How does the clutch work on a Caterpillar D4?

Synchronizing the rotational speed between the engine and transmission, a clutch operates by applying pressure against the engine flywheel and the transmission input shaft. Over time, as the clutch is continually put through repeated engagement cycles, wear occurs on the internal surfaces, resulting in play, or slack, in the mechanism.

What’s the difference between D4C and D4D steering clutches?

D4C & D4D STEERING CLUTCHES The D4C (models 39A, 40A) and D4D (78A, 22C, 82J, 83Jand others) steering clutches went through a small design difference from the earlier D4 4G, 7J, 2T, 5T, and 6U/7U series. The early D4’s originally used the riveted on lining style of friction discs and progressed to the bimetallic 3F5504 discs.

How many friction discs do I need for D4D 83j?

TYPICAL PARTS PAGES SHOWING THE STEERING CLUTCH and BRAKES FOR D4D 83J If you need parts or service information for your particular model just email us at [email protected] There are many more files toward bottom of this page. OUT OF STOCK D4 FLYWHEEL CLUTCH FRICTION DISCS.2 REQUIRED PER CLUTCH @ 42.00 EA.

What kind of discs does a D4C use?

The D4C and D4D continued with the 3F5504 bimetallic discs while the steel discs and inner driving drums went through a change. The inner driving drums changed from straight splined driving hubs to a ramp style driving drum (8H1174) and this requires the use of the 2H6936 steel separator plates.

What kind of clutch discs does a D4e use?

The D4E uses the same oil type clutch discs as the oil type D4D and D4C’s. They use a different quantity so check the parts pages for quantities. Down below on this page you will also find a picture album of the basic removal and disassembly of the bevel gear cross shaft and the steering clutch packs.

Where to get parts for a Caterpillar D4 bulldozer?

I’m looking for (describe parts) for a D4 Caterpillar Bulldozer. Receive 3% off for joining our monthly discounts email newsletter. Parts specialists are available from 8am to 5:30pm EST. Give us a call to discuss how we can help you.

How to contact D4C steering clutches and brakes?

If you are in the US you may call 1-800-531-9021 or if you are outside the US, 1 208 342 8911. You may also email [email protected] for orders/questions. Our hours are Monday through Friday from 10 am Eastern Time to 6 pm Eastern Time (8 am Mtn Time to 4 pm Mtn Time). We are located 20 miles east of Boise, Idaho.

Is the steering brake on a D4 series 2?

The Series II was built from ’90 to ’93. Series III was from ’93 to ’01. My data has your machine as a Series II. I cannot get any other info since CAT does not keep many records that old. Donnie : If you have a Series II it will not have the adjuster by the seat.

Where is the clutch on a Caterpillar bulldozer?

Remove the clutch housing cover, located on the bottom of the bulldozer, with a socket wrench. Locate the single 1/2-inch bolt securing the center of the spider gear assembly. Loosen the nut on the bolt with a wrench.

What is the pin number on a D4C?

PIN number is XXXXX – D4C Model – Series III – Thanks but there is no 9/16 stud under the seat. Any suggestions? Dave Customer: By the way – can you tell me the year of this machine by the serial number I gave you?

How to release steering clutch on Caterpillar bulldozer?

DONT RELEASE the steering clutches but move the machine forward & back about 25metres each time say 3-4 times. Then drain the fluid & see repeat if it doesn’t clear. Uselk clean fluid the operate the CAT back and forth engaging the steering clutches & apply, release brakes as well.

Where can I find a Caterpillar engine forum?

This is an online forum where professionals who work with Caterpillar equipment and engines can exchange information, find answers, and get expert advice from their peers. To help you and other members get the most out of the community, please be sure to read our Guidelines.

Why does my Dozer have a snap sound?

There is an small shaft in the adaptor housing which maybe damaged. If you still have some movement in the hydraulics, but no real power, the main relief valve (fitted to the Dozer control valve – input section) maybe at fault. Pressures will need to be checked with a test gauge. Snap sound on my 850 d.

What is the CARB number on a Caterpillar D4?

The smaller D2 was a bit underpowered for the weight but the D4 was another machine and solid as. The Pony motor started the machine then the diesel engine kicked in once primed by the petrol -powered motor. The Pony motor carb kit: CAT part number or better yet the Zenith carb number should be a Zenith K2067 kit.

How to start a caterpillar d4-7u pony motor?

The oil pressure gauge will register oil pressure and the fuel pressure gauge (on the front left side of the engine) will go to the green. Now start the main engine by simply opening the throttle. Fill the ;ony motor gas tank with regularf petrol only.

When did the Caterpillar D4 7U series start?

The D4 actually started around 1937 with a G4 Series then evolved into the 7U Series of the 1940s and 1950s. The Caterpillar Company continued to build new D4s right up till now and they are a great machine. The smaller D2 was a bit underpowered for the weight but the D4 was another machine and solid as.

Do you need to adjust the brakes on a caterpillar Dozer?

If your linkage rods have not been adjusted, you will only need to do the field adjustment procedure. If the rods have been adjusted, you may need to recheck the lengths so adjusting the brakes will be in the correct relation to the steering clutch releasing.

Where is the adjuster on a caterpillar D3 Dozer?

Adjuster cover (4) must be installed with the notch facing away from the machine centerline. NOTE: Apply 5P3413 Pipe Sealant to bolts (1) that fasten housing assembly (9) and adjuster cover (4) to the steering clutch cover. NOTE: Lubricate shafts (10) with 5P0960 lubricant at assembly. When adjusting the brakes, the brakes must be released.

Do you need steering pedals on caterpillar D3 Dozer?

It should be a model D3B, G models are newer and only come as hydrostatic drive. G models have no steering pedals, just a single steering lever on the left. If your linkage rods have not been adjusted, you will only need to do the field adjustment procedure.

How do you measure the pedal travel on a caterpillar D3?

1. Measure brake pedal travel: a. Measure length (J) with the brake pedal at rest. b. Measure length (L) with the brake pedal depressed with a force of 182 ± 10 N (41 ± 2 lb). c. Subtract length (L) from length (J) to determine pedal travel (K). 2. Pedal travel (K) must be 80 ± 5 mm (3.1 ± .2 in) when pushed with a force of 182 ± 10 N (41 ± 2 lb).

How does the clutch work on a Caterpillar D4?