What does the OBD code p0700 stand for?

P0700 code definition. P0700 is a generic OBD-II code that is indicating a fault within the transmission control system.

Why is the Check Engine Light set to p0700?

P0700 is set when the PCM detects a malfunction in the transmission control system. This malfunction causes the vehicle to set a Check Engine Light and trigger a failsafe mode.

When does the transmission control system set p0700?

P0700 is set when the PCM detects a malfunction in the transmission control system. This malfunction causes the vehicle to set a Check Engine Light and trigger a failsafe mode. Once the failsafe mode is set it will remain until the fault is repaired or normal operation is detected.

What should the slip speed be on a p0700?

When looking at the Toque Converter RPM versus the Input Shaft RPM, observe if the scan tool data has a Converter Slip Speed PID or Parameter Identification. This can be very helpful in the diagnosis of an intermittent P0700. If the Lockup System is functioning correctly, the Slip Speed value should never be above 50 RPM.

What does the code p0700 on OBD-II mean?

The OBD-II scanner error code P0700 problem is a generic code that applies to vehicles equipped with OBD-II. It refers to the transmission control module (TCM) in the automatic transmission. The P0700 code is informational. The code points to a general fault, not a direct fault.

What is the OBDII code on a Chevy Equinox?

P0300 is one of the most common OBDII codes that occurs in the Chevy Equinox.

What does trouble code P0300 mean on Chevy Equinox?

The P0300 Chevy trouble code will trigger the Equinox’s service engine soon light. The vehicle itself may begin to run rough. It depends on how serious the misfire is. The vehicle may produce excess vibration, espescially at lower RPM

What to do if your p0700 is having trouble?

Monitor the Slip Speed, Lockup Duty Cycle and Output Shaft Speed for irregularities. One thing to try when fixing the P0700 code is to clear the code and take it on a road test. Before clearing out the data, record all present codes and any data from the scan tests. After the second road test, look for the codes that appear.

OBD-II Code P0700 is defined as a Transmission Control System Malfunction The purpose of the automatic transmission is to match the engine’s optimum power and torque characteristics to the driver’s desired rate of acceleration and speed by auto-selecting different gear ratios or ‘speeds’ to power the wheels.

Where can I find the OBD code for my Acura?

If there is no procedure for your manufacturer specific code, then I suggest referring to a similar generic OBD II code (these are listed numerically by system type) to get a good idea of what to look for. If at this point you still need assistance use the “Get Help” link and let us know how we can help.

What does DTC stand for in OBD-2?

This diagnostic trouble code (DTC) is a generic OBD-II powertrain code. It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may vary depending on the model.

Why do I get a 3rd gear OBD code?

Modern vehicles equipped with automatic transmissions / transaxles use a torque converter between the engine and transmission to increase the engine torque output and drive the rear wheels. This code can show up in vehicles with an automatic transmission when there is a problem shifting into 3rd gear, or while driving in 3rd gear.

What does DTC stand for in OBD code?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model. What does that mean?

Where is the fault code stored in a p0700?

P0700 means that a fault code is stored in the TCM. However this doesn’t rule out the possibility of a failed PCM or TCM (unlikely). For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module.