How do you remove a front CV axle?

Raise & support the vehicle properly, remove the passenger front wheel, splash shield, & then remove the passenger front CV axle. 2. On S4WD models, remove the electric axle actuator from the axle disconnect assembly by removing the 2 bolts and electrical connector.

How do you remove a front axle on a s4wd?

Excessive play in the axle shaft connection inside the axle disconnect. 1. Raise & support the vehicle properly, remove the passenger front wheel, splash shield, & then remove the passenger front CV axle. 2. On S4WD models, remove the electric axle actuator from the axle disconnect assembly by removing the 2 bolts and electrical connector.

How many axles does a Chevy Silverado have?

An fwd car will have one for both the passenger side and driver’s side. An AWD car will have the same, but additionally two in the rear of the car.

What is the GM name for front axle disconnect?

This part of the article we will call the front axle disconnect, the proper GM name of Intermediate Shaft Bearing Housing Assembly as this system, the name actually makes sense. This is because the differential intermediate shaft slides through the Intermediate Shaft Bearing Housing and rides on bearings inside the assembly.

How to replace a front axle shaft seal?

If you have ever owned a GM four wheel drive vehicle then there is a good chance you have had a front axle shaft seal leak. We replaced the RH output shaft seal on a Tahoe but it is the same for Silverado, Sierra,Suburban and Yukon. Part one shows details on the tear down and part two with guide you through the reassembly. Loading…

When do you replace the front axle on a Chevy Silverado?

In this video, we’re going to show you how to replace the right hand, or passenger side, front axle on this 2011 Chevy Silverado. This is a 1500. The procedure for the left axle is pretty much the same, and it’s also the same for these trucks for model years 2007-2013 for both this Chevy Silverado 1500, as well as the GMC Sierra.

What do I need to replace front CV axles?

In this repair we use new axle or axles from 1AAuto.com, jack and jack stands, 15 to 22mm sockets with a ratchet extension. You’ll need a breaker bar and a pipe for some extra leverage, a 36mm socket, and I separate that one out because it’s not one that’s usually in your regular socket set.

What to do if your CV axle is not catching?

Jack up your vehicle and put on the parking brake. Rotate your front tires forwards or backwards and if you hearing grinding and/or clicking, and the CV joint is not catching, most likely the one that needs replacement will be there.

What to do if your CV joint is not catching?

Rotate your front tires forwards or backwards and if you hearing grinding and/or clicking, and the CV joint is not catching, most likely the one that needs replacement will be there. Also check your CV joint boots, and if you see a broken boot with leaking fluid, that is a good indication of damage. Thanks!

Where is the outer tie rod on a CV axle?

Unbolt the outer tie rod from steering knuckle. The outer tie rod is literally a rod bolted to the steering knuckle, which is just behind the rotor. This piece will likely be bolted with another 17mm bolt. Like the axle nut, this bolt may be held in place with a cotter pin. Penetrating lubricant may help you more easily remove the pin and bolt.

How do you remove a CV joint axle?

If auto theres no bolts on the trans it just slides out i believe. There are four bolts holding the axle in. Three nuts for the lower control arm come out so the arm swings down. One large axle bolt. That’s it. then you take a prybar and put itbetween the trans case and the axle shaft and use a hammer to hit hte bar.

What to do if your CV axle nut is stuck?

You will need to use pliers to straighten the two bent ends of the cotter pin before you can remove it. If the pin is stuck, try spraying it the a penetrating lubricant from a hardware or automotive store. The lubricant should actually help with the axle nut as well. Remove the axle nut. Once the cotter pin is out, you can remove the axle nut.

What’s the best way to replace an axle?

Use a pair of side cutters (dikes) to remove the cotter pin from the axle snout. There might also be a star wheel which can be removed after the cotter pin. 2. Remove the Axle Nut There are three methods that can be used to loosen and remove the axle nut. The first way is what is shown by using an impact wrench which just happens to be the easiest.

How to replace an automotive CV axle-2carpros?

Reinstall the CV Axle Nut Reinstall the CV joint axle nut by hand to avoid cross threading and then tighten to manufactures specification with is usually between 120 and 140 foot pounds for torque. Install a new cotter pin and then bend one end if it over the axle threads to hold it in place while cutting off any excess and you are all set.

How much does it cost to replace front CV axle?

On average, replacing a CV boot, which in most cases will mean replacing the axle/shaft, can be expensive since it is difficult to access. On average, it can cost between $175 to $350+ per CV boot, depending upon the model, make and type of car, although some luxury vehicles can cost upwards of $1,000 each.

When does a CV axle need to be replaced?

Usually, the CV axle will need to be replaced if it is damaged enough to cause vibrations. CV axles serve as the final link between the engine and the wheels. They serve the important function of transferring the torque from the drivetrain to the vehicle’s wheels in order to move the vehicle.

What is a front axle assembly?

A front axle assembly is the unit that connects two wheels at the front of a vehicle, and allows those wheels to rotate freely and sometimes independently. Very simple front axle assembly models may not include much beyond the axle, axle housing, and bearings to allow the axle itself to rotate,…

How do you remove a front CV axle?