Are there any problems with the bobcat 773?

Other problems are mostly associated with a used machine. You should detect leaks at the loader’s wheels and signs of wear and tear on the bushings, especially if you plan to use multiple attachments. Bushings bear the biggest load when operating a loader, so this part will be the most vulnerable to wearing out.

Is the oil pressure sensor on a bobcat connected?

Shutdown, No Coolant Warning, High Engine Temperature Engine Oil Pressure Sensor Wiring Not Connected (See Operation & Maintenance Manuals for complete listing of codes)

What do you need to know about a bobcat?

Fuel level Battery voltage Engine oil pressure Engine coolant temperature and coolant level warning/ shutdown symbol Shutdown symbol Warning symbol Hour meter/code display Charge pressure and filter condition Air filter condition 10.Glow plug 11 .Engine speed 12. Hydraulic fluid temperature

What’s the low hydro pressure code on a bobcat?

Discussion in ‘ Skid Steers ‘ started by jljr42, Jan 24, 2010 . 2005 bobcat t190 705 hours, low hydrostatic pressure code 05-09 and extremely low code 05-14, 05-15 followed by engine shut down. only does it at idle which is 1150 rpm. quits doing it at 1300 rpm.

How does diagnostic tool work on Bobcat loader?

Diagnostic Tool can access loader sensors’ current information/status. Diagnostic Tool can store a two-minute snapshot of information from each sensor/ switch EVEN DURING LOADER OPERATION. Information can then be printed out on a separate printer. (This aids in diagnosing intermittent problems.)

Can you buy a Bobcat skid steer loader?

Buying a used skid steer loader requires you to understand Bobcat 773 specs and understand Bobcat 773 problems, be they problems inherent in the model or problems associated with used equipment in general. Bobcat 773 is known for its oversized arms, which give it a higher and longer reach when lifting the load.

How many hours does a Bobcat loader need?

The longer it is used, the more prone it is to problems. The most reasonable operational hours for a used loader are between 1000 and 2000 hours. You should buy the machine as a second owner, though it may not be easy, especially if you buy a decades-old machine.

What makes a 773 G series loader so good?

The 773’s low-profile, vertical-path lift arm design and innovative G-Series cab enhance the operator’s view to key areas during operation: the sides, front and rear corners of the loader. Even with the optional front door, the 773 G-Series offers the operator increased visibility.

When did the bobcat 773 skid steer loader come out?

Bobcat 773 is a skid steer loader that first appeared on the market in 1994. Although it is considered an old loader today, it is still a worth-purchasing loader. By understanding Bobcat 773 specs and problems as well as the right way to buy it, you can find this loader reliable equipment to use at home. Table of Contents.

What’s the difference between Bobcat 700 and 773?

Unlike its more modern counterparts, Bobcat 773 doesn’t support a two-speed option to increase its travel speed. Bobcat 773 is the biggest skid steer loader in the 700 series, but it is still considered a compact machine.

What’s the speed of a Bobcat skid steer?

In terms of speed, Bobcat 773 offers decent travel speed up to 7 mph (11 km/hr.). Unlike its more modern counterparts, Bobcat 773 doesn’t support two-speed option to increase its travel speed. Bobcat 773 is the biggest skid steer loader in the 700 series, but it is still considered a compact machine.

Where do I find the fault code on my Bobcat?

First select your vehicle and then find the fault code in that page. Although we try our best to provide our visitors with the most accurate information that we can find about your skid steer, we cannot be held responsible for any errors. Bobcat is equipped with a universal skid steer quick hitch.

What does the error code 03-09 mean on a bobcat?

Error codes indicating that there is something wrong with the equipment or machine you are using. The error code of 03-09 is one of the most common codes that you will encounter. It indicates “Low battery voltage”. When your Bobcat equipment is using a rechargeable battery, make sure there is still enough power to run the machine.

What to do if your bobcat won’t move?

2000 bobcat 773 will not… 2000 bobcat 773 will not move. Parking brake locked. Appears no power is going to brake solenoid. Both circuits, pull and hold, check good. Fuse, relay, foot switch, and seat lock all good. All lights except park brake come on when “push to operate” is engaged. Pushing traction lock bypass has no effect.

Do you need to know the bobcat fault code?

You need to know the most common Bobcat fault code list because when you are using Bobcat, usually the Bobcat fault code list will appear on display. Those who use Bobcat tractors, excavators, and other types of heavy machinery and encounter error codes every once in a while.

What should I know about Bobcat service videos?

Protect your investment by learning how to perform regular maintenance yourself. Check out our Service Videos below to learn how you can keep your machine running longer without a lot of downtime. For additional maintenance information, refer to your operation and maintenance manual.

Where is the hydraulic interlock valve on a bobcat 773?

Your hydraulic main control valve should look similar to the one in the pic below, the red arrow points to the BICS solenoid that controls the hydraulic interlock valve, that solenoid has to be powered up to unlock the lift/tilt functions and it’s controlled by the BICS controller to the right of the seat.

Is there a hydraulic problem on my Bobcat 773?

Ok as said in the title we have a hydraulic problem on our bobcat 773. The bobcat runs fine and drives fine but the tilt and raise will not work. Its like it is not disengaging. The bar that you pull down is unlocking the pedals. When you try and tilt or raise it does load the engine up but doesnt move.

Why does my Bobcat turn over but not start?

It is also within the realm of possibility that the power source (battery) is weak, which is unlikely if the starter cranks the machine, or that interconnecting wiring is damaged and limiting the current to the solenoid. Check voltage at the solenoid while the key is turned on, without the solenoid pulled in and with it pulled in.

Why does the tilt and raise on my Bobcat not work?

The bobcat runs fine and drives fine but the tilt and raise will not work. Its like it is not disengaging. The bar that you pull down is unlocking the pedals. When you try and tilt or raise it does load the engine up but doesnt move. On the back of the cab right next to the seat theres like 5 lights.

Where is the seat bar switch on a bobcat?

It’s located on the left side and needs to be working to allow the machine to move. My seat bar would only work in random positions and the spline on the indexing bushing was worn out. Loading…

What are the safety switches on a bobcat?

Ours has two switches — one is a weight in the seat switch and the other is the seatbelt. When ours is locked up, you have to unlatch and re-latch the seatbelt, with some authority, and all is well again. Can’t speak to your green lights or exactly what safety switches a Bobcat has.

Are there any replacement seats for Bobcat skid steers?

Your shopping seats and lap bar replacement parts for Bobcat® skid steer loaders. We couldn’t find any results for your search. No filters have been applied yet.

It’s located on the left side and needs to be working to allow the machine to move. My seat bar would only work in random positions and the spline on the indexing bushing was worn out. Loading…

How many Bobcat fan pulleys are there?

In stock on June 29, 2021. . Mover Parts Cooling Fan Pulley Tensioner Kit 6662997 6702474 for Bobcat 653 751 753 763 773 7753 853 863 864 873 883 963 A220 A300 S130 S150 S160 S175 S185 S205 S220 S250 S300 T140 T180 T190 T200 T250 .

How many Bobcat mover parts are in stock?

Mover Parts Cooling Fan Pulley Tensioner Kit 6662997 6702474 for Bobcat 653 751 753 763 773 7753 853 863 864 873 883 963 A220 A300 S130 S150 S160 S175 S185 S205 S220 S250 S300 T140 T180 T190 T200 T250 . Only 16 left in stock – order soon.

Why is the parking brake on my Bobcat not working?

Parking brake locked. Appears no power is going to brake solenoid. Both circuits, pull and hold, check good. Fuse, relay, foot switch, and seat lock all good. All lights except park brake come on when “push to operate” is engaged. Pushing traction lock bypass has no effect. Codes read “none”. All visible wiring appears good.

What does the bobcat 773 loader look like?

Bobcat 773 looks unique with its large black arms—a feature that is rare even in Bobcat’s latest models. Their large arms not only give Bobcat 773 a mean look but also provide the loader with a higher and longer reach, especially when lifting. 4. Rebuilt Bobcat 773 is available.

Why does my Bobcat Run but won’t move?

The lights all work in the control box and then after a few minutes the valve light starts flickering and the arm\bucket doesn’t move unless i restart the machine. Then sometimes the traction light will go off after the valve light does. The red 10 fuse blew a few times. Thoughts? Hi. New to site so sorry if I make a mistake. I own a 453 F series.

Is the valve on a bobcat C series?

Our bobcat is a C series. On the BICS its called the valve. The valve the seat bar and system activated lights on the BICS are not lit up either. As for the seat switch its never been connected and was running fine before hand.

How does the BICS controller work on a bobcat?

The BICS controller gets inputs from the seat switch, lap bar, and enable button (if equipped). Once it gets input from these components it sends voltage to the BICS solenoid valve to unlock the lift/tilt functions. DarenK likes this.

How does the bobcat hydraulic fluid sensing system work?

Hydraulic fluid temperature BOSS Bobcat Operation Sensing System Monitor Service Codes

What are the warning signs on a bobcat?

HP – Hydraulic Oil Pressure -1 – Shutdown (Engine can be restarted for 30 second periods to move loader) -2 – Warning The versatile Bobcat quickly turns into a multijob machine with a tight-fit attachment hook-up …etc from bucket to grapple to pallet fork to backhoe, and a variety of other attachments.

Is there a rebuilt version of the bobcat 773?

Rebuilt Bobcat 773 is available. If you worry about the condition of your decades-old equipment, you can buy a rebuilt model. A rebuilt model is made from used components with reasonable quality to ensure that the final product is the best of all used equipment. Some rebuilt models even come with a warranty.

How much does a bobcat 773 skid steer weigh?

It has a four cylinder and weighes 5460 pounds. The 773 is shown left with a general bucket. View entire Bobcat 773 specifications below. Please click the button or scroll down to find our recommended Bobcat 773 Attachments. The 773 Skidsteer from Bobcat comes equipped with a universal skid steer quick hitch.

What kind of engine does a 1995 bobcat have?

1995 Bobcat 773 equipped with cab/ heat , bucket, and powered by a Kubota diesel. Just traded from local customer SOLID 773. COMES WITH STANDARD 68″ BUCKET (NOT PICTURED) .

What kind of engine does a Bobcat skid loader use?

En… BOBCAT 773 REMAN ENGINE TURBO, This Engine Fits 773 Bobcat Skid Loader,Engine Is Remanufacture/Rebuilt TURBO CHARGED ENGINE SPEC& ENGINE HAS NO TURBO BOBCAT REMAN ENGINE 743,753,763,773,7753,S130,S150,S175 REMAN KUBOTA ENGINES TO FIT BOBCAT SKID LOADERS REMAN ENGINE AND KUBOTA ENGINE OEM PARTS READY…

Are there any problems with the bobcat 773?