax?

Depress the accelerator and brake pedals simultaneously and fully and hold them down for ten seconds. Release the accelerator and brake pedals and turn the ignition key off. The system is now reset. How to Reset the Oil Life on a 2007 How Do I Turn off a Maintenance Light How to Reset the Oil Light on a 2003 …

Does the fuel filter need replacing?

Simply noticing a sudden drop in fuel efficiency is enough for the car owner to suspect that the fuel filter needs to be replaced. A rule of thumb for maintenance is that fuel filters should be replaced approximately every 24,000 miles or once every two years.

How often does fuel filter changed?

You must change your vehicle’s fuel filter at 50,000 miles. Subsequent filters should also be changed at least every 50,000 miles, but changing them annually is even better.

How do I replace diesel fuel filter?

How to Change a Diesel Fuel Filter Step 1 – Locate the Filter Step 2 – Detach the Old Filter Step 3 – Install the New Filter Step 4 – Clean Up Step 5 – Refill Fuel Lines with Fuel Step 6 – Dispose of Old Filter

How often should you change fuel filter for diesel?

For most Diesel trucks it is recommended that you replace your fuel filter every 10,000-25,000 miles depending on how you drive, how often you commute and what type of vehicle it is. Most cars will have information on how frequent you should change the fuel filter in the owner’s/maintenance manual.

How do you remove the fuel filter from a car?

Removing the Old Fuel Filter Disconnect the battery. Locate the fuel filter. Jack up the car if necessary. Place a bowl or bucket beneath the fuel filter. Remove the clips holding the fuel filter in place. Remove the fuel lines from the filter. Slide the fuel filter out of its bracket.

How big is the fuel filter in a diesel truck?

The fuel filters in diesel cars and trucks are usually much larger, and the whole fuel system is much more complex. Diesel engine fuel systems are also under a lot more pressure, with modern common rail systems producing over 1000 bar of pressure. Accidentally releasing such high pressure could result in injury. Locate your vehicle’s fuse box.

What to do if fuel spills out of fuel line?

Although you relieved the pressure in the fuel line, there may be a bit of fuel left in the line that can spill out when disconnected from the fuel filter. Place a bowl or bucket beneath the fuel filter to catch any fuel that drips or pours out. Do not mix the fuel with oil or coolant to be recycled.

How do you remove the fuel filter from a Chevy Silverado?

Flare nut wrenches will help to keep from rounding off the fitting of the fuel filter. The fuel filter is attached to the vehicle by a bracket. To loosen the bracket and remove the fuel filter, loosen the nuts that hold it into the mounting bracket.

What is the fuel filter for a Duramax 01-16?

The AFE 44-FF011 Pro-Guard D2 Fuel Filter for your 01-16 GM 6.6L Duramax delivers increased flow and efficiency that are demanded in a Diesel environment. High performance and high flow all in one quality engineered filter. This fuel filter meets or exceeds new GM specifications.

Which is water in fuel sensor for Duramax?

The Dorman 904-110 Water In Fuel (WIF) Sensor is an affordable replacement option for your 2001-2011 GM 6.6L Duramax. Dormans Water In Fuel Sensor is constructed from high-quality materials to withstand wear and tear due to repeated fuel filter service and other factors.

How do I reset the fuel filter monitor?

Reset the fuel filter monitor. For vehicles with steering wheel controls, press and hold the select button for 5 seconds while the FUEL FILTER LIFE message is displayed. This message will appear on the driver information center (DIC) for ten seconds.

Why does the fuel filter life indicator not reset?

The fuel filter life indicator does not reset after fuel filter change. What am I doing wrong? The fuel filter life indicator does not reset after fuel filter change. What am I doing wrong? – Answered by a verified Chevy Mechanic We use cookies to give you the best possible experience on our website.

This message will appear when a reset is performed either by using the steering wheel controls or the following manual procedure. For vehicles with steering wheel controls, press and hold the select button for five seconds while the FUEL FILTER LIFE message is displayed. This message will appear on the DIC for ten seconds.

Depress the accelerator and brake pedals simultaneously and fully and hold them down for ten seconds. Release the accelerator and brake pedals and turn the ignition key off. The system is now reset. How to Reset the Oil Life on a 2007 How Do I Turn off a Maintenance Light How to Reset the Oil Light on a 2003

If so, go to the fuel filter life and press and hold the key on the bottom right hand side, until it resets. In order to get to the fuel filter life percentage, press the bottom left button on the sterring wheel until you see it. Click to expand… Too bad the salesperson couldn’t have been that helpful.

Why is my Duramax diesel engine not working?

The trucks computer keeps track of how much fuel needs to be added or subtracted from each individual cylinder to make the engine run smoothly, and this value is called the balance rate. If one cylinder is contributing too much or not as much as the rest, the cause is usually a bad injector and the cure is a replacement.

Some Chevrolet and GMC trucks equipped with the Duramax diesel engine come standard with an alert display in the dashboard. This alert system will let you know when to change your engine oil, when you have water in your fuel, as well as letting you know that your fuel filter will need changed soon.

What does the MAP sensor on a fuel injection engine do?

The MAP sensor can be found on most fuel injection engines made today. These are engines that use high pressure to pump gasoline which then vaporizes it. What the MAP sensor does is it assists the engine in figuring out what it needs to have the best combustion possible.

Can a bad MAP sensor cause engine failure?

MAP sensor on footwell inside engine compartment. A bad manifold absolute pressure (MAP) sensor can upset fuel delivery and ignition timing. Depending on your vehicle model, your engine might experience one or more of these performance problems: However, these symptoms are not exclusively symptoms of a failed MAP sensor.

How can I Keep my Duramax Diesel pump healthy?

However, there are measures you can take to keep the pump happy and healthy, the first being to always buy your diesel from a high-traffic, reputable filling station that’s known to dispense good, clean fuel. Second, always change the fuel filter at or before the recommended service interval.

Where is the CP3 injection pump in a Duramax?

The CP3 injection pump sits in the valley of the engine between the cylinder heads and is driven by the camshaft gear, and it has two main jobs: get fuel from the tank up to the engine, and pressurize the fuel to 26,000psi and ultimately inject it into the engine.

Why does my check engine light come on when my fuel filter is bad?

Check Engine Light Comes On Fuel filter problems can also cause the Check Engine Light to come on. Some vehicles come equipped with fuel pressure sensors that monitor the pressure of the overall fuel system. A clogged fuel filter may cause low pressure, which will set off the Check Engine Light to alert the driver — if detected by the sensor.

How to reset a GMC Duramax maintenance light?

Wait for five seconds. Depress the accelerator and brake pedals simultaneously and fully and hold them down for ten seconds. Release the accelerator and brake pedals and turn the ignition key off. The system is now reset. How to Reset the Oil Life on a 2007 How Do I Turn off a Maintenance Light How to Reset the Oil Light on a 2003 …

Wait for five seconds. Depress the accelerator and brake pedals simultaneously and fully and hold them down for ten seconds. Release the accelerator and brake pedals and turn the ignition key off. The system is now reset. How to Reset the Oil Life on a 2007 How Do I Turn off a Maintenance Light How to Reset the Oil Light on a 2003

Author Image
Ruth Doyle