What is the service manual for a Volvo ec140b?
What is the service manual for a Volvo ec140b?
This is the complete factory service repair manual for the VOLVO EC140B LC EC140BLC EXCAVATOR. This Service Manual has easy-to-read text sections with top quality diagrams and instructions. They are specifically written for the do-it-yourself as well as the experienced mechanic.
What is the repair manual for a Volvo Excavator?
This VOLVO EC140B LC EC140BLC EXCAVATOR repair manual is an inexpensive way to keep you vehicle working properly. This professional technical manual contains service, maintenance, and troubleshooting information for your VOLVO EC140B LC EC140BLC EXCAVATOR, covering All Models/Engines/Trim/Transmissions Types.
What to do if your excavator is black?
If it is black then you are on the brake solenoid. Testing can be done with the key ON and the BACK-UP switch UP. The left switch is back-up and right switch is throttle. Check green wire for 24v and black wire for continuity to ground.
This is the complete factory service repair manual for the VOLVO EC140B LC EC140BLC EXCAVATOR. This Service Manual has easy-to-read text sections with top quality diagrams and instructions. They are specifically written for the do-it-yourself as well as the experienced mechanic.
When does a Volvo engine fault code become inactive?
Some fault codes become inactive when the engine is stopped. Start the engine to check whether the fault code is still inactive with the engine running. After an action with the connector. Put the connector back. Check if the fault code becomes inactive.
What causes fault code er32-00 on Volvo Excavator?
Condition: If the locomotive control unit (V-ECU) records a voltage on JA56 below o.95V (open circuit), the fault code ER32-00 will be generated. Possible cause: The proportional valve drive circuit is open; the proportional valve circuit (frame ground wire) is open; the V-ECU’s JA pin is damaged.
This VOLVO EC140B LC EC140BLC EXCAVATOR repair manual is an inexpensive way to keep you vehicle working properly. This professional technical manual contains service, maintenance, and troubleshooting information for your VOLVO EC140B LC EC140BLC EXCAVATOR, covering All Models/Engines/Trim/Transmissions Types.
Some fault codes become inactive when the engine is stopped. Start the engine to check whether the fault code is still inactive with the engine running. After an action with the connector. Put the connector back. Check if the fault code becomes inactive.
Condition: If the locomotive control unit (V-ECU) records a voltage on JA56 below o.95V (open circuit), the fault code ER32-00 will be generated. Possible cause: The proportional valve drive circuit is open; the proportional valve circuit (frame ground wire) is open; the V-ECU’s JA pin is damaged.
How are Sid numbers determined on a Volvo Excavator?
Each parameter has a Volvo unique number. SID: Subsystem Identification D eion (represents component identification). The SID numbers are determined by which control component (MID) they are transmitted from. Each control component has its own sequence of SID numbers. The exceptions are the SID numbers 151-255, which are common to all systems.
How much does an ec140b lcvolvo excavator weigh?
EC140B LCVOLVO EXCAVATOR • Engine power, gross: 73 kW 98 hp • Operating weight: 13.4 ~ 15.2 t 29,529 ~ 33,450 lb • Buckets (SAE): 600 ~ 975 l 0.78 ~ 1.28 yd3 • Turbocharged Volvo diesel engine with direct injection meets EPA Tier 2 emission standards • Contronics, Volvo’s advanced mode selection system and electronically-controlled system
How much hydraulic lifting capacity does ec140b LC have?
Rated loads do not exceed 87% of hydraulic lifting capacity or 75% of tipping load.
EC140B LCVOLVO EXCAVATOR • Engine power, gross: 73 kW 98 hp • Operating weight: 13.4 ~ 15.2 t 29,529 ~ 33,450 lb • Buckets (SAE): 600 ~ 975 l 0.78 ~ 1.28 yd3 • Turbocharged Volvo diesel engine with direct injection meets EPA Tier 2 emission standards • Contronics, Volvo’s advanced mode selection system and electronically-controlled system
Rated loads do not exceed 87% of hydraulic lifting capacity or 75% of tipping load.
